Abstract:Vat photopolymerization (VPP) 3D printing technology has broken through mold limitations and shown great potential to manufacture complex-structured ceramic cores for turbine blades. However, improving dimensional accuracy is difficult for the VPP 3D printed parts due to the high contraction deformation. Reducing shrinkage is a key challenge for developing 3D-printed ceramic cores. In this study, 3D-printed alumina ceramic cores with near-zero shrinkage in the X direction were achieved for the first time using a novel approach that was called atmosphere-controlled in-situ oxidation of aluminum powder. The in-situ oxidation reaction of the aluminum powder was creatively tuned by changing the atmosphere transition temperature from argon to air. Then, the microstructure and properties of the ceramic core could be controlled by the liquid-phase sintering with the participation of atmosphere-protected molten aluminum. As a result, the pore size of the ceramic cores was significantly increased by almost ten times, but the bonding strength of the grains was also increased. In addition, the powder consolidation generated by the action of molten aluminum was considered to be an important reason for reducing the linear shrinkage of ceramic cores. Under the optimized parameters, the linear shrinkage of the ceramic cores was as low as 0.3% in the X direction. The high apparent porosity (45.02%) and flexural strength (72.7 MPa) of the alumina ceramic cores were realized at the same time. The in-situ control of sintering by changing the atmosphere will be a creative method for regulating the properties of ceramic materials.

Near-zero-shrinkage Al2O3 ceramic foams with coral-like and hollow-sphere structures via selective laser sintering and reaction bonding

A Novel Process to High‐strength and Controlled‐shrinkage Al2O3 Foams with Open‐cell by Al Powder Hollowing Technology

Factors affecting the microstructure of a fine ceramic foam

Ultralight and High-Strength Bulk Alumina/zirconia Composite Ceramic Foams Through Direct Foaming Method

Non-shrinkage porous ceramics by In-situ hollow sphere method based on the Kirkendall effect of Al particle

Ultra-high Porosity of Open-Cell Alumina Ceramic Foams Prepared by Adding Tiny Amounts of Γ-Alo(oh) Sol

Ceramic foams with highly open channel structure from direct foaming method in combination with hollow spheres as pore-former.

Hierarchical porous MgAl2O4 ceramic in‐situ structured by hollow particles: Low‐shrinkage and High‐strength

High-strength, 3D interconnected alumina ceramic foams with high porosity comparable to aerogels

Foam structure-derived strong and tough alumina ceramics with fine grains and transgranular fracture

Ultra-high Strength ZTA Ceramic Foams with Large Amounts of Intragranular Structures Resulting from Dual-Phase Sol

New approach to preparing near zero shrinkage alumina ceramic cores with excellent properties by vat photopolymerization

Highly Porous Alumina Cellular Ceramics Bonded by In-Situ Formed Mullite Prepared by Gelation-Assisted Al2O3–Si Particle-Stabilized Foams

Ultrahigh-Strength Porous Ceramic Composites via a Simple Directional Solidification Process

Direct ink writing of aluminum-phosphate-bonded Al2O3 ceramic with ultra-low dimensional shrinkage

Preparation of low-shrinkage and high-performance alumina ceramics via incorporation of pre-sintered alumina powder based on Isobam gelcasting

Ultrahigh‐strength Alumina Ceramic Foams Via Gelation of Foamed Boehmite Sol

Near Net Size Sintering of Porous Cordierite Ceramics with Excellent Properties

Fabrication of alumina ceramics with high flexural strength using stereolithography

Low sintering shrinkage and high strength of porous mullite–zirconia ceramics: Effect of AlF3 and ZrSi2 contents

Porous Silica Ceramics with Uniform Pores from the In-Situ Foaming Process of Silica Poly-Hollow Microspheres in Inert Atmosphere