Abstract:The durability of infrastructure materials, such as concrete, has direct impact on society because the productivity of many industries and safety of human beings depend on infrastructure condition, and further because maintenance of the infrastructure can represent a significant portion of a government’s budget. Thus the enhancement of concrete durability and improvement of infrastructure condition monitoring are significant concerns to the scientific community. The resonant frequency method has been traditionally used to assess the mechanical condition of concrete. Resonance frequencies of a solid body depend on test sample mass and dimensions, elastic properties, and boundary conditions. Resonance frequencies have been used to determine engineering properties such as the elastic moduli and material damping. The method is useful to assess the performance of materials within accelerated degradation durability test procedures, and to inspect quality of the products during manufacturing processes (pass/fail tests). Different testing standards and recommendations prescribe test configurations, and specific tests are recommended for different materials. A basic resonant frequency test requires a forced vibration system to set up mechanical resonances, and some system to sense the frequency content from the resonant vibration signals. For concrete-like materials, these specifications are given by ASTM C215 [1], wherein an impulsive impact event is applied to the test sample to excite the resonant frequencies and a small sensor is mounted on the surface of the test sample. From the impulsive impact vibration signals thus obtained, two standard parameters are usually derived: (1) the dynamic modulus, which depends on sample dimensions, mass, and the resonant frequency peak (f), and (2) the attenuation or damping capacity of the material. Figure 12.1a, b illustrates typical signals obtained from a single-impact vibration test, where the spectral (frequency domain) signal is computed from the time signal using a Fourier transform algorithm. The continuous reduction of the vibration signal amplitude with time during the signal “ring-down” is seen in the time domain signal. The resonant frequency and damping characteristics are extracted from the spectral signal in the region around the resonant frequency peak. The damping capacity of the material is determined from the quality factor (Q) (or inverse attenuation), which is defined as the ratio between the resonant frequency peak (f) and the bandwidth frequencies corresponding to a 50% reduction of vibration energy in the power frequency spectrum for a given vibration mode [2]. Meaningful application of the ASTM C215 test is found within other standard durability test methods [3, 4].

Response Frequency Spectrum Analysis for Impact Behavior Assessment of Surface Materials

Frequency Spectrum Analysis of Impact Response for Plasma Sprayed Coatings

Impact Evaluation Of Plasma Spray Coatings

Angular Measurement of Acoustic Reflection Coefficients by the Inversion of V(z, T) Data with High Frequency Time-Resolved Acoustic Microscopy

Effect of ultrasonic impact treatment on the microstructure and properties of laser cladded CoCrFeNiMo x high entropy alloy coatings

Effects of Impact Energy, Impact Frequency, and Test Time on Impact Wear Characteristics of Zirconia-Toughened Alumina Particles-Iron (ZTAp-Fe) Composites Using Response Surface Methodology

Impact wear behavior of laser hardened hypoeutectoid 2Cr13 martensite stainless steel

Nanoindentation characterization of the surface mechanical properties of a 17-4PH stainless steel substrate treated with grit blasting and coated with a Cr3C2-NiCr coating

Finite Element Simulation of Laser Spallation Technique

Particle Impact Damage and Point Load-Induced Fracture Behavior in Zirconia Plasma Spray Coating Film

Analytical method for parameterizing the random profile components of nanosurfaces imaged by atomic force microscopy

Ion beam microprobe analysis for friction-induced material transfer processes in ta-C/steel and ta-C/brass pairs

New method for position and energy controlled surface mechanical attrition treatment and its effects in 304 stainless steel

Accumulative Damages of Thermally Sprayed Cemented Carbide Coatings Under Repetitive Heavy-Load Impacts

A dispersion-based impact identification method: mechanical model and experimental verification

An Evaluation of the Impact Effect on the Surface Microstructure and Its Induced Temperature Changes during Ultrasonic-Assisted Micro-Forging

The effect of heat treatment and impact angle on the erosion behavior of nickel-tungsten carbide cold spray coating using response surface methodology

Cement-Based Material Characterization Using Nonlinear Single-Impact Resonant Acoustic Spectroscopy (NSIRAS)

Dynamic response and roughness control of surface materials on TC4 titanium alloy subjected to laser shock wave planishing

Effect of ultrasonic impact treatment on surface stress evaluation of laser cladding coating by using critically refracted longitudinal wave

Enhanced Wear Behavior of a Stainless Steel Coating Deposited on a Medium-Carbon Low-Alloy Steel Using Ultrasonic Impact Treatment