Abstract:Abstract The active practical application of materials based on cubic zirconium dioxide (c-ZrO2) for catalysis, luminescence, and sorption of heavy metals demands the development of methods for its preparation in a nanostructured form. In this work, nanoparticles of undoped cubic zirconia were obtained by solution combustion method, the features of their structure and morphology were investigated, and the efficiency of their use as a basis for sorbents for the removal of hexavalent chromium Cr(VI) from aqueous solutions was evaluated. Based on XPS, it was established that the stabilization of the high-temperature cubic phase of c-ZrO2 occurred due to multiple oxygen vacancies which were formed during the synthesis by glycine-nitrate combustion. The results of PXRD and Raman spectroscopy confirmed the cubic structure of the obtained zirconium dioxide nanoparticles, the average crystallite size was approximately 2 nm. Adsorption structural analysis and SEM indicated aggregation of c-ZrO2 nanocrystals into primary (45-95 nm) and secondary (submicron) agglomerates. The specific BET surface of the nanocrystals was 25.4 m2/g, the pore volume was 0.1670 cm3/g, the major part of which is associated with interparticle porosity. Using kinetic pH-metry, it was found that on the surface of synthesized c-ZrO2, rapidly hydrated aprotic Lewis acid centers predominated, and the point of zero charge (PZC) was 6.33. The results of Cr(VI) sorption from aqueous solutions with concentrations varying from 0.25 to 1.25 mmol/L were described by the Freundlich isotherm (R2 = 0.971), which corresponds to the multilayer adsorption. The maximum adsorption capacity according to Langmuir was 33 mg/g or 1.34 mg/m2 per unit area. These results allow us to consider the obtained undoped zirconium dioxide as a promising base for sorbents of heavy metals.

Preparation of zirconium metal through electrolysis of zirconium oxycarbonitride anode

Deposition of Y2O3 stabilized ZrO2 thin films from Zr(DPM)4 and Y(DPM)3 by aerosol-assisted MOCVD

Preparation and Application of a NaCl-KCl-CsCl-Cs2ZrCl6 Composite Electrolyte

Review—Preparation of Zirconium Metal by Electrolysis

Processing of Zirconium Oxide Raw Materials to Produce Zirconium Silicides via Electrolysis of KCl-K2SiF6-ZrO2 Melt

Electrochemical Studies on the Redox Behavior of Zr(IV) in the LiCl-KCl Eutectic Molten Salt and Separation of Zr and Hf

Preparation of Titanium Metal by Deoxygenation Under KCl-NaCl-YCl3 System Using Soluble Anode

Preparation of zirconium coating on zirconium-niobium alloy substrate by pulsed current electrodeposition from fluoride molten salt

Preparation and SEM of Ni/Ce-YSZ Anode Materials

Ionothermal Synthesis and Characterization of Crystalline Zirconium Phosphate from Oxalic Acid/Tetrapropyl Ammonium Bromide System

Preparation of Zirconia Powders by Sol-gel Process

One-step combustion synthesis of undoped c-ZrO2 for Cr(VI) removal from aqueous solutions

Ductile Zirconium from Zircon Sand

Preparation Of Nanocrystalline Zirconium Carbide Powders By Carbothermal Reduction

A Novel Method for Preparing Anode Cermets for Solid Oxide Fuel Cells

Preparation of a high surface area zirconium oxide for fuel cell application

Zirconium Oxide for PEFC Cathodes

Study on a new, environmentally benign method and its feasibility of preparing nanometer zirconia powder

Electrocatalytic Oxygen Reduction Using Metastable Zirconium Suboxide

Simple Preparation of Yttria‐Stabilized Zirconia Powders by Plasma Discharge Electrolysis in Nitrate Solution

Computational model‐based design of molten salt electrorefining process for high‐purity zirconium metal recovery from spent nuclear fuel