Abstract:Laser powder bed fusion (LPBF) is a powder-bed-based metal additive manufacturing process with multiple influencing parameters as well as multi-physics interaction. The laser scanning speed, which is one of the essential process parameters of the LPBF process, determines the microstructure and properties of the components by adjusting the instantaneous energy input of the molten pool. This work presents a comprehensive investigation of the effects of the laser scanning speed on the densification behavior, phase evolution, microstructure development, microhardness, and tensile properties of K418 alloy prepared by laser powder bed fusion. When the scanning speed is 800 mm/s, the microstructure of the material is dominated by cellular dendrite crystals, with coarse grains and some cracks in the melting tracks. When the scanning speed is increased to 1200 mm/s, a portion of the material undergoes a cellular dendrite–columnar crystal transition, the preferred orientation of the grains is primarily (001), and internal defects are significantly reduced. When the scanning speed is further increased to 1600 mm/s, columnar crystals become the main constituent grains, and the content of high-angle grain boundaries (HAGBs) within the microstructure increases, refining the grain size. However, the scanning speed is too fast, resulting in defects such as unmelted powder, and lowering the relative density. The experimental results show that by optimizing the laser scanning speed, the microhardness of the LPBF-ed K418 parts can be improved to 362.89 ± 5.01 HV, the tensile strength can be elevated to 1244.35 ± 99.12 MPa, and the elongation can be enhanced to 12.53 ± 1.79%. These findings could help determine the best scanning speed for producing K418 components with satisfactory microstructure and tensile properties via LPBF. In addition, since the LPBF process is largely not constrained and limited by the complexity of the geometric shape of the part, it is expected to manufacture sophisticated and complex structures with hollow, porous, mesh, thin-walled, special-shaped inner flow channels and other structures through the topology optimization design. However, due to the relatively narrow LPBF process window, this study will benefit from LPBF in producing a lightweight, complex, and low-cost K418 product, greatly improving its performance, and promoting the use of LPBF technology in the preparation of nickel-based superalloys.

Influence of the scanning angle on the grain growth and mechanical properties of Ni10Cr6W1Fe9Ti1 HEA fabricated using the LPBF–AM method

Effect of Scanning Angle on Grain Growth and Mechanical Properties of Ni10cr6w1fe9ti1 Hea

Unravelling heterogeneities in sub-grain cellular structure and micromechanical response of additive manufactured Ti-Nb alloys

Grain boundary network evolution in electron-beam powder bed fusion nickel-based superalloy Inconel 738

Temperature gradient induced tough-brittle transition behavior of a high-strength Al-4.2Mg-0.4Sc-0.2Zr alloy fabricated by laser powder bed fusion additive manufacturing

Laser metal deposition of thin-walled parts of Al 0.8 CrFe 2 Ni 2 high-entropy alloy: Process window, microstructure, wear resistance and mechanical anisotropy

Effect of Grain Orientation on Microstructure and Mechanical Properties of FeCoCrNi High-Entropy Alloy Produced via Laser Melting Deposition

Enhanced magnetic-field-induced strain of Ni-Mn-In alloy by altering laser scanning strategy during laser powder bed fusion

The evolution of microstructure and mechanical properties of Inconel 625 alloy fabricated by laser powder bed fusion via novel hybrid scanning strategy

Influence of the scanning strategy on the microstructure and the tribological behavior of a Ni-based superalloy processed by additive manufacturing

Grain morphology and mechanical properties tailoring of Inconel 625 alloy fabricated by laser powder bed fusion

Grain-anisotropied High-Strength Ni6Cr4WFe9Ti High Entropy Alloys with Outstanding Tensile Ductility

Alloying Effects on the Microstructure and Properties of Laser Additively Manufactured Tungsten Materials

In-situ investigation of deformation behavior in additively manufactured FeCoCrNiMn high entropy alloy

Nano-Mechanical Properties and Creep Behavior of Ti6Al4V Fabricated by Powder Bed Fusion Electron Beam Additive Manufacturing

Effect of Laser Scanning Speed on the Microstructure and Mechanical Properties of Laser-Powder-Bed-Fused K418 Nickel-Based Alloy

Effect of grain refinement on strain hardening behavior of nickel-based superalloy fabricated by wire arc additive manufacturing

Grain refinement and mechanical properties improvement of Inconel 625 alloy fabricated by ultrasonic-assisted wire and arc additive manufacturing

Effect of laser scanning angle on shear slip behavior along melt track of selective laser melted 316L stainless steel during tensile failure

Tuning of the Mechanical Properties of a Laser Powder Bed Fused Eutectic High Entropy Alloy Ni30Co30Cr10Fe10Al18W2 Through Heat Treatment

Effects of the microstructure and texture characteristics on mechanical properties of the Al–Ni–Cu–Fe alloy manufactured by laser powder bed fusion