Abstract:The anisotropic fracture behavior of cold-drawn pearlitic steels was analyzed up to a true strain of 1.6. The structures were analyzed and quantified by scanning electron microscopy, electron backscatter diffraction and high-resolution electron microscopy. The aspect ratio Λ was defined to describe the fracture mechanism based on statistics pertaining to major axis and minor axis of pearlitic colonies, and the fitting formula was established as follows: Λ=0.4exp(2x)+0.65. At Λ ≤ 2.75, the fracture mechanism shifts from cleavage to quasi-cleavage fracture due to dislocation generation, as the measured parameters of interlamellar spacing (ILS) showed no obvious decrease. At values of Λ > 2.75, ductile fracture mechanism becomes dominant due to a drastic decrease in ILS. The <110> ferrite fiber microtexture formed during the cold drawing process and the component exhibiting a gradient distribution from the surface to the central regions increased gradually with drawing. The crack propagation path was then deflected and formed a ‘V’ shape at ε ≤ 1.5. However, as carbon migrated from cementite to the ferrite near the interphase, the fracture path deflected again. Furthermore, two reasonable models were formulated to explain fracture crack forming and anisotropic fracture behavior. In addition, this study illustrated that the relative crystallographic orientation of the ferrite and cementite components followed the Bagarytski relationship. With increasing strain, the cementite layers transformed from single crystals into nanostructured polycrystals and even evolved an amorphous structure at the interface at strains above 1.5.

Fracture Mode Identification of Low Alloy Steels and Cast Irons by Electron Back-Scattered Diffraction Misorientation Analysis

EBSD Analysis of Cyclic Load Effect on Final Misorientation Distribution of Post-Mortem Low Alloy Steel: A New Method for Fatigue Crack Tip Driving Force Prediction

Semi-quantitative creep-fatigue damage analysis based on diffraction-based misorientation mapping and the correlation to macroscopic damage evolutions

Crystal Orientation Effect on Fretting Fatigue Induced Geometrically Necessary Dislocation Distribution in Ni-based Single-Crystal Superalloys

Cracking in a Fe–25Mn–3Si–3Al Steel

Quantitative analysis of the deformation modes and cracking modes during low-cycle fatigue of a rolled AZ31B magnesium alloy: The influence of texture

EBSD analysis of creep deformation induced grain lattice distortion: A new method for creep damage evaluation of austenitic stainless steels

Measurement of Crystal Orientation around the Fatigue Crack in Iron Films Using EBSD Method

Microstructural Dependence of Anisotropic Fracture Mechanisms in Cold-Drawn Pearlitic Steels

The Correlation of Fractal Dimension to Fracture Surface Slope for Fatigue Crack Initiation Analysis under Bending-Torsion Loading in High-Strength Steels

In-situ observation of strain evolution and ratchetting of growing fatigue cracks

Crystallographic orientation and spatially resolved damage for polycrystalline deformation of a high manganese steel

Fracture parameters analysis of compact tension specimens with deflected fatigue cracks: ZK60 magnesium alloy

Mixed-mode Fracture Behaviors of AISI 1045 and AISI 5140 Steels in Compressor Crankshafts – Part I: Mode I-III

Effect of orientations on in situ tensile deformation and fracture behaviours of nickel-base single-crystal superalloys

Crystal plasticity modeling of grain boundary softening and fatigue in U75V pearlite steel under low strain conditions: A study of cyclic rolling contact fatigue

Lattice Rotation Dependence on Microstructural Characteristics in a Low Carbon Steel

In-situ Observations of the Effects of Orientation and Carbide on Low Cycle Fatigue Crack Propagation in a Single Crystal Superalloy

In-situ SEM and EBSD Study on Fretting Fatigue Crack Initiation of a Directionally Solidified Ni-based Superalloy

Effects of Temperature and Load on Fretting Fatigue Induced Geometrically Necessary Dislocation Distribution in Titanium Alloy

In-situ SEM-EBSD investigation of the low-cycle fatigue deformation behavior of Inconel 718 at grain-scale