Abstract:Solid oxide fuel cells (SOFCs) electrochemically convert hydrogen and oxygen into electricity, heat, and water with high efficiency (~55%) [1], while in reverse operation, water and electricity are converted to hydrogen and oxygen in solid oxide electrolysis cells (SOECs). Appropriately designed solid oxide cells (SOCs) can operate in both SOFC and SOEC mode. Conventional SOCs typically demand elevated operating temperatures (800-1000°C), resulting in higher cost and accelerated degradation issues. Lowering operating temperatures below 600°C reduces thermal stresses, shortens start-up times, and broadens applications [2]. Ce 1-x Gd x O 2-δ (GDC), due to its superior oxygen ion conductivity at reduced temperatures, has lower ohmic losses than competing electrolyte materials. Thus, our 1.2 cm diameter circular anode supported GDC cell with 0.31 cm 2 active area exhibits exceptional power densities, reaching approximately 3 watt per square centimeter at 650°C. Through optimal design, these cells exhibit exceptional performances in fuel cell mode, significantly enhancing efficiency and effectiveness when operating as an electrolyzer for fuel generation. This advance in performance is a result of mitigating the leakage current issues typical of ceria-based electrolytes through precise engineering of the cathodic microstructure and surface chemistry modification [3]. The transition from lab-scale to large-scale commercialization (with active areas of 16 cm2 &; 81 cm2) presents significant challenges such as tailoring material properties for large-cell versus button-cell synthesis while maintaining high performance levels. In this work we explore the challenges encountered during the scaling-up process. We report on fabrication strategies employed to achieve cell flatness, maintain high efficiency, ensure cost-effectiveness, and achieve long-term stability. Specifically, we have fabricated graded anode-supported cells [4] by developing an innovative lamination strategy involving tapes oriented perpendicular to each other. This approach notably contributed to achieving superior electrolyte densification and resulted in significantly flatter (low curvature values) with respect to both horizontal and vertical axes in cartesian coordinate space. When compared to the flatness values of 10x10 cm 2 commercially available cells, our cells demonstrated remarkably flatter curvatures as shown in figure 1. This characteristic has proven highly beneficial for stack assembly, minimizing issues such as cell cracking and reducing sealing-related problems. By optimizing the cathode scaffold and infiltration process on larger area cells through a spray-coating machine, scaling up challenges are effectively mitigated compared to the button cell approach, where scaffold preparation and infiltration were performed using blade coating and a hand pipette, respectively. This approach effectively tackles electronic conduction issues in ceria-based electrolytes, leading to higher Open Circuit Voltages (OCVs) in fuel cell mode and increased efficiencies in reversible mode. References: D. Wachsman, and K. T. Lee, Science, 334 , 935 (2011). Q. Minh, Journal of the American Ceramics Society , 76 , 563 (1993). A. Robinson, Y. L. Huang, S. A. Horlick, J. Obenland, N. Robinson, J. E. Gritton, A. M. Hussain, E. D. Wachsman, Advanced Functional Materials , (In press). Ostrovskiy, M. Saqib, J. Hong and E. D. Wachsman, The Electrochemical Society , MA2023-01 , 132 (2023). Figure 1

Achieving Direct Electrochemical Oxidation of Carbon below 600oC through a Novel Direct Carbon Fuel Cell

A high performance intermediate temperature fuel cell based on a thick oxide–carbonate electrolyte

Optimization of a Direct Carbon Fuel Cell for Operation below 700 °C

A Promising Direct Carbon Fuel Cell Based on the Cathode-Supported Tubular Solid Oxide Fuel Cell Technology

On the Catalytic Activity of Ceria for Direct Carbon Conversion in a SOFC

Research Development on Novel Anode of Solid Oxide Direct Carbon Fuel Cells

Mechanism for carbon direct electrochemical reactions in a solid oxide electrolyte direct carbon fuel cell

Simulation-guided design of a finger-like nickel-based anode for enhanced performance of direct carbon solid oxide fuel cells

Direct-Methane Solid Oxide Fuel Cells with Hierarchically Porous Ni-Based Anode Deposited with Nanocatalyst Layer

Al-MOF derived porous carbon modified Pt/C catalyst for constructing high-performance super fuel cell via ORR + EDLC parallel discharge mechanism

Low Temperature Solid Oxide Fuel Cells with Hierarchically Porous Cathode Nano-Network

Investigation of ceria-molten carbonate electrolyte, composite anode and its catalytical effect on various carbon fuels in molten carbonate direct coal/carbon fuel cell

Spherical mesoporous Fe–N–C catalyst for the air cathode of membrane-less direct formate fuel cells

Fabrication and Performance of Ceramic Anode-Supported Solid Oxide Fuel Cells

Performance improvement of direct carbon fuel cell by introducing catalytic gasification process

Enhance coking tolerance of high-performance direct carbon dioxide-methane solid oxide fuel cells with an additional internal reforming catalyst

Research and Development of Solid Oxide Direct Carbon Fuel Cell

Transitioning Low-Temperature GDC Socs: Lab to Commercialization Scale

High performance low temperature solid oxide fuel cells with novel electrode architecture

A Comparative Study of Different Carbon Fuels in an Electrolyte-Supported Hybrid Direct Carbon Fuel Cell

Samaria-Doped Ceria Electrolyte Supported Direct Carbon Fuel Cell with Molten Antimony As the Anode