Abstract:Ultra-high nickel single-crystal cathode materials have become the most promising for lithium-ion batteries. However, the preparation of ultra-high nickel single-crystal precursors by a continuous coprecipitation method has the disadvantages of large particle size, wide distribution, poor morphology. The extent of the inhomogeneous reactions can be more severe in single-crystal cathodes with larger particle size. Herein, the coprecipitation method with a solid concentrator was adopted, and citrate sodium was used as a complexing agent to improve the physical properties of precursors and electrochemical performance of single-crystal cathode materials. By analyzing the morphology and agglomeration mechanism of the precursor nucleuses under different pH values, it was found that hexagonal nanosheets grew along the 101 direction, and the primary particles showed thicker at pH of 11.4. The hexagonal nanosheets grew along the 001 direction, and the primary particles showed finer at pH of 12.2. The morphology and particle size uniformity of the secondary particles formed by agglomeration at these two pH values showed poor. However, hexagonal nanosheets grew synergistically along the 001 and 101 directions at pH of 11.8, so the primary particles with uniform particle size gradually agglomerated, and then the secondary particles with ultra-small particle size and uniform distribution obtained. Compared to materials prepared by the traditional continuous coprecipitation method, the precursor displays a smaller particle size(D50 = 1.8 µm), higher sphericity, uniformity and denser internal structure. In order to evaluate the performance of Ni0.94Co0.04Mn0.02(OH)2 with ultra-small particle size, the sintering conditions of LiNi0.94Co0.04Mn0.02O2 need to be explored. It was found that the LiNi0.94Co0.04Mn0.02O2 cathode material prepared at 790 °C exhibited higher discharge capacity, cycle and rate performance, compared to materials prepared at 760 °C and 820 °C. We further utilized TEM, EPMA, and XPS to test the internal structure and valence state of LiNi0.94Co0.04Mn0.02O2 cathode material. The results show that the LiNi0.94Co0.04Mn0.02O2 calcined at 790 °C has a good single crystal structure. The LiNi0.94Co0.04Mn0.02O2 cathode materials inherited the structure and particle size of Ni0.94Co0.04Mn0.02(OH)2 precursors, and displayed discharge capacity of 194.7 mAh/g and capacity retention rate of 89.8 % after 100 cycles at 1 C. The microstructure and phase transition of the as-prepared cathode material are well-maintained after long-term cycling, without obvious inter-crystalline micro-crack. The results indicate that its electrochemical performance is better than that of cathode materials with precursors prepared by a continuous coprecipitation method. This work provides new insights for the preparation of small-particle-size precursor and single-crystal cathode materials.

Effects of Coprecipitation Conditions on the Electrochemical Properties of Cobalt-Free LiNi0.9Mn0.1-xAlxO2 Cathodes

Enhanced Electrochemical Performance of LiNi0.8Co0.15Al0.05O2 Cathode Material via Li2TiO3 Nanoparticles Coating

Synthesis of LiNiO2 cathode materials with homogeneous Al doping at the atomic level

(Invited) Delineating the Intricacies Involved in the Synthesis of Cobalt-Free High-Nickel Layered Oxide Cathodes for Lithium-Ion Batteries

Effects of Al doping on the electrochemical performances of LiNi0.83Co0.12Mn0.05O2 prepared by coprecipitation

Al Substitution for Mn during Co-Precipitation Boosts the Electrochemical Performance of LiNi 0.8 Mn 0.1 Co 0.1 O 2

Influence of Al doping on the structure and electrochemical performance of the Co-free LiNi 0.8 Mn 0.2 O 2 cathode material

Enhanced Electrochemical Performance of LiNi0.8Co0.1Mn0.1O2 Cathode Materials Obtained by Atomization Co-Precipitation Method

Application of Nano Al2O3 Particles As Precipitate Nucleus for Preparation of High Rate Nickel-Rich Cathode Materials

An In-Depth Understanding of the Effect of Aluminum Doping in High-Nickel Cathodes for Lithium-Ion Batteries

Enhanced Electrochemical Performance of LiNi0.6Co0.2Mn0.2O2 Cathode Materials by Ultrasonic-Assisted Co-Precipitation Method

Insights on the Activation and Stabilization of NCA Cathode Interface: Surface Chemical State Modulations of Aluminum-Mediated Li 0.73 CoO 2 Coatings

Improving the Electrochemical Performance of Ni-rich Cathode Material LiNi 0.815 Co 0.15 Al 0.035 O 2 by Removing the Lithium Residues and Forming Li 3 PO 4 Coating Layer

Efficacy of atomic layer deposition of Al2O3 on composite LiNi0.8Mn0.1Co0.1O2 electrode for Li-ion batteries

One-Step Synthesis of Stoichiometric LiNi 0.80 Co 0.15 Al 0.05 O 2 Precursor in Acidic Environment and Its Facile Growth into Single Crystals at Low Temperatures for Li-Ion Batteries

Investigation of Li 3 PO 4 Coating and Nb 5+ Doping Effect on the Crystal Structure and Electrochemical Properties of Ni-Rich LiNi 0.85 Co 0.05 Mn 0.10 O 2 Cathode

Application of precursor with ultra-small particle size and uniform particle distribution for ultra-high nickel single-crystal cathode materials by coprecipitation method

Optimized structure stability and cycling performance of LiNi0.8Co0.1Mn0.1O2 through homogeneous nano-thickness Al2O3 coating

In Situ Monitoring of the Growth of Nickel, Manganese, and Cobalt Hydroxide Precursors during Co-Precipitation Synthesis of Li-Ion Cathode Materials

Effects of Al and Co doping on the structural stability and high temperature cycling performance of LiNi0.5Mn1.5O4 spinel cathode materials

Understanding the Feasibility of Manganese Substitution for Cobalt in the Synthesis of Nickel-Rich and Cobalt-Free Cathode Materials