Abstract:ZrO 2 ceramics are commonly known as 'hard and brittle' materials due to their exceptional properties, such as high hardness, heat resistance, chemical stability, and low thermal conductivity. However, the hole processing technique for ZrO 2 ceramics often results in significant tool wear and compromises the quality of the holes. This study investigates the removal mechanism of ZrO 2 ceramic materials by using carbide tools, diamond-coated carbide tools, and micro-sintered tools. It also analyzes the impact of processing parameters on the wear mechanism of different tools and the quality of hole processing in ZrO 2 ceramics. The findings revealed that at high spindle speed (8000 r/min) and low feed rate (1 mm/min), the diamond coating on the rake surface of the diamond-coated carbide tool tends to peel off, leading to the formation of sharp edges on the flank surface. This phenomenon results in a reduction in thrust forces. Moreover, it is observed that as the number of hole machining operations increases, the peeling of the diamond coating on the tool flank becomes more severe. The increase in feed rate causes the diamond coating peeling area on the rake face of the tool to expand toward the chisel edge and even reach the thinned edge area near the chisel edge. When the feed rate of carbide tools increases, the wear degree of the chisel edge gradually increases, while the wear degree of the main cutting edge corner position gradually decreases. At low spindle speeds, the main cutting edge breaks and the cutter head is also damaged and deformed. The main wear mechanisms of micro-sintered tools involve shedding, fragmentation, wear, and adhesion of diamond abrasive grains. The bottom surface of the tool tends to accumulate a significant amount of flaky adhesion, which dulls the tool and increases thrust force. In contrast to carbide tools, diamond-coated carbide tools offer improved hole exit quality. However, micro-sintered tools often exhibit large volumes of flaking at the hole exits, resulting in shell-like stripes on the peeled surface.

Friction Comparison and Wear Analysis of Ceramic Cutting Tools Made from Alumina-Zirconia- Chromia Content

Analysis of Material Removal in Alumina Ceramic Honing

Preparation of Al2O3/Ti(C,N)/ZrO2/CaF2@Al(OH)3 Ceramic Tools and Cutting Performance in Turning

Study on the Orthogonal Cutting Process of Al7050T7451 with Uncoated and Coated Tools

Preparation of Ultra-Fine ATC Ceramics and Analysis of Its Dry-Sliding Wear Behavior

A comparative study on tribological behavior of Al2O3, AlN, Si3N4 and ZrO2 ceramics sliding against polycrystalline diamond ball

Influence of self-lubricating elements (SrSO4, Mo, and CaF2) on machining performance of Al2O3-ZrO2 (Y2O3)-NiCr-Ag cutting tool over a wide cutting speed range

Friction and wear behaviors of Al 2 O 3 /TiC micro-nano-composite ceramic sliding against metals and hard materials

A Study of Parameters Affecting Wear Resistance of Alumina and Yttria Stabilized Zirconia Composite Coatings on Al-6061 Substrate

A Study on the Development of a Composite Ceramic Tool ZrO2/(W, Ti)C and Its Cutting Performance

Wear Mechanisms and Notch Formation of Whisker-Reinforced Alumina and Sialon Ceramic Tools during High-Speed Turning of Inconel 718

Three-body Abrasive Wear Resistance of Iron Matrix Composites Reinforced with Ceramic Particles

Fabrication and Abrasive Wear Behavior of ZrO2-SiC-Al2O3 Ceramic

Tribological Behavior and Cutting Performance of Monolayer, Bilayer and Multilayer Diamond Coated Milling Tools in Machining of Zirconia Ceramics

Forecasting the Friction Coefficient of Rubbing Zirconia Ceramics by Titanium Alloy

Dry Sliding Wear Behaviour of Al<sub>2</sub>O<sub>3</sub>-Cr<sub>2</sub>O<sub>3</sub> Coatings with Different Contents of Cr<sub>2</sub>O<sub>3</sub>

Comparative study of tool wear mechanisms in drilling ZrO2 ceramics using various tool types

Microstructure and High Temperature Friction and Wear Properties of Nanostructured ZrO2(Y2O3)-Al2O3 Ceramics

Dependence of Tribological Characteristics on Mechanical Properties and Phase Transformations of Zirconia-Based Composite Ceramics

Unlubricated Sliding Wear Mechanism of Fine Ceramics Al2O3 and ZrO2 Against High Chromium Cast Iron

Interfacial characterization and erosive wear performance of zirconia toughened alumina ceramics particles reinforced high chromium white cast irons composites