Abstract:As a kind of cast aluminum alloy with high strength, Al-Li-Cu-Mg series alloys exhibit desirable stiffness and formability, while a limited investigation has discussed the influence of cooling rate on microstructure and mechanical properties of these alloys. In this work, the effect of cooling rate during casting on microstructure evolution and mechanical properties of cast Al-2Li-2Cu-0.5Mg-0.15Sc-0.1Zr-0.1Ti alloy was investigated using a step-like iron mold. The results showed that the increased cooling rate refined the grain size and augmented the volume fraction of second phase in the as-cast microstructure. In the aging process, the rapid cooling rate markedly promotes precipitation and suppresses coarsening of the & delta;"(Al3Li), T1(Al2CuLi) and S"(Al2CuMg) phases, which plays a vital role in enhancing strength of the peak-aged alloy. In addition to diffusion and vacancy mechanisms, a Li-rich zone offers a new precipitation pathway for T1 precipitates. Notably, the rapid cooling rate of 16.1 degrees C/s significantly facilitated the formation and inhomogeneous distribution of the cubic & sigma;(Al6Cu5Mg2) phase, which competed with the T1 and S" phases for Cu and Mg atoms. Finally, the formation mechanism of the & sigma; phase under different cooling rates was discussed, and the strengthening and fracture mechanisms were quantified. The present work is expected to enlighten the understanding of the microstructure evolution of Al-Li alloys with varied cast cooling rates.

Microstructure of Zn-Al4 alloy microcastings by micro precision casting based on metal mold

Micro precision casting based on investment casting for micro structures with high aspect ratio

Microstructures and Macrosegregation of Al–Zn–Mg–Cu Alloy Billet Prepared by Uniform Direct Chill Casting

Microstructure Simulation of Zl114a Alloy During Low Pressure Die Casting Process

Microstructure and mechanical properties of Mg–4Al–4Nd–0.5Zn–0.3Mn alloy

Microstructure phase analysis and process optimization of ZL205A metal mold casting

Microstructure evolution and mechanical properties of an ultra-high strength casting Mg–15.6Gd–1.8Ag–0.4Zr alloy

Achieving refined microstructures and improved mechanical properties in a cup-shaped Mg-Gd-Y-Zr alloy casting by novel near-liquidus squeeze cast process

Microstructures and Mechanical Properties of As-Cast and As-Extruded Mg-4.50zn-1.13ca (wt%) Alloys

Characterization of microstructure and nanoscale phase in Mg-15Gd-1Zn (wt.%) alloy fabricated by rotating magnetic field casting

Microstructure Characterization and Mechanical Properties of a Zn and Rare Earth Modified Mg Alloy

Microstructure and Mechanical Properties of As-Cast and Extruded Mg–8Li–3Al–2Zn–0.5Nd Alloy

The microstructure, mechanical properties and creep behavior of Mg–3Sm–0.5Zn–0.4Zr (wt.%) alloy produced by different casting technologies

A novel die-casting Mg alloy with superior performance: Study of microstructure and mechanical behavior

Experiment and Numerical Simulation of Microstructure of ZL114A Alloy in Low Pressure Casting

Microstructure Evolution and Mechanical Properties of a Cast and Heat-Treated Al–Li–Cu–Mg Alloy: Effect of Cooling Rate During Casting

Study on the Microstructure of Mg-4Zn-4Sn-1Mn-xAl As-Cast Alloys

Effect of Casting Process and Zr, V Addition on Microstructure and Mechanical Properties of Al–12Si-4.5Cu–2Ni Alloy

Microstructure Evolution and Strengthening Mechanisms of Cast Al–Cu–Mn Alloy via Ti–Zr-Synergistic Micro-alloying

Study on Microstructure Distribution of Al-Cu-Mg Alloy in Squeeze Casting Process

Effect of Direct Chill Casting Process Parameters on the Microstructure and Macrosegregation of Mg-Al-Zn Ingot