Abstract:Excellent strain hardening capabilities are known to be the unique strategies to hold the key towards a good strength-ductility balance in Al − base composites. Herein, in-situ Fe-aluminide (FeAl) reinforced Al − matrix composites (Al/Fe-aluminide) were fabricated by a twostep thermal processing method: sintering (900 °C/1 h), and uniaxial forging (400 °C, deformation up to 20 % ). The reinforcements were formed in-situ by the exothermal reaction between the host Al matrix and Fe2O3 nanoparticles during sintering Measured strain rate sensitivity ( m = 0.035)and strain rate recovery rate ( η r ) highlighted that deformation during forging enhances strain hardening ability of the composites. Comprehensive characterization reveals high density of geometrically necessary dislocation ( ρ G ∼ 1 × 10 15 m − 2 ) usually persists near the grain boundaries (GBs) and the triple junctions of highly textured FCC − Al grains. Microtextural and Kernel average misorientation (KAM) measurements highlighted existence of strong deformation texture of Bras { 110 } < 112 > and Goss { 110 } < 001 > 2 in FCC − Al matrix induce strong resistance to plastic deformation. While nanoindentation response based on plastic flow corresponding to activation volume ( V * ∼ 42 b 3 ) revealed that activities of GB interface − dislocation interaction induced strain accumulation at the FCC − Al GB interface zones involved in a thermally activated process promotes the evolution of ρ G distribution during straining sustain larger strains. The results reveal that the simultaneous attainment of both these processes improves global strain hardening behavior which is advantageous for the enhancement of resistance to failure.

Nanostructure and related mechanical properties of an Al-Mg-Si alloy processed by severe plastic deformation

Nano-scale Reinforcements and Properties of Al-Si-Cu Alloy Processed by High-Pressure Torsion

The nanoscale mechanisms of strengthening and ductility enhancement in an Al–Mg–Si–Mn alloy on processing by high-pressure torsion

Microstructure and Mechanical Properties of Al-4Mg-0.3Cu Alloy after HPT and Postdeformation Annealing

Microstructure Evolution during High-Pressure Torsion in a 7xxx AlZnMgZr Alloy

Evolution of microstructure and texture during severe plastic deformation of the aluminium alloy AA2099

Improved Tensile Ductility by Severe Plastic Deformation for Nano-Structured Metallic Glass.

The Evolvement of Mechanical Properties and Microstructure of Commercial Aluminum Alloy 6061 via High-Pressure Torsion

Effects of Severe Plastic Deformation and Subsequent Annealing on Microstructures of a Ni50.6Ti49.4 Shape Memory Alloy

Achieving highly strengthened Al-Cu-Mg alloy by grain refinement and grain boundary segregation

Severe Plastic Deformation of Light Metals (Magnesium, Aluminum and Titanium) and Alloys by High-Pressure Torsion: Review of Fundamentals and Mechanical/Functional Properties

Microstructures and Mechanical Properties of a Nanostructured Al-Zn-Mg-Cu-Zr-Sc Alloy under Natural Aging

Microstructural evolution and mechanical properties of biomedical Co-Cr-Mo alloy subjected to high-pressure torsion

Microstructure and mechanical properties of Al-Mg-Si alloy during solution heat treatment and forging integrated forming process

Severe plastic deformation of two-phase TiNiCuNb shape memory alloy

Strength enhancement of an aluminum alloy through high pressure torsion

Atomic Structure of Ti2NiCu Alloy after Severe Plastic Deformation by High Pressure Torsion and Heat Treatment

Approaching 1 GPa ultra‐high tensile strength in a nanostructured Al‐Zn‐Mg‐Cu‐Zr‐Sc alloy prepared by severe plastic deformation

Achieving high strain rate superplasticity in an Al-Cu-Li alloy processed by thermo-mechanical processing

Improving strain hardening behavior in nano-intermetallic reinforced aluminum in-situ composites through an optimized twostep thermal processing method; sintering and uniaxial forging

The Evolutions of Microstructure, Texture and Hardness of A1050 Deformed by HPT at the Transition Area