Abstract:A novel one-step liquid plasma-assisted particle deposition and sintering (LPDS) method is used to prepare a ZrC–ZrO2 nanocomposite ceramic coating on a TiAlNb medium-entropy alloy to enhance its ablation resistance. For comparison, a conventional plasma electrolytic oxidation (PEO) ceramic coating is fabricated on a substrate without ZrC particles. Results show that numerous ZrC particles are introduced into the coating, accompanied by partial oxidation to ZrO2 during the LPDS. The thickness of the nanocomposite coating increases significantly by approximately 11.4 times compared with that of the PEO coating. At 1000 °C, the ablation thickening of the ZrC–ZrO2 nanocomposite coating is approximately 1/4 of that of the substrate after ablation in air. Moreover, 17.88% and 2.83% of the substrate surface and PEO coating are peeled, respectively, whereas no peeling occurred in the ZrC–ZrO2 nanocomposite coating. This can be attributed to the high melting point and exceptional toughness of ZrO2, which allow it to absorb the stress caused by thermal shocks and inhibit crack formation. A thick nanocomposite coating is crucial for protecting the substrate by preventing oxygen from permeating the coating and oxidizing the substrate. Additionally, the glass phase of SiO2 densifies the pores and cracks in the coating, thereby significantly inhibiting the inward diffusion of oxygen and preventing ablation. Therefore, LPDS is a novel strategy for designing and fabricating multifunctional coatings to enhance the thermal protection of alloy substrates via the incorporation of various functional particles.

Ablation behavior of a network interlacing ZrC-VC ceramic coating prepared by a pioneering spillover permeation

Preparation and long-term ablation behavior of Cf-reinforced ZrC-SiC coated C/C-ZrC-SiC composite

Anti-ablation performance of plasma sprayed ZrB 2 /SiC coatings on C/C substrates and the influence of a chemical vapor deposited SiC interlayer

Enhanced ablation resistance of ZrC–ZrO2 nanocomposite ceramic coating on TiAlNb medium-entropy alloy prepared by a novel strategy

Anti-ablation Performance of Plasma Sprayed ZrB2/SiC Coatings on C/C Substrates and the Influence of a Chemical Vapor Deposited SiC Interlayer

Ablation behavior of C/C-ZrC-SiC composite with gradient distribution of ZrC-SiC ceramics along the thickness

Ablation resistance of SiC-modified nanocomposite ceramic coating prepared by LPDS method on titanium alloy

Preparation and ablation resistance of ZrC nanowires-reinforced CVD-ZrC coating on sharp leading edge C/C composites

Ablation behaviour of the CVD-(ZrC/SiC)3 alternate coating on C/C composites under oxyacetylene torch with different heat fluxes

Ablation behavior and mechanisms of ZrC-SiC-MoSi2 coated C/C-SiC-ZrC ceramic matrix composites under oxyacetylene torch

Study on the ablation performance of SiC-coated high thermal conductivity three-dimensional C/C composites

Microstructure and Ablation Performance of SiC–ZrC Coated C/C Composites Prepared by Reactive Melt Infiltration

Ablation behaviour of Csf/ZrB2-SiC composites fabricated by direct ink writing and reactive melt infiltration

Enhanced ablative resistance of C/C composites with densified ZrB 2 -based ceramics by incorporation of Mo as interface layer

Microstructure and Ablation Behavior of W/ZrC/SiC Coating on C/C Composites Prepared by Reactive Melt Infiltration and Atmospheric Plasma Spraying

Ablation of advanced C/C-ZrC-SiC leading edge composites

Phase and microstructure evolutions of in-situ ZrC composite coating under plasma torch ablation

Novel one-step formed composite reinforcement of "Spider web like" SiCnw networks and "Z-pins like" SiC rods for ablation resistance improvement of C/C-ZrC-SiC

UHTC coating reinforced by HfC nanowires against ablation for C/C composites

Ablation behavior of Cf/ZrC-SiC and Cf/SiC composites produced by precursor infiltration and pyrolysis combined with gaseous silicon infiltration

Effect of temperature-dependent nano SiC on the ablation resistance of ZrC coating