Abstract:Lath martensite with a dislocation substructure is one of the most common forms of martensite in structural steels. Surface relief has been regarded as an important characteristic in the martensitic transformation. Crystallographic features on surface relief are essential to get into deep insight of the long range strain field in the transformation, and explore the mechanism of the phase transformation. However, very limited experimental data on the shape strain associated with the formation of surface relief caused by the lath martensite have been reported so far, especially for the quantitative study of the displacement; vector. The present investigation was carried out to study the shape deformation in the formation of the lath martensite on the austenite matrix in an Fe-20.2Ni5.5Mn (mass fraction, %) alloy. The shape strain accompanying surface relief, such as the magnitude and direction of the displacement vector, has been concerned in a quantitative way. The morphology of the relief was studied by the optical microscope (OM) and the atomic force microcope (AFM). The orientations of the matrix grain and the lath were measured by the electron backscattered diffraction (EBSD), respectively, which was used to determine the orientation of the habit plane, and the orientation relationship (OR) between the lath martensite and its neighboring matrix. Combing the data from EBSD and AFM, it is concluded that the relief is produced by a single bee crystal, which exhibits a tent-shaped relief. Based on an electron backscattered diffraction analysis, the austenite/martensite orientation relationship is found to be in the closer vicinity of K-S orientation relationship, which is consistent with that in bulk materials obtained by transmission electron microscope (TEM), and the habit plane is determined to be near (1 (1) over bar(1) over bar)(f). The largest shear angle for the relief is calculated to be 27.49 degrees, and the directions of combined displacement vector are scattered around [12 (1) over bar](f). However, the observed maximum surface tilt angle is 22.41 degrees, which is smaller than the calculated value. Considering the habit plane is not perpendicular to the pre-polishing surface, the measured smaller value of tilt angles is reasonable.

Study on the Orientational Relationship Between Martensite Variants by EBSD

Effect of Crystallographic Orientation on Quenching Stress During Martensitic Phase Transformation of Carbon Steel Plate

Crystallographic Analysis of Lath Martensite in a 13Cr-5Ni Steel by Electron Backscattering Diffraction

Tetragonality mapping of martensite in a high-carbon steel by EBSD

Determination of the orientation relationship between austenite and incommensurate 7M modulated martensite in Ni–Mn–Ga alloys

A crystallographic model of the {557} habit planes in low-carbon martensitic steels

Mapping of lattice distortion in martensitic steel-Comparison of different evaluation methods of EBSD patterns

Link between b.c.c.–f.c.c. orientation relationship and austenite morphology in CF8M stainless steel

Revisiting the Crystallography of {225}γ Martensite: How EBSD Can Help to Solve Long-Standing Controversy

Crystallographic orientation assessment by electron backscattered diffraction

Pitsch and t-h orientation relationships between widmanstatten cementite and austenite

A TEM Study of the Crystallography of Austenite Precipitates in a Duplex Stainless Steel

Fracture Mode Identification of Low Alloy Steels and Cast Irons by Electron Back-Scattered Diffraction Misorientation Analysis

Quantitative Analysis for the Displacement of Tent-Shaped Surface Relief of Lath Martensite in Fe-Based Alloy

Butterfly martensite in industrial steels

Identification and quantification of martensite in ferritic-austenitic stainless steels and welds

Determination of strain path during martensitic transformation in materials with two possible transformation orientation relationships from variant self-organization

The orientation relationships of the low temperature martensite transformation in metastable β-brass

Variant selection mechanism by elastic anisotropy and double K-S relation for transformation texture in steel; difference between martensite and ferrite

Relationship between crystallographic structure of the Ti2O3/MnS complex inclusion and microstructure in the heat-affected zone (HAZ) in steel processed by oxide metallurgy route and impact toughness

High resolution electron backscatter diffraction study on the heterogeneities of tetragonal distortion in Fe-C martensite at the microstructural scale