Abstract:The intermediate temperature deformation behavior and microstructural evolution of a spray formed 7075 Al alloy were performed at temperatures 60–120 °C with strain rates 0.00001–0.1 s −1 . The results reveal that the softening mechanism of the intermediate temperature deformation is dynamic recovery (DRV), which can be quantitated by Zener-Hollomon ( Z ) parameter. The constitutive equation can reasonably predict the stress-strain behavior of the alloy at intermediate temperatures. The activation energy is related to the deformation process and the interactions of the substructure, the average value is 140.1 kJ/mol. The higher efficiency of power dissipation in the processing map is related to the DRV at lower deformation temperatures. The optimum processing domain is located at the temperature of 90–120 °C and strain rate of 0.006–0.1 s −1 with a power dissipation efficiency range of 20%–40%. The processing parameters of the intermediate temperature deformation should be strictly controlled according to the strain. The uniform microstructure of 7075 alloys obtained by spray forming is crucial to overcome the disadvantage of poor deformability. The inferior coordinated deformation facilitates crack propagation at low strain rates. The high-density dislocation provides adequate nucleation sites for dynamic precipitation. The level of dynamic restoration facilitates the transformation from low angle grain boundaries (LAGBs) to high angle grain boundaries (HAGBs). The dislocations move to the grain/sub-grain boundary to form dislocation walls at low temperatures. The contribution to the stress from grain boundary (13.2–17.7 MPa), nanoscale precipitates (65.7–191.5 MPa), and dislocation (5.9–23.4 MPa) increases the difficulty of deformation. The deformation process at higher temperatures (105–120 °C) can be facilitated by the dissolution and coarsening of the nanoscale precipitates, and dislocation motion at the grain boundary.

Grain refinement and high strengthening of 7075 aluminum alloy by high-pressure sliding

Strengthening of A5052 aluminum alloy by high-pressure sliding process

The Evolvement of Mechanical Properties and Microstructure of Commercial Aluminum Alloy 6061 via High-Pressure Torsion

Strength enhancement of an aluminum alloy through high pressure torsion

Mechanical Behavior and Strengthening Mechanisms in Precipitation-Strengthened Aluminum Alloy with Gradient Structure Induced by Sliding Friction Treatment

Achieving highly strengthened Al-Cu-Mg alloy by grain refinement and grain boundary segregation

Deformation Behavior and Mechanical Properties of AA7075 During Pre-hardened Aluminum Alloy Hot Forming Process

Enhanced formability and accelerated precipitation behavior of 7075 Al alloy extruded rod by high temperature aging

Effects of High Pressure Heat Treatment on Microstructure and Mechanical Properties of Aluminum Bronze

High pressure induced precipitation in Al7075 alloy

Achieving superior strength and ductility in 7075 aluminum alloy through the design of multi-gradient nanostructure by ultrasonic surface rolling and aging

Microstructure and Properties Evolution of 7075 Al alloy in Hot Rolling and Short Process Heat Treatment

Hot tensile deformation behavior and microstructure evolution of 7075 aluminum alloy sheet

Point Defect Clusters Induced by High-Speed Deformation and its Effect on Age-Hardening in 6061 Aluminum Alloys

Intermediate temperature tensile behavior and processing map of a spray formed 7075 aluminum alloy

Creep Resistance of S304H Austenitic Steel Processed by High-Pressure Sliding

Evolution of Microstructure and Mechanical Properties of an As-Cast Mg-8.2gd-3.8y-1.0zn-0.4zr Alloy Processed by High Pressure Torsion

Requirements for Processing High-Strength AlZnMgCu Alloys with PBF-LB/M to Achieve Crack-Free and Dense Parts

Nanostructure and related mechanical properties of an Al-Mg-Si alloy processed by severe plastic deformation

Investigation on strengthening of 7075 aluminum alloy sheet in a new hot stamping process with pre-cooling

Mechanical Property and Microstructure of Rolled 7075 Alloy under Hot Compression with Different Original Grains