Abstract:Magnetorheological elastomers (MRE) are intelligent controllable materials used as polishing pads in chemical mechanical polishing (CMP), and the magnetic particles in the MRE polishing pad are used as solid-phase catalysts for heterogeneous Fenton reactions for oxidizing single-crystal SiC surfaces, thereby helping reduce the processing difficulty and obtain high-quality surfaces. The influence of the solid-phase catalyst (Fe3O4 mass fraction, particle size) and polishing solution environment (H2O2 concentration, pH value) on the CMP heterogeneous Fenton reaction polishing single-crystal SiC were investigated. The material removal behavior of the MRE polishing pad was investigated. The results demonstrated that the solid-phase catalyst, Fe3O4, has a better superior effect than the carbonyl iron powder (CIP). The polishing material removal rate (MRR) increased and the surface roughness (Ra) decreased with an increase in the Fe3O4 mass fraction. Superior polishing results were obtained at a particle size of 0.3 μm. The higher the H2O2 concentration in the polishing solution, the greater the MRR, with lower Ra at 10% concentration. The highest MRR and lowest Ra were achieved at pH = 3 in acidic environments. During polishing, the heterogeneous Fenton reaction can significantly enhance the removal ability of polishing materials. The MRR increased by 33.4% with the heterogeneous Fenton reaction compared with those without the heterogeneous Fenton reaction, and the contribution of the heterogeneous Fenton reaction to total material removal was 25.03%. The analysis of the SiC–Abrasive–MRE polishing pad contact state revealed that the heterogeneous Fenton reaction can oxidize the SiC surface and reduce the surface hardness, increasing the indentation depth δwa of the abrasive grain into the SiC surface and exhibiting greater material removal.

Study of catalytic properties and grinding performance of single-crystal SiC heterogeneous Fenton reaction grinding discs

Study on heterogeneous Fenton reaction parameters for polishing single-crystal SiC using magnetorheological elastomers polishing pads

Studies on the Surface Quality of the Unsteady-State Grinding Technique

Effect of Ultrasonic Vibration Assisted Grinding Process on Surface Topography and Properties of C/SiC Composite

Accelerated C-face polishing of silicon carbide by alkaline polishing slurries with Fe3O4 catalysts

Mechanism of chemical and mechanical mutual promotion in photocatalysis-assisted chemical mechanical polishing for single-crystal SiC

Chemical Mechanical Polishing for Monocrystal SiC Assisted by the Heterogeneous Sono-Fenton Oxidation

Mechanism analysis and process optimization of nanogrinding single-crystal SiC

Chemical mechanical polishing of silicon carbide (SiC) based on coupling effect of ultrasonic vibration and catalysis

Achieving Ultralow Surface Roughness and High Material Removal Rate in Fused Silica Via a Novel Acid SiO2 Slurry and Its Chemical-Mechanical Polishing Mechanism

Preparation and polishing properties of water-based magnetorheological chemical finishing fluid with high catalytic activity for single-crystal SiC

Investigation on Material Removal Mechanisms in Photocatalysis-Assisted Chemical Mechanical Polishing of 4H–SiC Wafers

Development of core–shell SiO 2 @A-TiO 2 abrasives and novel photocatalytic chemical machinal polishing for atomic surface of fused silica

Optimizing of Grinding Parameters and Research of Grinding Mechanism of Reaction-bond Silicon Carbon

Optimization of polishing fluid composition for single crystal silicon carbide by ultrasonic assisted chemical-mechanical polishing

Material removal characteristics of ultra-precision grinding silicon carbide ceramics

Photocatalysis-Assisted Chemical Mechanical Polishing of SiC Wafer Using a Novel SiO2@TiO2 Core-Shell Composite Nanoparticles Slurry

Chemical Mechanical Planarization (cmp) of On-Axis Si-Face Sic Wafer Using Catalyst Nanoparticles in Slurry

Investigation on Electrical Enhanced Photocatalysis Polishing of Single-Crystal Silicon Carbide Substrates

Application of surface analysis in study on removal mechanism and abrasive selection during fused silica chemical mechanical polishing

Novel green chemical mechanical polishing of fused silica through designing synergistic CeO 2 /h-BN abrasives with lubricity