Graph Partitions and Concept Lattices

J. Abello,Alex J. Pogel

DOI: https://doi.org/10.1090/dimacs/070/06

Abstract:

What problem does this paper attempt to address?

Influence of luting agents on fracture resistance of endodontically treated incisors with metal posts

Xinhua GU,Caiyun MAO,Xiaoxiang WANG

DOI: https://doi.org/10.3969/j.issn.1003-7632.2007.06.024

2007-01-01

Abstract:Objective This study was to evaluate whether resin luting system could improve the fracture resistance of endodontically treated incisors with prefabricated and cast metal posts.Methods Fourty intact maxillary central incisors after endodontical treatments were randomly assigned to four groups of 10 teeth each. The teeth were then restored with prefabricated titanium alloy posts or cast nickel-chromium post-and-cores and metal-ceramic crowns. The posts and crowns were cemented with either adhesive composite resin luting system or glass ionomer cement. All restored teeth were thermocycled for 5000 cycles (5℃/55℃) as a fatigue test. Each specimen was secured in a universal testing machine. A compressive load was applied at an angle of 135 degrees to the long-axis of the tooth with a crosshead speed of 1.5mm/s until initial fracture. Fracture loads and modes (repairable or catastrophic) were recorded.Results The fracture load was 499.82±168.90N in the group of Ti-alloy post with resin cement (group 1) and was 388.98±125.22N in the group of the same posts with glass ionomer cement (group 2); The fracture load in the group of cast post with resin cement (group 3) was 412.55±99.29N,while 337.41±121.18N in the group of the same posts with glass ionomer cement (group 4). The repairable fracture observed from Group 1 to Group 4 was 40%, 20%, 20% and 30% respectively. No significant difference was found for fracture load and fracture mode between groups with different luting agents (P>0.05).Conclusion It indicates that adhesive composite resin luting system might not significantly improve the fracture resistance of the pulpless incisors restored with metal posts.
A protocol for a comparative evaluation of the fracture resistance of endodontically treated teeth reinforced with Cention N, resin-modified glass ionomer cement (RMGIC) and short fiber reinforced flowable composite as an intraorifice barrier

Namrata Jidewar,Manoj Chandak

DOI: https://doi.org/10.12688/f1000research.133800.2

2024-07-26

Abstract:Background: Endodontic treatment is the most common method for resolving pulpal and periapical pathology. However, various studies have reported that almost 11%-13% of all teeth that undergo extraction after endodontic treatment show the presence of cracks, craze lines, and vertical root fractures. Teeth with inadequate post endodontic restoration are more prone to fracture and coronal leakage, resulting in the diffusion of oral fluids, bacteria, bacterial products, and possibly root canal treatment failure. Furthermore, studies have advocated the use of endodontically treated teeth with restorative materials that have a similar or higher elastic modulus than the tooth for providing stiffness against forces that cause root fracture. Intraorifice barriers made of restorative materials that can bond to radicular dentin could thus be used to reinforce the radicular dentin while also preventing coronal microleakage. Although the sealing ability of intraorifice barriers has been widely compared in the literature, there have been few studies on the strengthening effect of the materials used in the study as intraorifice barriers when placed into the root canal. As a result, the current in vitro study aims to assess the effect of various materials as intraorifice barriers (Cention N, Resin modified glass ionomer cement, and short fiber reinforced flowable composite) on the force required fracture teeth after root canal treatment. Methods: This in vitro study will be done on extracted human mandibular premolars with single root canal where after doing root canal treatment 2-3 mm obturating material would be replaced by intra orifice barriers (Cention N, resin modified glass ionomer cement [RMGIC], and short fiber reinforced flowable composite). The force required to fracture teeth will be calculated using universal testing machine.
Oxygen Transport in the Critically Ill Patient

M. Wendt,P. Lawin

DOI: https://doi.org/10.1007/978-3-642-75646-7

Abstract:
Effect of surface treatments on fracture resistance of root filled teeth with bonded fibre posts

Atiyeh Feiz,Pooran Samimi,Ali Karami,Hamid Badrian,Hossein Goroohi,Edward J Swift Jr

DOI: https://doi.org/10.1111/edt.12084

Abstract:Background/aim: This study examined the effect of several dentin surface treatments on fracture resistance of root filled teeth containing bonded fibre posts. Material and methods: The roots of 84 single-canal premolars were instrumented, filled with gutta-percha and randomly divided into seven groups. The coronal 9 mm of gutta-percha was removed to create a post space. In the experimental groups, canals were irrigated with distilled water, 37% phosphoric acid, 5% sodium hypochlorite, 17% EDTA, 5% sodium hypochlorite followed by 17% EDTA or 5% sodium hypochlorite followed by 10% ascorbic acid. Fibre posts were cemented using Panavia F2.0 resin cement, and the specimens were mounted in acrylic resin blocks. Following 1-week storage in an incubator, specimens were thermocycled and their fracture resistance was determined using a universal testing machine. Data were analysed using the Kruskal-Wallis test. Results: Mean fracture resistance values ranged from 465.8 N in specimens treated with sodium hypochlorite and ascorbic acid to 739.1 N for those treated with sodium hypochlorite only. However, differences in fracture resistance were not statistically significant (P = 0.114). Conclusions: None of the surface treatments improved vertical fracture resistance of root filled teeth containing bonded fibre posts.
Influence of Direct Coronal Restoration Materials on the Fracture Resistance of Endodontically Treated Premolars: An In Vitro Study

Georgiana Florentina Gheorghe,Ana Maria Cristina Țâncu,Oana Elena Amza,Ioana Suciu,Laura Iosif,Stanca Cuc,Ioan Petean,Marioara Moldovan,Bogdan Dimitriu

DOI: https://doi.org/10.3390/dj12090294

2024-09-19

Abstract:(1) Background: The long-term survival of an endodontically treated tooth depends on a successful root canal treatment as well as an adequate definitive coronal restoration. This study aimed to evaluate the strength of endodontically treated premolars with mesial-occlusal-distal (MOD) cavity preparation restored with different direct coronal restoration materials but from the same manufacturer against fracture. (2) Methods: sixty intact premolars were selected and placed into five groups (n = 12): G1-intact teeth, G2-endodontic treatment and unrestored MOD cavities, G3-endodontic treatment and MOD cavities restored with Tetric PowerFlow and Tetric EvoCeram, G4-endodontic treatment and MOD cavities restored with Multicore Flow and Tetric EvoCeram, and G5-endodontic treatment and MOD cavities restored with Multicore Flow. The specimens were subjected to an axial compression load at a speed of 1.6 mm/min and optically inspected before and after with a stereomicroscope. For each premolars group, the following data were recorded: the compression resistance, the compressive strength, and the maximum force supported. The microstructure of the samples after the compression test was analyzed using scanning electron microscopy (SEM). (3) Results: statistical analysis (ANOVA and Tukey test) showed that there was a statistically significant difference between G1 and the other groups. Even though there was no statistically significant difference between the restored groups, a better mechanical behavior was registered within the G3. (4) Conclusions: this in vitro study indicated that none of the materials used can lead to a higher or at least similar fracture resistance as the intact teeth. The coronal restoration only with nano-hybrid composites may lead to a higher therapeutic benefit for the fracture-susceptible premolars.
The effect of sealer type and obturation technique on the fracture resistance of endodontically treated roots

Ahmad S Al-Hiyasat,Anas M Sawallha,Nessrin A Taha

DOI: https://doi.org/10.1007/s00784-023-05326-2

Abstract:Objective: This study evaluated the effect of sealer type with various obturation techniques on the fracture resistance of root filled teeth. Materials and methods: Eighty mandibular premolars were collected, and root canals of 70 of them were prepared by Mtwo system up to 40/04. Thirty teeth were obturated using TotalFill BC sealer, and 30 using AH Plus sealer, with one of the obturation techniques (N = 10), namely cold lateral compaction (CLC), warm vertical compaction (WVC), and single cone (SC). Ten teeth were left without obturation as a positive control, and the other 10 teeth were not prepared serving as a negative control. Teeth were stored for 3 weeks, and the crowns were separated and the roots were subjected to fracture test using a universal testing machine. Results: Data was analyzed by ANOVA followed by Tukey's test. Fracture resistance of the TotalFill groups was significantly higher than the AH Plus groups in each obturation technique, and SC had the highest fracture resistance regardless of sealer used (P < 0.05). Obturation of the root canal by TotaFill BC sealer increased the calcium/phosphorous ratio in the dentin of the root. Conclusions: Obturation with TotalFill BC sealer improved the fracture resistance of the roots more than AH Plus sealer, and obturation with SC resulted in higher fracture resistance than CLC and WVC. Clinical relevance: Obturation of the root canal with Bioceramic sealer with single cone obturation technique could reduce the incidence of vertical root fracture.
Impact of Access Cavity Design on Fracture Resistance of Endodontically Treated Maxillary First Premolar: In Vitro

Anju Daniel,Abdul Rahman Saleh,Anas Al-Jadaa,Waad Kheder

DOI: https://doi.org/10.1590/0103-6440202405676

2024-03-22

Abstract:This study was designed to investigate the impact of access cavity designs on fracture resistance of endodontically treated maxillary first premolars. The study sample consisted of 72 intact maxillary first premolars, randomly divided into six groups (n = 12). A standardized proximal cavity preparation was prepared for all samples using standard bur. Groups I: control group with only standard proximal cavity and no endodontic access, group II: Truss access cavity, group III: Separated access to buccal and palatal canals without removal of dentine in between, group IV: Access to buccal and palatal canals with removal of dentine in between, group V: Traditional access cavity, group VI: Mesio-occlusal-distal cavity (MOD). For groups I and VI, only composite restoration was used to restore the proximal cavity, while for groups II- V, the access was prepared and endodontic treatment was performed on all teeth, then composite restoration was placed. The root canals were instrumented using nickel-titanium files, irrigated with sodium hypochlorite, and filled with AH plus sealer and gutta-percha using warm vertical condensation. All samples were then placed in an acrylic mold and underwent thermal aging for 10,000 cycles between 5 and 55°C. The samples were fixed in a universal testing machine with the long axis of the roots positioned at 20° to a load applied at a crosshead speed of 1 mm/min using a stainless steel semi-spherical indenter (Ø = 3 mm) until fracture occurred to determine the fracture resistance force in Newton. The normality test (Shapiro-Wilk) showed that data are normally distributed. Group II exhibited the highest mean fracture resistance, and group VI was the least likely to resist the fracture. No statistically significant differences between tested groups (p-value = 0.237). The MOD group showed a more unfavorable mode of fracture compared to other groups. No significant difference in fracture resistance between conservative and traditional access cavities. The missing marginal ridges, such as in MOD cavities played an important role in decreasing the fracture resistance of endodontically treated teeth.
Fracture Resistance of Endodontically Treated Maxillary Premolar Teeth Restored with Wallpapering Technique: A Comparative In Vitro Study

Shahed Wissam Abdulamir,Manhal A. Majeed

DOI: https://doi.org/10.1155/2023/6159338

2023-04-27

International Journal of Dentistry

Abstract:Objectives. This in vitro study aimed to evaluate and compare the fracture resistance and mode of failure of endodontically treated maxillary premolar teeth restored with different direct composite restorative techniques. Materials and Methods. Forty freshly extracted maxillary premolar teeth with comparable sizes were used in this in vitro study. Each tooth received mesio-occluso-distal cavity preparation (3 mm width and 6 mm depth) followed by endodontic treatment. Canals were instrumented with RACE EVO rotary files (FKG, Dentaire, Switzerland) up to MAF 25/.06. Canals were obturated using a single cone technique, then the teeth were divided arbitrarily into five groups (n = 8): Group A: direct composite resin only using a centripetal technique, Group B: direct composite resin with glass fiber post, Group C: direct composite resin with short fiber-reinforced composite (everX Flow), Group D: direct composite resin with leno wave ultra high molecular weight polyethylene (LWUHMWPE) fibers placed on cavity floor, and Group E: direct composite resin with LWUHMWPE fibers placed circumferentially around the cavity walls (wallpapering technique). The teeth were then stored in distilled water at 37°C for 24 hr. The fracture resistance of each sample was measured using a universal testing machine in Newton (N). The data were analyzed using one-way analysis of variance (ANOVA) and the Bonferroni test with a significance level of 0.05. Results. Group E recorded the maximum mean of fracture load (2,139.375 N), while Group A recorded the minimum mean of fracture load (689.6250 N). The one-way ANOVA test revealed a significant difference between the groups. The Bonferroni test showed a significant difference between each two groups, with the exception of those between Groups B and C and between Groups D and E, where there were no statistically significant differences ( p > 0.05 ). Conclusion. Restoration of endodontically treated teeth using the wallpapering technique recorded the highest mean of fracture resistance with a repairable mode of fracture.
Importing human pluripotent stem cell lines derived at another institution: tailoring review to ethical concerns.

B. Lo,Lindsay Parham,Christopher Broom,M. Cedars,E. Gates,L. Giudice,D. G. Halme,William Hershon,A. Kriegstein,P. Kwok,M. Oberman,Clifford Roberts,Richard M. Wagner

DOI: https://doi.org/10.1016/j.stem.2009.01.013

IF: 23.9

2009-02-06

Cell Stem Cell

Abstract:
Fracture resistance and marginal gap formation of post-core restorations: influence of different fiber-reinforced composites

Márk Fráter,Lippo Lassila,Gábor Braunitzer,Pekka K Vallittu,Sufyan Garoushi

DOI: https://doi.org/10.1007/s00784-019-02902-3

Abstract:Objectives: The aim was to explore the fracture behavior and marginal gap within the root canal of endodontically treated (ET) premolars restored with different fiber-reinforced post-core composites (FRCs). Further aim was to evaluate the composite curing at different depths in the canal. Materials and methods: Eighty-seven intact upper premolars were collected and randomly divided into six groups. After endodontic procedure, standard MOD cavities were prepared and restored with their respective fiber-reinforced post-core materials: group 1: prefabricated unidirectional FRC-post + conventional composite core; group 2: prefabricated unidirectional FRC-post + short fiber composite (SFRC) core; group 3: individually formed unidirectional FRC-post + conventional composite core; group 4: randomly oriented SFRC directly layered as post and core; group 5: individually formed unidirectional FRC + randomly oriented SFRC as post and core. After restorations were completed, teeth (n = 3/group) were sectioned and then stained. Specimens were viewed under a stereo microscope and the percentage of microgaps within the root canal was calculated. Fracture load was measured using universal testing machine. Results: SFRC application in the root canal (groups 4 and 5) showed significantly higher fracture load (876.7 N) compared to the other tested groups (512-613 N) (p < 0.05). Post/core restorations made from prefabricated FRC-post (group 1) exhibited the highest number of microgaps (35.1%) at the examined interphase in the root canal. Conclusions: The restoration of ET premolars with the use of SFRC as post-core material displayed promising performance in matter of microgap and load-bearing capacity. Clinical significance: Fracture resistance of ET premolar restored by bilayered composite restoration that includes both SFRC as post-core material and surface conventional resin seems to be beneficial.
Comparative Evaluation of Fracture Resistance of Composite Core Buildup Materials: An In Vitro Study

Deepmala Pande,Niharika Benjamin,Vishakha Rani,Malik Hina,Shreya Haldar,Harni Nirmal,Shivani Gole,Md Sadique Ali

DOI: https://doi.org/10.7759/cureus.63298

2024-06-27

Cureus

Abstract:Aim This study aimed to compare the fracture resistance of different materials used in composite core buildups, including conventional filler composite, nanofiller composite, and short fiber-reinforced composite (SFRC). Methods This in vitro study was conducted on 30 freshly extracted premolars. The teeth were treated using a uniform endodontic procedure, and Fiber Posts (REFORPOST, Angelus) were placed. The teeth were then divided into three groups and restored using different materials. Group 1 was restored using SFRC (everX Posterior, GC, Europe), Group 2 using microfiller composite (Te-Econom Flow, Ivoclar Vivadent), and Group 3 using nanofiller composite (Tetric N-Flow, Ivoclar Vivadent). The restoration materials were then light-cured for 40 seconds. The teeth were placed in a Universal Testing Machine (Instron) and a load was applied with a stainless-steel ball (4 mm diameter) until the tooth fractured. The fracture load for each tooth was recorded, and after the mechanical test, the experimental groups were examined for failure modes. Statistical analysis was performed using SPSS version 21.0 software. A one-way ANOVA test was conducted to compare more than two groups, followed by Tukey's test for post hoc pairwise comparison. Results The mean fracture resistance of the microfiller composite (346.94±44.63) was the lowest among the three groups. When analyzed using Tukey's test at p<0.05, fracture resistance was significantly higher in the SFRC, followed by nanofillers and microfiller composites. Conclusion Due to the increasing demand for aesthetic restorations in recent years, composites have become important in modern restorative dentistry. The development and implementation of composite dental restorative materials rely on a comprehensive understanding of each composite component and consideration of methods for modifying each component. As a result, the findings of this study will be beneficial in determining which material to use based on specific cases.
Studies on the electrophoretic mobility of the Wassermann reagins in different stages of syphilis.

A. Laurell,A. Lindau

DOI: https://doi.org/10.1111/J.1699-0463.1958.TB01730.X

2009-08-18

Abstract:
To Compare and Evaluate the Fracture Resistance of Three Post Endodontic Restorations Including Silver Amalgam, Dual Cure Composite Resin and Fibre Reinforced Composite Resin

Kalpana Pawar Patil,Shivani Vyavahare,Sadashiv Daokar,Komal Potfode,Kshama Sarak,Madhuri Khatod

DOI: https://doi.org/10.38124/ijisrt/ijisrt24jan1513

2024-04-05

Abstract:Background: Endodontically treated teeth are thought to be more prone to fracture. The last stage in a successful root canal treatment is to restore root canal-treated teeth with a permanent, definitive postendodontic restoration. Dehydration, dentin loss during endodontic procedures, and the elimination of significant anatomic elements like cusps, ridges, and the pulp chamber's arched roof—all of which contribute significantly to the normal tooth's support—are the causes of the fracture of endodontically treated teeth. Consequently, intracoronal strengthening is necessary to prevent tooth fracture, especially in the posterior teeth where compressive stresses brought on by occlusal forces can cause tooth fractures.1 Since core materials typically replace a significant portion of the tooth structure and must withstand multidirectional masticatory forces,their compressive strength is crucial.2  Aim: The purpose of this study was to compare the compressive strengths of three direct post enododontic restorations.  Material and Methods: There are thirty extracted maxillary premolars chosen. After receiving root canal therapy, the teeth were divided randomly into three groups for immediate post-endodontic restorations: (i) silver amalgam (ii)Fiber-reinforced composite resin (iii) dual cure glass- reinforced composite resin . After that, a Universal Testing Machine was used to apply compressive stress on the teeth.  Statistical Analysis: Fracture loads will be compared statistically, and the data will be analysed using version 21.0 of SPSS software, analysis of variance and the Post-hoc test for multiple comparisons.  Result and Conclusion: Within the limits of the study, it showed that the post hoc tests reveal that the mean difference of compressive load strength is significant between all the groups, Amalgam has highest load strength followed by Fiber reinforced composite. Dual cure composite has lowest compressive load strength.
Effect of Long Glass Fiber Orientations or a Short-Fiber-Reinforced Composite on the Fracture Resistance of Endodontically Treated Premolars

Ecehan Hazar,Ahmet Hazar

DOI: https://doi.org/10.3390/polym16091289

IF: 5

2024-05-04

Polymers

Abstract:This study aimed to evaluate the effect of direct restorations using unidirectional glass fiber orientations and a short-fiber-reinforced composite (SFRC) on the fracture resistance of endodontically treated premolars with mesio-occluso-distal cavities. Ninety double-rooted premolars were selected. Fifteen teeth were left intact/as a control group. The endodontic treatment and cavity preparations of seventy-five teeth were performed and divided into five experimental groups: Resin composite (RC), modified transfixed technique + RC, circumferential technique + RC, cavity floor technique + RC, and SFRC + RC. All teeth were fractured under oblique static loading at a 30° angle using a universal testing machine. The fracture patterns were observed and classified. Data were analyzed with one-way analysis of variance, Pearson chi-square, and Tukey HSD post hoc tests (p = 0.05). The highest fracture strength values were obtained in intact teeth (599.336 N), followed by modified transfixed + RC treated teeth (496.58 N), SFRC + RC treated teeth (469.62 N), RC (443.51 N), circumferential + RC treated teeth (442.835 N), and cavity floor + RC treated teeth (404.623 N) (p 0.05). Unrepairable fractures were observed at low rates (20%) in the modified transfixed + RC and SFRC + RC teeth, and at higher rates in RC (73.3%), cavity floor + RC (60%), and circumferential + RC (80%) teeth. The application of an SFRC or the modified transfixed technique yielded an improved fracture strength and the fracture pattern of ETPs being restored with a universal injectable composite.

polymer science
[Acute edema of the lung, non-cardiogenic, after re-expansion].

F. Jatene,M. Bechara,C. R. Carvalho,M. Jatene,B. Tranchesi,J. Ramires,G. Verginelli,A. Jatene

1986-11-01

Abstract:
Finite element and in vitro study on biomechanical behavior of endodontically treated premolars restored with direct or indirect composite restorations

Tatjana Maravić,Allegra Comba,Claudia Mazzitelli,Luca Bartoletti,Irene Balla,Elisabetta di Pietro,Uroš Josić,Luigi Generali,Darko Vasiljević,Larisa Blažić,Lorenzo Breschi,Annalisa Mazzoni

DOI: https://doi.org/10.1038/s41598-022-16480-0

IF: 4.6

2022-07-26

Scientific Reports

Abstract:Objectives of the study were to investigate biomechanical properties of severely compromised premolars restored with composite restorations using finite element analysis (FEA), and in vitro fracture resistance test. A 3-D model of an endodontically treated premolar was created in Solidworks. Different composite restorations were modelled (direct restoration-DR; endo-crown-EC; post, core, and crown-C) with two different supporting tissues: periodontal ligament/alveolar bone (B), and polymethyl methacrylate (PMMA). Models were two-point axially loaded occlusally (850 N). Von Mises stresses and strains were calculated. The same groups were further tested for static fracture resistance in vitro (n = 5, 6.0 mm-diameter ball indenter, vertical load). Fracture resistance data were statistically analyzed ( p < 0.050). The highest stresses and strains in all FEA models were observed on occlusal and vestibular cervical surfaces, corresponding to fracture propagation demonstrated in vitro. C showed the lowest stress in dentin, while EC showed lower stresses and strains in crown cement. B models demonstrated larger high stress areas in the root than PMMA models. No significant differences in fracture resistance (N) were observed between groups (DR: 747.7 ± 164.0, EC: 867.3 ± 108.1, C: 866.9 ± 126.3; p = 0.307). More conservative restorations seem a feasible alternative for endodontically treated premolars to conventional post-core-crown.

multidisciplinary sciences
Fracture resistance and failure pattern of endodontically treated maxillary premolars restored with transfixed glass fiber post: an in vitro and finite element analysis

Saleem Abdulrab,Greta Geerts,Ganesh Thiagarajan

DOI: https://doi.org/10.1080/10255842.2023.2252954

2023-09-02

Abstract:The aims of the study were to determine the effect of different types of endodontic sealers and the presence of a horizontal glass fiber post (HGFP) on the fracture resistance and fracture pattern of mesio-occluso-distal (MOD) restored upper premolars and to analyze the stress distribution. Sixty extracted upper premolars received root canal treatment (RCT) and a MOD cavity preparation. All MOD cavities were restored with the same composite resin (CR). The 60 teeth were divided randomly into 6 groups ( n = 10); Group1= AH Plus sealer; Group 2= TotalFill BC sealer; Group 3= BioRoot RCS sealer; Group 4= AH plus sealer + HGFP; Group 5= TotalFill BC sealer + HGFP; and, Group 6= Bio Root RCS sealer + HGFP. All specimens were thermocycled and subjected to cyclic loading. Next, the specimens were subjected to a static load using a universal testing machine. Data were analyzed using two-way ANOVA. Two micro-CTs of the same upper premolar, one without the HGFP and later one with HGFP inserted were made and used to create two finite element (FE) models. For the fracture resistance, two-way ANOVA revealed significant differences for the effect of HGFP ( p = 0.029), but no differences for the effect of root canal sealer type ( p = 0.561). The HGFP groups showed higher restorable fracture compared to groups without HGFP ( p = 0.013). Finite element analysis showed that the inclusion of HGFP reduces stress concentration at the occlusal interface and cervical region. Therefore, it can be concluded that HGFP significantly increased the fracture resistance of endodontically treated upper premolars with MOD cavities and reduced the risk for non-restorable fractures. The FE analysis supports the mechanical test results.

engineering, biomedical,computer science, interdisciplinary applications
Recent natural products based drug development: a pharmaceutical industry perspective.

Yue-Zhong Shu

DOI: https://doi.org/10.1021/NP9800102

IF: 5.1

1998-07-11

Journal of Natural Products

Abstract:This article reviews the natural products based drug development in the past 10-15 years in these aeras: infectious disease, neurological disease, cardiovascular and metabolic disease, oncological disease, and immunological, inflammatory and related diseases
Influence of Intracanal Irrigants on Coronal Fracture Resistance of Endodontically Treated and Bleached Teeth: An In vitro Study

Maryam Khoroushi,Fatemeh Tavakol,Farinaz Shirban,Sanaz Ziaei

DOI: https://doi.org/10.4103/ccd.ccd_445_17

Abstract:Background: Irrigation has a key role in the success of endodontic treatment. Intracanal irrigant solutions have adverse effects on the physical properties of dentin. Aim: The present study aimed to evaluate the effect of different irrigation protocols on coronal fracture resistance of endodontically treated teeth undergoing bleaching treatment. Design and materials and methods: Access cavities were prepared in 120 maxillary premolars which were divided into two groups (n = 60) - Group A: nonbleached, Group B: bleached (B). Each group was subdivided into five subgroups based on irrigation protocol (n = 12); G1: normal saline (NS), G2: 2.5% sodium hypochlorite (NaOCl), G3: 10% citric acid (CA), G4: 17% ethylene diamine tetra acetic acid, and G5: NaOCl plus CA. In Group B, the teeth were bleached using 38% hydrogen peroxide and 20% carbamide peroxide gels as in-office and at-home bleaching techniques for 3 weeks. All the teeth were restored with composite resin, thermocycled, and incubated for 24 h. The specimens underwent fracture resistance tests. Data were analyzed with ANOVA, Tukey honestly significant difference test, t-test, and Chi-squared test (α =0.05). Results: T-test showed significant differences between each two corresponding subgroups (P < 0.0001). In Group A, NS demonstrated significantly higher fracture resistance compared to others; however, minimum fracture resistance recorded in G2. In Group B, the maximum fracture resistance was recorded in G1, with the minimum being recorded in G5. Samples irrigated with NaOCl and NaOCl plus CA exhibited significantly lower fracture resistance compared to NS subgroup (P < 0.05). Conclusions: Within the limitations of this study, it can be concluded that the irrigation protocol used during endodontic treatment with/without bleaching can affect the coronal fracture resistance.
Fracture Resistance of Endodontically Treated Teeth Restored Using Multifiber Posts Compared with Single Fiber Posts

Alhanoof Aldegheishem,Reem Barakat,Nour A. L. Huda Alrefaei,Ghaida Alhussain,Kolood Alkoblan,Ebtisam M. Al-Madi

DOI: https://doi.org/10.1155/2024/3203383

2024-05-13

International Journal of Polymer Science

Abstract:Purpose. The aim of this in vitro study was to evaluate the fracture resistance and type of failure of two adhesive fiber post systems used to restore endodontically treated teeth. Material and Methods. Twenty-seven extracted premolars were selected and divided into three groups ( n=9 ): a control group restored with direct composite core (group 1), teeth restored with single fiberglass posts (group 2), and teeth were restored with multifiber posts (Biolight Plus System) (group 3). Fracture resistance was measured by applying axial compressive loads parallel to the longitudinal axis of the tooth until failure. Data was analyzed with one-way ANOVA followed by post hoc Turkey tests. Results. The results showed that the mean forces to failure of the control group (0.068 kN) were significantly lower than those restored with either fiberglass post systems ( p=0.013 ). There was no significant difference between the multifiber and the single fiberglass post system in terms of resistance to fracture ( p=0.097 ). Although there are more teeth fractured favorably (above the CEJ) in the Biolight Plus group (77.7%) compared to both the control and fiberglass post groups, it was not statistically significant ( p=0.226 ). Conclusion. Within the limitations of this study, restoring endodontically treated with a multifiber post system is an adequate alternative to single fiberglass post system in terms of resistance to fracture.

polymer science

Graph Partitions and Concept Lattices

Influence of luting agents on fracture resistance of endodontically treated incisors with metal posts

A protocol for a comparative evaluation of the fracture resistance of endodontically treated teeth reinforced with Cention N, resin-modified glass ionomer cement (RMGIC) and short fiber reinforced flowable composite as an intraorifice barrier

Oxygen Transport in the Critically Ill Patient

Effect of surface treatments on fracture resistance of root filled teeth with bonded fibre posts

Influence of Direct Coronal Restoration Materials on the Fracture Resistance of Endodontically Treated Premolars: An In Vitro Study

The effect of sealer type and obturation technique on the fracture resistance of endodontically treated roots

Impact of Access Cavity Design on Fracture Resistance of Endodontically Treated Maxillary First Premolar: In Vitro

Fracture Resistance of Endodontically Treated Maxillary Premolar Teeth Restored with Wallpapering Technique: A Comparative In Vitro Study

Importing human pluripotent stem cell lines derived at another institution: tailoring review to ethical concerns.

Fracture resistance and marginal gap formation of post-core restorations: influence of different fiber-reinforced composites

Comparative Evaluation of Fracture Resistance of Composite Core Buildup Materials: An In Vitro Study

Studies on the electrophoretic mobility of the Wassermann reagins in different stages of syphilis.

To Compare and Evaluate the Fracture Resistance of Three Post Endodontic Restorations Including Silver Amalgam, Dual Cure Composite Resin and Fibre Reinforced Composite Resin

Effect of Long Glass Fiber Orientations or a Short-Fiber-Reinforced Composite on the Fracture Resistance of Endodontically Treated Premolars

[Acute edema of the lung, non-cardiogenic, after re-expansion].

Finite element and in vitro study on biomechanical behavior of endodontically treated premolars restored with direct or indirect composite restorations

Fracture resistance and failure pattern of endodontically treated maxillary premolars restored with transfixed glass fiber post: an in vitro and finite element analysis

Recent natural products based drug development: a pharmaceutical industry perspective.

Influence of Intracanal Irrigants on Coronal Fracture Resistance of Endodontically Treated and Bleached Teeth: An In vitro Study

Fracture Resistance of Endodontically Treated Teeth Restored Using Multifiber Posts Compared with Single Fiber Posts