Abstract:Lithium-rich layered oxides have attracted much attention due to their high discharge capacity (>250 mA h·g–1). However, lithium-rich layered cathodes suffer from poor rate capabilities and voltage decay, which seriously limit their practical application. Herein, a unique @spinel double-spinel shell heterostructure is designed and successfully synthesized via coprecipitation and high-temperature solid-phase methods. In particular, lithium-rich layered oxides show good rate capabilities and high capacity retention when the molar amount of cobalt acetate and manganese acetate is 5%. After 100 cycles at 0.2 C, a discharge capacity of 232 mA h g–1 and a capacity retention of 92.7% can be obtained. The superior electrochemical performance of the in situ-transformed Li-rich layered cathode can be attributed to the unique three-dimensional diffusion channels for Li ions of the surface spinel phase. Besides, the in situ-transformed LiCoMnO4 shell can also improve the structural stability of the Li-rich layered oxides by reducing the side reactions and protecting the material from being corroded by the electrolyte. This study provides a strategy for surface modification, which can effectively improve the electrochemical performance of Li-rich layered cathode materials with high performance.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsaem.1c01955.SEM image of the precursor Ni1/6Co1/6Mn4/6CO3 and the corresponding mapping spectrum; ex situ XRD spectra of the LLO and LSS-0.05 samples; EDS line scan of the selected area and the corresponding HTEM diagram of the LSS-0.05 sample; CV and dQ/dV curves of the first three cycles of the LLO, LSS-0.05, and LSS-0.1 samples; initial charge and discharge curves of LiCoMnO4, LSS-0.2, and LSS-0.4 samples; discharge curves of LLO, LSS-0.05, and LSS-0.1 samples at different rates and with different cycles; typical single titration curve of GITT measurements; equivalent circuit of half-cells; and EIS spectra of LLO, LSS-0.05, and LSS-0.1 samples in the initial cycle (PDF)This article has not yet been cited by other publications.

A novel surface modification strategy for Li-rich Mn-based layered oxide cathodes of high-capacity and high-cyclic stability by an additive of LiBH<sub>4</sub> to the electrolyte

Surface Modification and Electrochemical Properties of Li-Rich Layered Cathode Materials for Lithium-Ion Batteries

Multifunctional surface structure with enhanced electron and ion conductivities for superior electrochemical performance of Co-free Li-rich Mn-based layered oxide cathodes

Multifunctional Surface Construction for Long-Term Cycling Stability of Li-Rich Mn-Based Layered Oxide Cathode for Li-Ion Batteries

Improvement of the Cycling Stability of Li-Rich Layered Mn-Based Oxide Cathodes Modified by Nanoscale LaPO4 Coating

Significant Enhancement of the Capacity and Cycling Stability of Lithium-Rich Manganese-Based Layered Cathode Materials via Molybdenum Surface Modification

Lithium-rich manganese-based cathode materials with highly stable lattice and surface enabled by perovskite-type phase-compatible layer

Surface structure regulation toward anionic redox activation of Li1.20Mn0.533Ni0.133Co0.133O2 cathodes with high initial coulombic efficiency

One-pot synthesis and multifunctional surface modification of lithium-rich manganese-based cathode for enhanced structural stability and low-temperature performance

Lewis Acidity Organoboron‐Modified Li‐Rich Cathode Materials for High‐Performance Lithium‐Ion Batteries

Enhancing the Stability of Li-Rich Mn-Based Oxide Cathodes Through Surface High-Entropy Strategy

2-mercaptobenzothiazole as a surface modifier to improve the electrochemical properties of Li1.2Ni0.2Mn0.6O2 cathode materials

Reinforcing the Stability of Cobalt-free Lithium-rich Layered Oxides via Li-poor Ni-rich Surface Transformation

Sulfuration of Li‐Rich Mn‐Based Cathode Materials for Multianionic Redox and Stabilized Coordination Environment

Improving the Cycling Stability of Li-Rich Mn-Based Cathodes through Surface Modification of VOPO 4

Improving the Cycling Stability of Li-Rich Mn-Based Cathodes Through Surface Modification of VOPO4

Improving the Electrochemical Performance of a Lithium-Rich Layered Cathode with an In Situ Transformed Layered@Spinel@Spinel Heterostructure

In-situ formation of Li0.5Mn0.5O coating layer through defect controlling for high performance Li-rich manganese-based cathode material

Optimizing Both Bulk and Surface Structure of Li‐Rich Layered Cathodes for Long‐Life and Safe Li‐Ion Batteries

Surface Heterostructure Induced by PrPO4 Modification in Li1.2[Mn0.54Ni0.13Co0.13]O2 Cathode Material for High-Performance Lithium-Ion Batteries with Mitigating Voltage Decay.

Delocalized Li@Mn6 Superstructure Units Enable Layer Stability of High-Performance Mn-rich Cathode Materials