Abstract:This article presents experimental analysis of heat removal capabilities of a wavy finned tube heat exchanger operating under natural convection conditions Two types of heat exchangers are considered in this work: standard construction exchangers, most often found in waste heat rejection devices and exchangers based on a novel geometry, which supports intensification of heat transfer processes under natural convection. The aim of the research was to experimentally verify the novel conception and to determine the thermal efficiency of heat exchangers under the influence of selected design parameters. The factors analyzed in the research include: temperature difference between the heat transfer surface and the surrounding air, different angles of the units transferring heat and the height of the exchanger casing. Four variants of the casing height were considered in this work. The conducted research also allowed to determine the influence of the fin spacing on the performance of the heat exchangers under natural convection conditions. The test results obtained show that the novel geometry allows for significance improvement of heat transfer efficiency. The proposed solution allowed to increase the density of the heat flux from 12% in (fin spacing of 2.8 mm) up to 24% (fin spacing of 5.6 mm). It was also observed that the height of the casing has significant impact on the heat transfer efficiency. For each of the analyzed cases, the heat exchanger without a casing was characterized by the lowest thermal efficiency, while the highest heat flux was removed from the exchanger with the highest casing (up to four times higher heat transfer rate). It was determined that the largest amount of heat was removed from exchangers located horizontally, while the exchanger with an angle of 60°, was characterized by the lowest rate of heat removal. Another factor which was determined to have significant impact on the performance of the heat exchangers is the spacing between the fins. The research results obtained shows that increasing the spacing of the finned surface from 2.8 mm to 5.6 mm resulted in an average twofold increase in thermal efficiency in the case of four-row exchangers and an almost threefold increase in the case of two-row exchangers. The obtained results can be used as basic guide for the development of finned tube heat exchangers operating under natural convection conditions.

Innovative analysis of local and average air-side heat transfer coefficients in fin-and-tube heat exchangers using CFD and experimental method

Parametric Study and Multiple Correlations on Air-Side Heat Transfer and Friction Characteristics of Fin-and-tube Heat Exchangers with Large Number of Large-Diameter Tube Rows

Numerical study of local heat transfer coefficient and fin efficiency of wavy fin-and-tube heat exchangers☆

Comparison of Individual Air-Side Row-By-Row Heat Transfer Coefficient Correlations on Four-Row Finned-Tube Heat Exchangers

Numerical Simulation of Heat Transfer in Finned Tube of Heat Recovery Unit Using Fluid-Solid Coupled Method

Numerical studies on heat transfer and pressure drop characteristics of flat finned tube bundles with various fin materials

Experimental and numerical investigation on air-side performance of fin-and-tube heat exchangers with various fin patterns

Numerical Simulation of Natural Convection Heat Transfer for Annular Elliptical Finned Tube Heat Exchanger with Experimental Data

Airside Fin Efficiencies for Finned-Tube Heat Exchangers with Forced Convection

Numerical Simulation of the Flow and Heat-Transfer Characteristics of an Aligned External Three-Dimensional Rectangular-Finned Tube Bank

Numerical Estimation of Heat Transfer Characteristics for Two-Row Plate-Finned Tube Heat Exchangers with Experimental Data

Experimental and Numerical Investigation of the Air Side Heat Transfer of a Finned Tubes Heat Exchanger

Numerical Simulation of Heat Transfer Characteristics of Finned Tube Heat Exchanger at Different Flow Velocities

Numerical study of air-side performance of a finned flat tube heat exchanger with crossed discrete double inclined ribs

Mathematical Investigation of Heat Transfer Characteristics and Parameter Optimization of Integral Rolled Spiral Finned Tube Bundle Heat Exchangers

Experimental Study on Heat Transfer and Pressure Drop Characteristics in a Microchannel Heat Exchanger Assembly with S-shaped Fins

Numerical Study of Fin-and-Tube Heat Exchanger in Low-Pressure Environment: Air-Side Heat Transfer and Frictional Performance, Entropy Generation Analysis, and Model Development

Experimental Determination of the Heat Transfer Coefficient of a Plate-Fin Heat Exchanger

Variable-dimension optimization study and design of internally finned helically coiled tubes heat exchangers based on numerical simulation and experiment

Experimental comparison of finned tube heat exchangers for heat rejection under natural convection conditions

A Comparative Study Of Fin-And-Tube Heat Exchangers With Various Fin Patterns