Abstract:To further improve the thermal shock resistance and ablation resistance of SiBCN system ceramics targeted much harsh environment, both ultra-high temperature ceramic phases and carbon fibers are expected to be incorporated simultaneously as the reinforcements. However, tough problems like difficulty in densification as well as degradation of C fibers (Cf) due to interfacial reaction usually cannot be avoided. Thus, in this study, Zr as well as chopped Cf with BN coating were introduced into SiBCN ceramics by mechanical alloying and after hot-pressing sintering to prepare C/SiBCNZr composites. The structure and phase component development have been characterized in detail by XRD, SEM, TEM and XPS etc., and mechanical properties, fracture behavior and toughening mechanisms were also investigated. Zr-B and Zr-O bonds are detected besides Si-C, N-B and N-B-C bonds when pre-alloyed ZrB2 amorphous powder was incorporated into SiBCN system by further mechanical-alloying treatment. After hot-pressing, the ultra-high temperature phases of ZrB2 and ZrN were formed as expected besides the original matrix phases of BN(C) and SiC. Excellent mechanical properties can be obtained for SiBCNZr ceramic. The BN coating on carbon fibers successfully avoids the severe fiber degradation and makes it possible for moderating strong interface bonding, which ensuring the debonding, crack deflection, fiber pulling-out and bridging during the fracture. As a result, the C/SiBCNZr composites retain good mechanical properties and fractures in a pseudoplastic fracture manner, showing better potential applications in harsh environments. Optimization of the BN coating on Cf and Zr incorporation by pre-mechanical alloying can be a good route to achieve Cf/SiBCNZr composites with a better balance between thermal shock resistance, ablation resistance and mechanical properties.

Interface characteristics in ZrB2-based ceramics containing SiC and/or ZrC particles via hot-pressing sintering

A TEM study of nanostructures and interfaces in the hot-press sintered ZrB2–SiC–Si3N4 composites

Novel (Zr, Ti)B2-(Zr, Ti)C-SiC ceramics via reactive hot pressing

Effects of SiC Platelet and ZrSi2 Additive on Sintering and Mechanical Properties of ZrB2-based Ceramics by Hot-Pressing

Effect of Zr on the solid sintering process of SiBCN ceramics: Diffusion couple method experiment and DFT calculation

Preparation and Mechanical Properties of ZrB2-based Ceramics Using MoSi2 As Sintering Aids

Mechanical Properties of ZrB<sub>2</sub>-Based Ceramics Reinforced by Nano-SiC Whiskers

Effect of ZrB2 and its oxide impurities (ZrO2 and B2O3) on hot-pressed Si3N4 ceramics at low temperature

Effect of ZrB2 powders on densification, microstructure, mechanical properties and thermal conductivity of ZrB2-SiC ceramics

Effects of Zr and chopped C fiber on microstructure and mechanical properties of SiBCN ceramics

Effect of Carbon Impurities on Hot-Pressed Zrb2-Sic Ceramics

Effect of sintering temperature and holding time on the microstructure and mechanical properties of ZrB2–SiCw composites

Pressureless Sintering of Silicon Carbide Ceramics Containing Zirconium Diboride

Preparation, mechanical properties, and toughening mechanisms of SiCw/SiCp‐reinforced zirconia‐toughened alumina ceramics

Monolithic ZrB 2 ‐based UHTC s using polymer‐derived Si(Zr,B)CN as sintering aid

Effect of Si/Zr molar ratio on the sintering and crystallization behavior of zircon ceramics

Effect of Nano SiC on Microstructure and Mechanical Properties of BN-ZrO2-SiC Multiphase Ceramics

The impact of Si3N4 incorporation on the mechanical characteristics of ZrB2-SiC nanocomposite sintered via pressureless method

Effects of ZrB2 powders on microstructure and mechanical properties of ZrB2-SiCw ceramics

Microstructure And Mechanical Properties Of Zrb2-Based Composites With Laminated Structure

Microstructure, Mechanical, and Thermal Properties of in Situ-Synthesized (zrb2+sic)/zr2[al(si)]4c5 Composites