Abstract:Metal oxide coatings on cathodes can improve electrochemical stability and longer life cycle of rechargeable Li-ion batteries. Such coatings protects the cathode surface from the direct contact with electrolyte, helps to prevent the formation of SEI (solid electrolyte interphase) layer, reduce ionic dissolution and that results in improved capacity retention, columbic efficiency and longer cycle performance [1,2]. In literature, several oxides and fluorides coatings such as - Al2O3, MgO, TiO2, ZnO, SnO2, ZrO2 and LaF3, AlF3, MgF2, have been suggested which have demonstrated improved capacity retention [3]. Among those coatings, amorphous Al2O3 is probably the most effective coating for capacity retention and stability of the cell [4]. But Al2O3 is a high bandgap insulating material which impose a large resistance on cathode surface resulting smaller charge-discharge capacity at higher C-rates i.e. poor rate performance [5]. Therefore, we propose mixed oxides coatings: Al2O3-Ga2O3, Al2O3-MgO and Al2O3-ZrO2 to improve the conductivity of the coatings. The key reason for selectively choosing Ga, Mg and Zr to introduce into Al2O3 system is following. As Ga2O3 is known for higher electron conductivity, the mixing of Ga should increase the electron conductivity and that can be tuned by varying Ga-content into film. Here Mg, Al, and Zr has valance 2, 3 and 4 respectively, therefore alloying MgO or ZrO2 with Al2O3 will create broken atomic bonds (i.e. increase porosity) in amorphous atomic network and we believe such broken atomic bonds or nano-voids will generate additional path for transporting Li-ion through the coatings resulting less overpotential on cathode surface. Our experiments with such mixed oxides coatings indeed demonstrated improved rate performance and better capacity retention compared to uncoated and Al2O3-coated NMC cathodes, tested in 2032 coin-type cell assembly. Amongst the three different mixed oxide coatings Al2O3-ZrO2 alloy found to be best as shown in Fig.1. An optimum mixing of Zr/(Al+Zr)=0.5 and 5-ALD cycles thickness (~0.5nm) coating helps to retain ~90% of the initial capacity of the NMC-cathode after 100 charge-discharge cycles and also it gives ~300% more improvement in capacity at 10C-rate in contrast with uncoated NMC. To obtain nanoscale mixed-oxides coatings via ALD (as shown in Fig.2), we have demonstrated a new method ‘co-pulsing ALD’ where the metal-precursors are pulsed into reactor at the same time, instead in a sequence. That allows the metal precursors to mix into their gas-phase before reacting on cathode surface providing an intimate mixing into deposited film. The content of mixing can be controlled by varying the partial pressures of the precursors and the total thickness can be controlled by pulse number. In contrast to separate pulsing [6], co-pulsing allows independent control on content of mixing into ternary alloys and total thickness of the coatings at atomic-scale. That enables to tune the cathode surface properties with desirable thickness essential for the battery application. Figure 1

Atomic Layer Deposition of Al2O3-Ga2O3 Alloy Coatings for Li[Ni0.5Mn0.3Co0.2]O2 Cathode to Improve Rate Performance in Li-Ion Battery.

Enhanced Electrochemical Performance of LiNi0.8Co0.15Al0.05O2 Cathode Material via Li2TiO3 Nanoparticles Coating

Nanoscale Mixed-Oxide Coatings for Improving Rate Performance of Li[Ni0.5Mn0.3Co0.2]O2 Cathode in a Rechargeable Li-Ion Battery

Atomic Layer Deposition of Al2O3 on LiNi0.68Co0.10Mn0.22O2 for Enhanced Electrochemical Performance

Advancing Lithium-Ion Batteries' Electrochemical Performance: Ultrathin Alumina Coating on Li(Ni0.8Co0.1Mn0.1)O2 Cathode Materials

Efficacy of atomic layer deposition of Al2O3 on composite LiNi0.8Mn0.1Co0.1O2 electrode for Li-ion batteries

Atomic Layer Deposited MgO: A Lower Overpotential Coating for Li[Ni0.5Mn0.3Co0.2]O2 Cathode

Structural and Electrochemical Study of Al2O3 and TiO2 Coated Li1.2Ni0.13Mn0.54Co0.13O2 Cathode Material Using ALD

Suppressed Voltage Decay and Improved Electrochemical Performance by Coating LiAl5O8 on the Surface of Li1.2Mn0.54Ni0.13Co0.13O2

Atomic Layer Deposited Fluoride Coatings for Li-Ion Battery Cathodes

Ultrathin ZnO Coating for Improved Electrochemical Performance of LiNi0.5Co0.2Mn0.3O2 Cathode Material

Optimized atomic layer deposition of homogeneous, conductive Al2O3 coatings for high-nickel NCM containing ready-to-use electrodes

Enhanced electrochemical properties of Li1·2Ni0·13Co0·13Mn0·54O2 coated with Al2O3 nano-film

Surface Modification of Li(Ni0.6Co0.2Mn0.2)O2 Cathode Materials by Nano-Al2O3 to Improve Electrochemical Performance in Lithium-Ion Batteries

Improving rate capacity and cycling performance of lithium-rich high-Mn Li-1.8[Mn0.7Co0.15Ni0.15]O-2.675 cathode materials by Li2SiO3 coating

Electrochemical Performance of CoAl2O4-Coated LiNi1/3Co1/3Mn1/3O2

Enhanced Cathode Performance: Mixed Al 2 O 3 and LiAlO 2 Coating of Li 1.2 Ni 0.13 Co 0.13 Mn 0.54 O 2

(Digital Presentation) Simultaneous Transforming Residual Lithium Compounds and Stabilizing Surface Lattice Oxygen for Ni-Rich Cathode Via Atomic Layer Deposition and Post-Annealing

Enhanced Cycling Stability and Rate Capability of Al2O3-Coated NaNi1/3Fe1/3Mn1/3O2 Cathodes for Sodium-Ion Batteries

High-performance LiNi0.8Mn0.1Co0.1O2 cathode by nanoscale lithium sulfide coating via atomic layer deposition

Electrochemical Performance of Al<sub>2</sub>O<sub>3</sub>-Coated LiNi<sub>1/3</sub>Co<sub>1/3</sub>Mn<sub>1/3</sub>O<sub>2</sub> Cathode Materials for Li-Ion Batteries