Abstract:Porous Si2N2O/SiC ceramics is facilitated at 1200 °C for 10 min by microwave sintering. Rapid in‐situ production of Si2N2O fibers provided high mechanical properties of the samples. The porosity of the prepared sample is tailorable and the thermal insulation effect is excellent. Two steps strategy were taken to effectively produce porous Si2N2O/SiC ceramics: 1) direct foaming combined with sol‐gel curing at room temperature to form a green body, and 2) sintering assisted by in‐situ production of Si2N2O fibers under microwave sintering conditions. Non‐toxic silica sol was used to provide silicon source for in‐situ synthesis of Si2N2O, the silica sol could form a gel that stabilizes the bubbles, creating a porous structure. A thorough investigation was conducted into how different sintering temperatures affected the microstructure, flexural strength, and porosity of the porous Si2N2O/SiC composites. The main bonding phase in the porous composites was the Si2N2O with fiber morphology. The optimal microwave sintering temperature for fabricating porous Si2N2O/SiC ceramics, using a combination of sol‐gel and direct foaming techniques, has been determined to be 1200 °C. At this temperature, the porosity can be controlled between 73.32% and 83.16% by proportionally adjusting the ratio of the raw materials. Under the condition of high porosity, the thermal radiation is dominant and the thermal conductivity increases with the increase of temperature. With the decrease of porosity, the heat conduction is dominant, and the thermal conductivity decreases with the increase of temperature.

Porous Silica Ceramics with Uniform Pores from the In-Situ Foaming Process of Silica Poly-Hollow Microspheres in Inert Atmosphere

Fabrication of Homogeneous Mullite-Based Fiber Porous Ceramics with High Strength and Porosity

Porous Si3N4-based Ceramics with Uniform Pore Structure Originated from Single-Shell Hollow Microspheres

Fabrication and Properties of Porous Mullite Ceramics from Directly Sintering Ceramic Microspheres

Effects of the Starting Powders on Microstructure and Properties of Porous Silica Ceramics

A Simple and Efficient Way to Prepare Porous Mullite Matrix Ceramics Via Directly Sintering SiO2-Al2O3 Microspheres

Morphology Design of Porous Si2N2O Ceramics via Silica Poly-Hollow Microspheres

Microstructure and properties of porous Si3N4 ceramics by gelcasting-self-propagating high-temperature synthesis (SHS)

A Novel Way to Prepare Hollow Sphere Ceramics

3D printing of porous SiC ceramics added with SiO2 hollow microspheres

Si3N4 Hollow Microsphere Toughened Porous Ceramics from Direct Coagulation Method Via Dispersant Reaction

Silica Foams With Ultra-Large Specific Surface Area Structured By Hollow Mesoporous Silica Spheres

In-situ Reaction Synthesis of Porous Si2N2O-Si3N4 Multiphase Ceramics with Low Dielectric Constant Via Silica Poly-Hollow Microspheres

A non-sintering fabrication method for porous Si3N4 ceramics via sol hydrothermal process

Selective laser sintering of porous Al2O3-based ceramics using both Al2O3 and SiO2 poly-hollow microspheres as raw materials

Fabrication, Structure and Properties of Porous SiC Ceramics with High Porosity and High Strength

In-situ synthesis and properties of porous cordierite ceramics with adjustable pore structure

Preparation of Porous Si2N2O/SiC Ceramics by Microwave Sintering

The Effect of SiO2 Addition on Phase and Microstructure of Porous Silica Ceramic

Novel porous Si3N4 ceramics prepared by aqueous gelcasting using Si3N4 poly-hollow microspheres as pore-forming agent

Ceramic foams with highly open channel structure from direct foaming method in combination with hollow spheres as pore-former.