Abstract:Electron beam freeform fabrication (EBF3) additive manufacturing technique has been successfully employed to print the non-weldable Al-5Cu thin-walled parts through an optimized set of process parameters. Post-heat treatment is conducted to engineer the desirable microstructure containing multiple nanostructures, i.e., the nanoscale θ" and θ' precipitates, stacking faulted zones and Al-Cu-Cd clusters, leading to a high-strength Al-5Cu alloy with good ductility. The grain formation mechanisms are revealed via a combinatorial simulation and experimentation. It is shown that EBF3 process can produce three different types of grain microstructures: fully equiaxed, fully columnar, and the mixture. In the layerwise melt pool solidification process, wide partially melted zone is observed to favor the formation of equiaxed grains due to its inheritance characteristic. After solution and aging heat treatment, Al-Cu-Cd nanoclusters (∼ 2 nm in Dia.) are generated, which facilitates the formation of nanoscale stacking faulted zones (∼11 nm). Meanwhile, as heterogeneous nucleation sites, Al-Cu-Cd nanoclusters effectively promote θ'-Al2Cu phase (∼ 19 - 114 nm) precipitation to enable the coexistence with fine θ"-Al3Cu precipitates (∼ 7 - 37 nm). The multiscale microstructure, especially incorporating the newly identified nanoscale stacking faulted zones, activates multiple strengthening mechanisms. Consequently, its tensile properties at room temperature reach an ultimate tensile stress of ∼ 496.5 MPa, yield strength of ∼ 435.7 MPa, and elongation of ∼ 9.6%, which are superior to other as-cast and additively manufactured Al-Cu alloys. This work offers a promising processing route to directly fabricate high-strength near-net-shape Al-Cu alloy parts for the aerospace and automotive industries.

Fabrication of high-strength metallic materials with heterostructure prepared via flow control extrusion

Investigation on the Strengthening Mechanism of Flow Control Extrusion by Using Experiment and Numerical Simulation

High Strength and High Ductility Copper Obtained by Topologically Controlled Planar Heterogeneous Structures

Towards enhanced strength-ductility in pure copper by fabricating hetero grain composite laminates

Inherent and Multiple Strain Hardening Imparting Synergistic Ultrahigh Strength and Ductility in a Low Stacking Faulted Heterogeneous High-Entropy Alloy

Enhancing Strength-Ductility Synergy of a Co-Free Complex-Concentrated Alloy Via Tailored Multi-Heterogeneous Microstructure

Additive manufacturing of high strength copper alloy with heterogeneous grain structure through laser powder bed fusion

Mechanical properties and fracture behavior in copper-brass heterostructured fibers

A Simple Approach to Obtaining Enhanced Mechanical Properties of Graphene/copper Composites with Heterogeneous Grain Structures

A dual heterogeneous laminated microstructure design for improving the mechanical properties and electrical conductivity of copper alloys

Achieving Novel Copper–steel Joints with a Combination of High Strength and Ductility Reinforced by In-Situ Fe-rich Particles

Additive Manufacturing of Isotropic-Grained, High-Strength and High-Ductility Copper Alloys

Simultaneous enhancement of strength and ductility by combining heterogeneous microstructure and nanoprecipitates

High Strength and Utilizable Ductility of Bulk Ultrafine-Grained Cu-Al Alloys

Achieving exceptional strength-ductility synergy in a complex-concentrated alloy via architected heterogeneous grains and nano-sized precipitates

Achieving high strength and high conductivity synergy through hierarchical precipitation stimulated structural heterogeneities in a Cu-Ag-Zr alloy

Additively Manufactured Copper Alloy with Heterogeneous Nanoprecipitates-Dislocation Architecture for Superior Strength-Ductility-Conductivity Synergy

A promising structure for fabricating high strength and high electrical conductivity copper alloys

Multiscale microstructure containing nanometer-scale precipitations and stacking faults yields a high-strength Al-5Cu alloy by electron beam freeform fabrication

Enhancing Strength-Ductility Synergy in an Extruded Al-Cu-Li-Mg-Ag Alloy Via Homogeneous GP Zones and Dislocation Configuration

A Powder-Metallurgy-Based Fabrication Route Towards Achieving High Tensile Strength with Ultra-High Ductility in High-Entropy Alloy