Abstract:The ultra-thin multilayer ceramics capacitors (MLCCs) with layer thickness less than 1 tm are in urgent demand due to the rapid development of modern electronic industries. However, the preparation of the dielectric materials with the desirable grain size <150 nm is a huge challenge. In this work, the ultra-fine BaTiO3 (BT) powders (<120 nm) prepared via solid-state reaction method, hydrothermal method and hydrothermal method following a heat treatment (850 degrees C) are selected to prepare the nano-crystalline non-reducible BT-based ceramics, respectively. The effect of the synthesis methods on the microstructure, electric performance and the reliability of the BT-based ceramics are studied. The results of the Raman, XPS and FT-IR spectroscopy demonstrate that a large number of internal stresses and point defects (hydroxyl/proton defects, Ba vacancies) are existed in the hydrothermal powders and can be eliminated to some extent by a proper heat treatment. Unfortunately, plenty of nano-pores (10-20 nm) are observed in the hydrothermal powders, which cannot be eliminated via the heat treatment or sintering process totally. As a result, the BT-based ceramic prepared by the solid-state powders has an absolute advantage in accelerating aging failure performance, compared to that prepared hydrothermal powders. The TSDC results indicate that the ceramic prepared by the solid-state powders has a lower oxygen vacancy concentration and a higher activation energy. Furthermore, a scaling analysis based on a RC equivalent model identifies the longer oxygen vacancy diffusion time for the ceramic prepared by the solid-state powders. All these features demonstrate that the solid-state ultra-fine BT powders are a promising candidate for the fabrication of the ultra-thin layer MLCCs. (C) 2020 Elsevier B.V. All rights reserved.

Coating of Crystalline BaTiO 3 Layer on Ni Nanoparticles for Multilayer Ceramic Capacitor Electrode

Uniform Coating of BaTiO3–Dy2O3–SiO2 Compound Nano Layer on Ni Particles for MLCC Electrode

Preparation and Characterization of Highly Crystallized BaTiO3layer on Ni Nanoparticles

A novel approach to the preparation of a highly crystallized BaTiO 3 layer on Ni nanoparticles

Preparation of Nano BaTiO3‐Based Ceramics for Multilayer Ceramic Capacitor Application by Chemical Coating Method

Effect of Rare Earth Oxide Content on Nanograined Base Metal Electrode Multilayer Ceramic Capacitor Powder Prepared by Aqueous Chemical Coating Method

Fabrication of Batio3-Based Dielectrics for Ultrathin-Layer Multilayer Ceramic Capacitor Application by A Modified Coating Approach

Preparation of BME MLCC powders by aqueous chemical coating method

Electrical And Reliability Characteristics Of Mn-Doped Nano Batio3-Based Ceramics For Ultrathin Multilayer Ceramic Capacitor Application

Electrode–Ceramic Inter‐Diffusion of Ba(Ti,Zr)O3‐Based Y5V MLCCs with Ni Electrodes

Improved Energy Storage Properties of Fine-Crystalline Batio3 Ceramics by Coating Powders with Al2o3 and Sio2

High Reliable Non-Reducible Ultra-Fine BaTiO3-based Ceramics Fabricated Via Solid-State Method

Dielectric Properties of Batio3-Based Ceramics Sintered in Reducing Atmospheres Prepared from Nano-Powders

Effect of Ho‐Dy Co‐doping on the Electrical Properties and Reliability of BaTiO3‐based Nanoceramics for Base Metal Electrode Multilayer Ceramic Capacitor

Enhancement of Mechanical Properties of Multilayer Ceramic Capacitors through a BaTiO3/polydopamine Cover Layer

Enhancement of Dielectric Properties by Additions of Ni Nano-Particles to A X7r-Type Barium Titanate Ceramic Matrix

Synthesis and electrochemical properties of nanoporous CrN thin film electrodes for supercapacitor applications

Preparation of Nano BaTiO3-Based Dielectric Ceramics by Different Sintering Methods

Interfacial Diffusion Behavior in Ni-Batio3 Mlccs with Ultra-Thin Active Layers

The effects of solid-state and hydrothermal synthesis methods of BaTiO3 on the reliability of multilayer ceramic capacitors

Fabrication of BaTiO 3 nanopowders with high tetragonality via two-step assisted rotary furnace calcination for MLCC applications