Abstract:In this study, structural, morphological, thermal and magnetic properties of amorphous-nanocrystalline Fe 70 Cr 10 Nb 10 B 10 (at.%) alloy are discussed. The formation and evaluation of amorphous-nanocrystalline structures of the alloy were followed by XRD, SEM-EDX, TEM, DTA, and VSM techniques. After 50 h of milling Cr, Nb, and B were completely dissolved into the Fe lattice forming 82% of the amorphous phase of the alloy. A gradual dissolution of the alloying elements also increased the lattice parameters concurrently. The lattice parameters reached a maximum value of 2.908 Å after 20 h of milling and then leveled off to a value of 2.891 Å at the end of 50 h of milling. Based on the XRD data, crystallite size and lattice strain of the alloy were calculated as 3.2 nm and 3.34% respectively. TEM analyses revealed that the alloy particulates comprised needle-shaped nanoparticles of an average size of 21 nm. The room temperature magnetic hysteresis loops showed that the increased duration of milling decreased the saturation magnetization from 91 to 24 emu/g. This was mainly due to the upsurge on the amorphous phase content in the alloy as the milling progressed. The increase in amorphous phase content and the subsequent reduction of the saturation magnetization were due to the inter-diffusion of the non-ferromagnetic Cr and B atoms into the Fe lattice. Thermal studies revealed that around 350 °C the amorphous phase of the alloy began crystallizing. The magnetic saturation of the heat-treated alloy also increased with the growth in the crystalline phases. The 50 h milled sample annealed at 700 °C was found to have the highest magnetic anisotropy as observed from the temperature-dependent zero-field cooled and field cooled magnetization measurements. The high-pressure X-ray diffraction measurements revealed that the amorphous state of the alloy remained stable up to 11.3 MPa. It also revealed the structural similarities of the Fe 70 Cr 10 Nb 10 B 10 alloy with those of the Fe 70 M 10 B 20 (M = Nb and Cr) types. For all practical purposes, the microstructural stability under high compressive pressure represents the consolidation properties of the nanostructured magnetic materials since both pressure and temperature-induced phase transformations are the primary controlling factors for the specific magnetization properties of the alloy.

Morphology and microstructure of Fe–Cr–W–B alloy powders prepared by argon gas atomization

Study on Flowability Regulation of Vacuum Gas-Atomized Fe-Cr-Ni-W-B Spherical Powder

Microstructural Evolution of Gas Atomized Fe-25cr-3. 2c Alloy Powders

Solidification Process, Microstructure, and Mechanical Properties of Cr-doped High Boron Fe-based Alloy

Fe-based Amorphous Soft Magnetic Powders Fabricated by Water Atomization

Investigations on Microstructure, Mechanical Properties and Abrasion Resistance of 4Wt%cr-2Wt%mn-2wt%cu-fe-b Alloy

Fabrication of nanocrystalline supersaturated W–Al alloys with enhanced thermal stability and high sinterability

Preparation of ultrafine (W,Mo)B, (W,Mo)B2.5 and (Mo,W)AlB solid solution composite powders

Microstructure and Crystallography of Borides and Mechanical Properties of Fe–B–C–Cr–Al Alloys

The crystallization process of a−Fe 35 Ni 15 B 26 ultrafine particles produced by reduction with borohydride

Microstructure Evolution and Mechanical Properties of Fe–Cr–B Alloys with Varying Mo Additions

Microstructure and Its High Temperature Oxidation Behavior of W-Cr Alloys Prepared by Spark Plasma Sintering

Reactive synthesis and phase evolution of W 2 FeB 2 alloy powders

Microstructure and some properties of powder-pack borided Ti–5Mo–5V–8Cr–3Al alloy with special attention to the microstructure at the interface TiB/substrate

Chemical Preparation and Investigation of Fe-P-B Ultrafine Amorphous Alloy Particles

Synthesis and characterization of amorphous-nanocrystalline Fe70Cr10Nb10B10 powders by mechanical alloying

Synthesis of Ultrafine Fe-W-Al-Ti-Ni-C-B Powders by Mechanical Alloying

Sintering Properties and Microstructure of Fe-Ni-Co-based Superalloy Atomized Powder

Formation of Crystalline and Amorphous Solid Solutions of W–Ni–Fe Powder During Mechanical Alloying

The Effect of the Nucleation Ability on Solidified Microstructures of Gas-Atomized Fe–6.5 Wt.%si Alloy Powder

Microstructure Evolution and Mechanical Properties of Ultra-Fine Grain AlCrFe2Ni2Wx High-Entropy Alloys