Abstract:Atomic layer deposition (ALD) derived ultrathin conformal Al2O3 coating has been identified as an effective strategy for enhancing the electrochemical performance of Ni-rich LiNixCoyMnzO2 (NCM; 0 ≤x, y, z < 1) based cathode active materials (CAM) in Li-ion batteries. However, there is still a need to better understand the beneficial effect of ALD derived surface coatings on the performance of NCM based composite cathodes. In this work, we applied and optimized a low-temperature ALD derived Al2O3 coating on a series of Ni-rich NCM-based (NCM622, NCM71.51.5 and NCM811) ready-to-use composite cathodes and investigated the effect of coating on the surface conductivity of the electrode as well as its electrochemical performance. A highly uniform and conformal coating was successfully achieved on all three different cathode compositions under the same ALD deposition conditions. All the coated cathodes were found to exhibit an improved electrochemical performance during long-term cycling under moderate cycling conditions. The improvement in the electrochemical performance after Al2O3 coating is attributed to the suppression of parasitic side reactions between the electrode and the electrolyte during cycling. Furthermore, conductive atomic force microscopy (C-AFM) was performed on the electrode surface as a non-destructive technique to determine the difference in surface morphology and conductivity between uncoated and coated electrodes before and after cycling. C-AFM measurements on pristine cathodes before cycling allow clear separation between the conductive carbon additives and the embedded NCM secondary particles, which show an electrically insulating behavior. More importantly, the measurements reveal that the ALD-derived Al2O3 coating with an optimized thickness is thin enough to retain the original conduction properties of the coated electrodes, while thicker coating layers are insulating resulting in a worse cycling performance. After cycling, the surface conductivity of the coated electrodes is maintained, while in the case of uncoated electrodes the surface conductivity is completely suppressed confirming the formation of an insulating cathode electrolyte interface due to the parasitic side reactions. The results not only show the possibilities of C-AFM as a non-destructive evaluation of the surface properties, but also reveal that an optimized coating, which preserves the conductive properties of the electrode surface, is a crucial factor for stabilising the long-term battery performance.

Efficacy of atomic layer deposition of Al2O3 on composite LiNi0.8Mn0.1Co0.1O2 electrode for Li-ion batteries

Enhanced Electrochemical Performance of LiNi0.8Co0.15Al0.05O2 Cathode Material via Li2TiO3 Nanoparticles Coating

Advancing Lithium-Ion Batteries' Electrochemical Performance: Ultrathin Alumina Coating on Li(Ni0.8Co0.1Mn0.1)O2 Cathode Materials

Atomic Layer Deposition of Al2O3 on LiNi0.68Co0.10Mn0.22O2 for Enhanced Electrochemical Performance

Structural and Electrochemical Study of Al2O3 and TiO2 Coated Li1.2Ni0.13Mn0.54Co0.13O2 Cathode Material Using ALD

Optimized atomic layer deposition of homogeneous, conductive Al2O3 coatings for high-nickel NCM containing ready-to-use electrodes

Identification of the dual roles of Al2O3 coatings on NMC811-cathodes via theory and experiment

Atomic Layer Deposition of Al2O3-Ga2O3 Alloy Coatings for Li[Ni0.5Mn0.3Co0.2]O2 Cathode to Improve Rate Performance in Li-Ion Battery.

Optimized structure stability and cycling performance of LiNi0.8Co0.1Mn0.1O2 through homogeneous nano-thickness Al2O3 coating

High-performance LiNi0.8Mn0.1Co0.1O2 cathode by nanoscale lithium sulfide coating via atomic layer deposition

Atomic layer deposition of solid-state electrolyte coated cathode materials with superior high-voltage cycling behavior for lithium ion battery application

Enhancing the High-Voltage Cycling Performance of LiNi<u>0.5</u>Mn<u>0.3</u>Co<u>0.2</u>O<u>2</u> by Retarding its Interfacial Reaction with Electrolyte by Atomic Layer Deposited Al<u>2</u>O<u>3</u>.

Surface and grain boundary coating for stabilizing LiNi0.8Mn0.1Co0.1O2 based electrodes

(Digital Presentation) Simultaneous Transforming Residual Lithium Compounds and Stabilizing Surface Lattice Oxygen for Ni-Rich Cathode Via Atomic Layer Deposition and Post-Annealing

Enhanced Electrochemical Performance of Ni-rich LiNi0.6Co0.2Mn0.2O2 Coated by Molecular Layer Deposition Derived Dual-Functional C-Al2O3 Composite Coating

Reduction of Surface Residual Lithium Compounds for Single-Crystal LiNi0.6Mn0.2Co0.2O2 Via Al2O3 Atomic Layer Deposition and Post-Annealing

Interphase design of LiNi 0.6 Mn 0.2 Co 0.2 O 2 as positive active material for lithium ion batteries via Al 2 O 3 coatings using magnetron sputtering for improved performance and stability

Enhanced Cycling Stability and Rate Capability of Al2O3-Coated NaNi1/3Fe1/3Mn1/3O2 Cathodes for Sodium-Ion Batteries

Modification research of LiAlO2-coated LiNi0.8Co0.1Mn0.1O2 as a cathode material for lithium-ion battery

Enhanced electrochemical performance of Ni-rich cathode material by N-doped LiAlO2 surface modification for lithium-ion batteries

Suppressed Voltage Decay and Improved Electrochemical Performance by Coating LiAl5O8 on the Surface of Li1.2Mn0.54Ni0.13Co0.13O2