Abstract:Lithium-rich layered oxides always suffer from low initial Coulombic efficiency, poor rate capability and rapid voltage fading. Herein, engineering oxygen vacancies in hierarchically Li1.2Mn0.54Ni0.13Co0.13O2 porous microspheres (L@S) is carried out to suppress the formation of irreversible Li2O during the initial discharge process and improve the Li+ diffusion kinetics and structural stability of the cathode mateiral. As a result, the prepared L@S cathode delivers high initial Coulombic efficiency of 92.3% and large specific capacity of 292.6 mA h g−1 at 0.1 C. More importantly, a large reversible capacity of 222 mA h g−1 with a capacity retention of 95.7% can be obtained after 100 cycles at 10 C. Even cycled at ultrahigh rate of 20 C, the L@S cathode can deliver stable reversible capacity of 153 mA h g−1 after 100 cycles. Moreover, the full cell using L@S as cathode and Li4Ti5O12 as anode exhibits a relatively high reversible capacity of 141 mA h g−1 with an outstanding voltage retention of 97% after 400 cycles at a large current density of 3 C. These results may shed light on the improvement of electrochemical performances of lithium-rich layered oxides via the multiscale coordinated design based on atomic defects, microstructure and composition.

Facile oxidant-assisted treatment to improve the cyclic performance of Li-rich cathode materials

Enhancing high-voltage performances of nickel-based cathode material via aluminum and progressive concentration gradient modification

Improvement of cyclicability through precursor treatment in Ni-rich cathode materials

Mitigation of Cation Mixing of LiNiO2-based Cathode Materials by Li-doping for High-Performing Lithium-Ion Battery

Engineering oxygen vacancies in hierarchically Li-rich layered oxide porous microspheres for high-rate lithium ion battery cathode

Enhanced Electrochemical Performance of LiNi0.8Co0.1Mn0.1O2 Cathode for Lithium-Ion Batteries by Precursor Preoxidation

Surface Coating with Li-Ti-O to Improve the Electrochemical Performance of Ni-rich Cathode Material

Improving the Cycling Performance of the Layered Ni-Rich Oxide Cathode by Introducing Low-Content Li2mno3

Lattice Oxygen Redox Reversibility Modulation in Enhancing the Cycling Stability of Li‐Rich Cathode Materials

Pre-Lithiation of Li(Ni1-x-yMnxCoy)O2 Materials Enabling Enhancement of Performance for Li-Ion Battery.

Enhancing the electrochemical performance of Li-rich cathode material by a flexible precursor treatment method

Improvement of the cyclic deterioration and structural evolution of Li[Li0.2Ni0.2Mn0.6]O2 cathode material by controlling initial charging voltages

Improving electrochemical performances of Lithium-rich oxide by cooperatively doping Cr and coating Li3PO4 as cathode material for Lithium-ion batteries

Enhanced Stability of Vanadium-Doped Li1.2Ni0.16Co0.08Mn0.56O2 Cathode Materials for Superior Li-ion Batteries

Manipulating the Electronic Structure of Li‐Rich Manganese‐Based Oxide Using Polyanions: Towards Better Electrochemical Performance

Improving electrochemical performances of Lithium-rich oxide by cooperatively doping Cr and coating Li<sub>3</sub>PO<sub>4</sub> as cathode material for Lithium-ion batteries

Suppressing Voltage Fading of Li‐Rich Oxide Cathode via Building a Well‐Protected and Partially‐Protonated Surface by Polyacrylic Acid Binder for Cycle‐Stable Li‐Ion Batteries

Building the Stable Oxygen Framework in High‐Ni Layered Oxide Cathode for High‐Energy‐Density Li‐Ion Batteries

Enhancing the Reversibility of the Chemical Evolution of the Ni-rich LiNi0.8Co0.1Mn0.1O2 Cathode Via a Simple Pre-Oxidation Process.

Synergistic Enhancement Effect of Al Doping and Highly Active Facets of LiMn2O4 Cathode Materials for Lithium-Ion Batteries

A Redox Couple Strategy Enables Long‐Cycling Li‐ and Mn‐Rich Layered Oxide Cathodes by Suppressing Oxygen Release