Abstract:The five‐phase six‐leg inverter is adopted for the fault‐tolerant control of the five‐phase PMSM, which can relieve the constraint of the zero neutral point current and improve the performance of the machine. The maximum torqu MT and MC current regulations are considered under different open‐circuit conditions, and their effectiveness are verified by the experiments. Five‐phase permanent magnet synchronous machine (PMSM) can operate under open‐circuit faults with the appropriate current regulations. However, the traditional current regulations based on the five‐phase half‐bridge inverter have to satisfy the constraint of zero neutral point current, which limits the fault‐tolerant performance of the machine. Thus, this paper investigates the current regulation based on the five‐phase six‐leg (FPSL) inverter, which relieves the zero‐neutral point current limitation, and both current regulations considering the maximum torque (MT) and minimum copper loss (MC) are derived under different open‐circuit conditions. The cost of the system has increased, but with the new regulations, better fault‐tolerant operation capability of the machine can be obtained under all kinds of open‐circuit faults. Moreover, with the introduction of the neutral point current, the machine can work under triple‐phase open‐circuit faults. In conclusion, the proposed control scheme based on the FPSL inverter expands the fault‐tolerant operation capability of the five‐phase PMSM. The experiment results prove the effectiveness of the proposed current regulation on increasing average torque or reducing copper loss under fault‐tolerant operation.

A Boost-Type Four-Leg Inverter With Integrated Open-Phase Fault-Tolerance for PMSM Drives

A Fault Tolerant Control Strategy for Dual Three-Phase PMSM under Single-Phase Open Circuit Fault Considering Inductance Asymmetry

Fault-Tolerant Control of Dual Three-Phase PMSM Based on Minimum Copper Loss under Multi-Phase Open and Open-Switch Faults

Single- and Two-Phase Open-Circuit Fault Tolerant Control for Dual Three-Phase PM Motor Without Phase Shifting

Fault Tolerant Control of Harmonic Injected Nine-Phase Flux Switching Permanent Magnet Motor Drive System

Adaptive Torque Ripple Suppression Methods of Three-Phase PMSM During Single-Phase Open-Circuit Fault-Tolerant Operation

Fault-Tolerant Control Strategy with Asymmetric Phase Currents for Single to Four-Phase Open-Circuit Faults of Six-Phase PMSM

Fault-tolerant Control Strategy with Reduced Switching Frequency for Inverter-Based Fault in Open-Winding PMSM System

Fault‐tolerant operation for five‐phase permanent magnet synchronous machine drives with five‐phase six‐leg inverter

Fault-Tolerant Control of Five-Phase Induction Motor under Single-Phase Open

Compatible Phase Current Reconstruction Scheme for Fault-Tolerant Five-Leg Dual-Inverter Fed Open–Winding Permanent Magnet Synchronous Motor

Open-Circuit Fault-Tolerant Control of a Six-Phase Asymmetric Permanent Magnet Synchronous Motor Drive System

Inverter Reconstruction Approach for Open-End Winding Five-Phase PMSM With Pattern-Based Vector Synthesis and Hybrid SVPWM Modulation

Simplified PWM for Fault Tolerant Control of Open Winding PMSM Fed by Hybrid Inverter

Fault Tolerant Control of a Multiphase Motor with Non-Sinusoidal Source under Open-Phase Conditions

Fault Tolerant Inverter Based Direct Torque Control for Permanent Magnet Synchronous Motor

An Embedded Fault-Tolerant Control Method for Single Open-Switch Faults in Standard PMSM Drives

A Novel Two-Mode Inverter Based Open-Winding PMSM Drive and Its Modulation Strategies

Hybrid Modulation Fault-Tolerant Control of Open-End Windings Linear Vernier Permanent-Magnet Motor with Floating Capacitor Inverter

Diagnosis of Open-Phase Faults for a Five-Phase PMSM Fed by a Closed-Loop Vector-Controlled Drive Based on Magnetic Field Pendulous Oscillation Technique

A fault-tolerant operation method of PMSM fed by cascaded two-level inverters