Abstract:A new constitutive model is proposed for the description of induced anisotropic damage in brittle rocks. The formulation of the model is based on relevant results from the micromechanics consideration. The distribution of microcracks is approximated by a second order damage tensor. The effective elastic properties of damaged material are derived from the free enthalpy function. The evolution of damage is directly related to the growth of microcracks in different space orientations. The volumetric dilatancy due to sliding crack opening is taken into account. The model is extended to the description of creep deformation in brittle rocks. The time dependent deformation is seen as a consequence of the sub-critical propagation of microcracks due to stress corrosion process. The proposed model is applied to a typical brittle rock, the Lac du Bonnet granite. A general good agreement is obtained between numerical simulations and experimental data. Anisotropic damage due to microcracks is an essential mechanism of inelastic deformation and failure in most brittle rocks. Many experimental tests have confirmed various mechanisms of nucleation and growth of microcracks. Under compressive stresses, sliding wing cracks seem to be the principal propagation mode of microcracks (Brace and Bombolakis 1963; Nemat-Nasser and Horii 1982; Wong 1982; Stef 1984; Olsson 1995). Due to roughness of crack surfaces in geomaterials, the crack sliding may induce an associated aperture which is an origin of volumetric dilatancy in these materials (Nemat-Nasser and Obata 1988). When the crack length reaches some critical values, the coalescence of microcracks occurs and localized macro-cracks appear leading to the failure of material. The kinetics of failure is controlled by confining pressure and there is a transition from brittle failure to ductile failure when the confining pressure increases (Fredrich et al. 1989; Horii and Nemat-Nasser 1985, 1986). The main consequences of induced microcracks are: non linear stress-strain relations, deterioration of elastic properties, induced anisotropy, volumetric dilatancy, irreversible strains due to residual crack opening, unilateral response due to crack closure, and hysteresis associated with frictional mechanism. These features have to be considered in the constitutive modelling. Two families of damage models have been developed for the description of induced damage: micromechanical approaches and phenomenological models (we do not give here an exhaustive list of many models reported in the literature). The main advantage of micromechanic al approaches is the ability to account for physical mechanisms involved in the nucleation and growth of microcracks. For the construction of a micromechanical model, two steps are generally performed. The first step consists in the evaluation of the effective elastic properties of material weakened by microcracks. The second step is to propose a suitable damage evolution law for microcrack growth. The main features related to microcrack growth, opening and closure, friction, interaction between cracks, could be taken into account in such micromechanical models. The macroscopic behaviour of material is then obtained through a homogenization procedure. This renders these models difficult to be applied to practical applications. Phenomenological models use internal variables to represent the density and orientation of microcracks, for instance, scalar variable for isotropic damage, second and fourth

Identification and measurement of ductile damage parameters

Continuum Models of Ductile Fracture: A Review

Experimental techniques for ductile damage characterisation

Ductile damage evolution under triaxial state of stress: theory and experiments

Towards Fully Automatic Modelling of the Fracture Process in Quasi-Brittle and Ductile Materials: a Unified Crack Growth Criterion

Anisotropic Damage Model under Continuum Slip Crystal Plasticity Theory for Single Crystals

A Stress-Invariant Based Multi-Parameters Ductile Progressive Fracture Model

Ductile Fracture: Experiments and Computations

A large strain gradient-enhanced ductile damage model: finite element formulation, experiment and parameter identification

A CDM Approach of Ductile Damage with Plastic Compressibility

Modeling ductile damage under fully reversed cycling

Continuum damage mechanics modelling incorporating stress triaxiality effect on ductile damage initiation

Development and Application of Ductile Damage

Numerical modeling of the evolution of ductile damage under proportional and non-proportional loading

Theoretical, numerical and identification aspects of a new model class for ductile damage

Mastering the art: Proficient finite element implementation and robust evaluation of a strain-hardening porous ductile material crack growth prediction model at finite strain

A new numerical approach for determination of the Lemaitre’s ductile damage parameter in bulk metal forming processes

A Continuous Damage Mechanics Model for Ductile Fracture

5569 - DAMAGE AND CREEP DEFORMATION IN BRITTLE ROCKS

Unified CDM Model and Local Criterion for Ductile Fracture—i. Unified CDM Model for Ductile Fracture

Practical Applicability and Limitations of the Elastic Modulus Degradation Technique for Damage Measurements in Ductile Metals