Abstract:This study focused on the numerical simulation of the distribution of residual stress in yttria-stabilized zirconia (YSZ) coatings prepared with atmospheric plasma spraying (APS). We particularly investigated the stress distribution around the interface between the top coat and bond coat. During thermal spray deposition, droplets and particles deposit on the substrate in a complex manner, causing interface waviness and non-uniform stress distribution. Therefore, residual stress is an important consideration when preparing thermal barrier coatings (TBCs). Residual stresses directly affect the performance of bond coats (BCs) and ceramic top coats (TCs). To accurately evaluate residual stress, we considered interface waviness and the thickness of the ceramic top coat and conducted a detailed analysis of stress distribution. The results show that compressive stress exists at the TC/BC interface, which may be caused by the mismatch in the thermal expansion coefficient between the YSZ top coat and the substrate, potentially leading to coating delamination. Moreover, the residual stress at the TC/BC interface significantly increases with an increasing YSZ thickness. When the top-coat thickness exceeds 300 μm, stress concentration and failure of the coating are likely to occur. Meanwhile, the optimized thermal spray experiment results confirm that the residual stress at the BC/YSZ interface of the thermal barrier coating is tensile stress, with a maximum value of 155 MPa, which is consistent with the finite element calculation results. Furthermore, the failure modes of TBCs with rough interface conditions are discussed in detail. Our research provides important guidance for TBC design and optimizing their performance.

Residual Stresses in Thermal Barrier Coatings Measured by Photoluminescence Piezospectroscopy and Indentation Technique

Residual Stress Inspection by Eu3+ Photoluminescence Piezo-Spectroscopy: an Application in Thermal Barrier Coatings

Residual Stress Measurement of Thermal Barrier Coatings

Characterization of Micro-Scale Residual Stress Around Thermal Grown Oxide Using Micro-Slotting Method and Geometric Phase Analysis

OS13F106 Progress of the Residual Stress Measuring Techniques of Thermal Barrier Coatings

Thermal‐cycle Dependent Residual Stress Within the Crack‐susceptible Zone in Thermal Barrier Coating System

Cross-Sectional Residual Stresses in Thermal Spray Coatings Measured by Moiré Interferometry and Nanoindentation Technique

High Temperature Fracture Toughness and Residual Stress in Thermal Barrier Coatings Evaluated by an In-Situ Indentation Method

THz-TDS characterization of stress evolution of EB-PVD TBCs under thermal cycling

Measurement of the Elastic Modulus and Residual Stress of Thermal Barrier Coatings Using a Digital Image Correlation Technique

Precise Strain Profile Measurement As a Function of Depth in Thermal Barrier Coatings Using High Energy Synchrotron X-rays

Failure of Electron Beam Physical Vapor Deposited Thermal Barrier Coatings System under Cyclic Thermo-Mechanical Loading with a Thermal Gradient

Growth selection induced residual stresses and fracture behavior of as‐deposited thermal barrier coatings

Effect of Thermal Growth Oxide Composition and Morphology on Local Stresses in Thermal Barrier Coatings

Numerical and Experimental Investigation of Residual Stress in Thermal Barrier Coatings During Aps Process

Effect of Top-Coat Thickness and Interface Fluctuation on the Residual Stress in APS-TBCs

Failure behaviour of EB-PVD YSZ thermal barrier coatings under simulated aero-engine operating conditions

Residual stress evolution of 8YSZ:Eu coating during thermal cycling studied by Eu3+ photoluminescence piezo-spectroscopy

Uncertainty of the X-ray Diffraction (XRD) sin2 ψ Technique in Measuring Residual Stresses of Physical Vapor Deposition (PVD) Hard Coatings

Simulation of Residual Stresses and Their Effects on Thermal Barrier Coating Systems Using Finite Element Method

Investigation of Pile-Up Behavior for Thermal Barrier Coatings under Elevated-Temperature Indentation