Abstract:Porous Si2N2O/SiC ceramics is facilitated at 1200 °C for 10 min by microwave sintering. Rapid in‐situ production of Si2N2O fibers provided high mechanical properties of the samples. The porosity of the prepared sample is tailorable and the thermal insulation effect is excellent. Two steps strategy were taken to effectively produce porous Si2N2O/SiC ceramics: 1) direct foaming combined with sol‐gel curing at room temperature to form a green body, and 2) sintering assisted by in‐situ production of Si2N2O fibers under microwave sintering conditions. Non‐toxic silica sol was used to provide silicon source for in‐situ synthesis of Si2N2O, the silica sol could form a gel that stabilizes the bubbles, creating a porous structure. A thorough investigation was conducted into how different sintering temperatures affected the microstructure, flexural strength, and porosity of the porous Si2N2O/SiC composites. The main bonding phase in the porous composites was the Si2N2O with fiber morphology. The optimal microwave sintering temperature for fabricating porous Si2N2O/SiC ceramics, using a combination of sol‐gel and direct foaming techniques, has been determined to be 1200 °C. At this temperature, the porosity can be controlled between 73.32% and 83.16% by proportionally adjusting the ratio of the raw materials. Under the condition of high porosity, the thermal radiation is dominant and the thermal conductivity increases with the increase of temperature. With the decrease of porosity, the heat conduction is dominant, and the thermal conductivity decreases with the increase of temperature.

POROUS Β-Sialon/si3n4 CERAMICS PREPARED BY REACTIVE SINTERING

Optimization of Microstructure to Improve Si3n4 Ceramics with Thermal Conductivity and Mechanical Properties: Effect of Si and Α-Si3n4 Powder Composition

Cost-effective Fabrication of Porous Α-Sialon Bonded Β-Sialon Ceramics

Preparation And Properties Of High Strength Porous Si3n4 Ceramics

Synthesis and Mechanical Properties of Highly Porous Ultrafine-Grain Si3N4 Ceramics Via Carbothermal Reduction-Nitridation Combined with Liquid Phase Sintering

Preparation of Porous Si2N2O/SiC Ceramics by Microwave Sintering

Microstructure and properties of porous Si3N4 ceramics by gelcasting-self-propagating high-temperature synthesis (SHS)

Novel porous Si3N4 ceramics prepared by aqueous gelcasting using Si3N4 poly-hollow microspheres as pore-forming agent

Study on Micro-structure and Properties of Al2O3/SiC Ceramics by Pressureless Sintering in Air

Microstructure and Properties of Porous Si3n4 Ceramics with A Dense Surface

Preparation of porous Si 3 N 4 ceramics via tailoring solid loading of Si 3 N 4 slurry and Si 3 N 4 poly-hollow microsphere content

INFLUENCE OF Al2O3 ON PREPARING POROUS SILICON NITRIDE BASED CERAMIC FROM RICE HUSK

Preparation and Properties of Porous Si<sub>3</sub>N<sub>4</sub>/SiO<sub>2</sub>/BN Composite Ceramics

Simultaneous improvement in porosity and strength of porous β-Si3N4 ceramics by formation of ultrafine fibrous grains

A New Al 2 O 3 Porous Ceramic Prepared by Addition of Hollow Spheres

Si3N4 Hollow Microsphere Toughened Porous Ceramics from Direct Coagulation Method Via Dispersant Reaction

Preparation and Properties of Porous Silicon Carbide Ceramics Through Coat-Mix and Composite Additives Process

Fabrication of Si 3 N 4 ceramics with high thermal conductivity and flexural strength via novel two-step gas-pressure sintering

Microstructure Evolution Process of Porous Silicon Carbide Ceramics Prepared Through Coat-Mix Method

Preparation and properties of porous Si 3N 4/SiO 2/BN composite ceramics

Morphology Design of Porous Si2N2O Ceramics via Silica Poly-Hollow Microspheres