Abstract:In this paper, we tested the mechanical properties at room and high temperatures, and compared the cutting performance of three ceramic tool materials with different components added sequentially. By analyzing and comparing, the influence of material components on the changes in material mechanical properties and cutting performance is obtained, and the guidance for material system design is proposed. Three kinds of Si3N4‐based ceramic tools (single‐phase Si3N4, Si3N4/(W,Ti)C, and Si3N4/(W,Ti)C/Ni) were fabricated by microwave sintering. The phase composition, toughening mechanism, mechanical properties at room and high temperatures (800°C), and cutting performance of Si3N4‐based ceramic tool materials with different additives were investigated. The results showed that the addition of (W,Ti)C and Ni had a significant effect on improving the mechanical properties at room temperature, although it reduced the phase transition conversion rate of Si3N4. Si3N4/(W,Ti)C tools had good high‐temperature stability, while Si3N4/(W,Ti)C/Ni tools had a decrease of about 31.6% in high‐temperature hardness and a decrease of 13.7% in high‐temperature flexure strength. Under the premise of ensuring a certain level of fracture toughness, high‐temperature hardness is the main influencing factor on the cutting life of cutting tools. The Si3N4/(W,Ti)C tools exhibit superior cutting performance whose cutting life reaches to 50.67 min which was 1.37–3.27 times longer than the other two ceramic cutting tools at the same cutting parameters when continuous dry cutting T10A. In addition, high‐temperature flexure strength limits the choice of cutting speed, and lower high‐temperature flexure strength can lead to rapid tool failure.

Thermal Conductivity of Cutting Tool Ceramics Fabricated from Exothermal Mixtures of Cr2O3–AlN and ZrO2(M)–Al–C via Hot Pressing

Enhanced Performance in Si3N4 Ceramics Cutting Tool Materials by Tailoring of Phase Composition and Hot-Pressing Temperature

Temperature distribution near cutting edge of ceramic cutting tools measured by thermal video system

The Computer Simulation of the Temperature Distribution on the Surface of Ceramic Cutting Tools

Preparation of Al2O3/Ti(C,N)/ZrO2/CaF2@Al(OH)3 Ceramic Tools and Cutting Performance in Turning

Friction Comparison and Wear Analysis of Ceramic Cutting Tools Made from Alumina-Zirconia- Chromia Content

Thermobarrier and antifriction properties of triboceramics on the surface of a cutting tool with (TiAlCrSiY)N/(TiAlCr)N coating during high-speed dry cutting

Calculational and Experimental Investigation into the Thermal Conductivity of Materials of Ceramic Casting Molds. I. Experiment

Numerical Simulation of the Al2O3/ZrO2 (Y2O3) Ceramic Cutting Tool During Cutting Process's Temperature Fields and Stress Fields

Characterization of hot‐pressed ZrC–TiC composites

Effect of SiC Addition to Al2O3 Ceramics Used in Cutting Tools

Mechanical and Thermal Properties of Antiperovskite Ti3alc Prepared by an in Situ Reaction/Hot-Pressing Route

Effects of AlN Content and Sintering Atmospheres on the Thermal Conductivity of Hot-Pressed SiC Ceramics

Thermal Conductivity of Investment Casting Ceramics

The influence of zirconium dioxide nanoadditives on the properties of mullite-corundum

Thermoelectric Characteristics of the Process of Steel Turning by Carbide Inserts with Combined Coatings

Tribological Properties of Hot Pressing Alumina Matrix Ceramic Materials Improved by Zr-O-B Compounds

Mechanical properties of ZrB2/SiC/WC ceramic tool materials from room temperature to 1100 °C and cutting performance

Comparative experimental study on application feasibiility of MTCVD TiCN-Al2O3-TiOCN multi-layer coated carbide and PVD TiN single layer coated composite ceramic inserts during dry machining of Ti-6Al-4V

The influence of components on the high‐temperature performance and cutting performance of Si3N4‐based ceramic tools

Synthesis and Mechanical Properties of High-Purity Cr2alc Ceramic