Abstract:The ability to manipulate fluid interfaces, e.g., to retain liquid behind or within porous structures, can be beneficial in multiple applications, including microfluidics, biochemical analysis, and the thermal management of electronic systems. While there are a variety of strategies for controlling the disposition of liquid water via capillarity, such as the use of chemically modified porous adhesive structures and capillary stop valves or surface geometric features, methods that work well for low surface tension liquids are far more difficult to implement. This study demonstrates the microfabrication of a silicon membrane that can retain exceptionally low surface tension fluorinated liquids against a significant pressure difference across the membrane via an array of porous micropillar structures. The membrane uses capillary forces along the triple phase contact line to maintain stable liquid menisci that yield positive working Laplace pressures. The micropillars have inner diameters and thicknesses of 1.5-3 μm and ∼1 μm, respectively, sustaining Laplace pressures up to 39 kPa for water and 9 kPa for Fluorinert™ (FC-40). A theoretical model for predicting the change in pressure as the liquid advances along the porous micropillar structure is derived based on a free energy analysis of the liquid meniscus with capped spherical geometry. The theoretical prediction was found to overestimate the burst pressure compared with the experimental measurements. To elucidate this deviation, transient numerical simulations based on the Volume of Fluid (VOF) were performed to explore the liquid pressure and evolution of meniscus shape under different flow rates (i.e., Capillary numbers). The results from VOF simulations reveal strong dynamic effects where the anisotropic expansion of liquid along the outer micropillar edge leads to an irregular meniscus shape before the liquid spills along the micropillar edge. These findings suggest that the analytical prediction of burst Laplace pressure obtained under quasi-static condition (i.e., equilibrium thermodynamic analysis under low capillary number) is not applicable to highly dynamic flow conditions, where the liquid meniscus shape deformation by flow perturbation cannot be restored by surface tension force instantaneously. Therefore, the critical burst pressure is dependent on the liquid velocity and viscosity under dynamic flow conditions. A numerical simulation using Surface Evolver also predicts that surface defects along the outer micropillar edge can yield up to 50% lower Laplace pressures than those predicted with ideal feature geometries. The liquid retention strategy developed here can facilitate the routing and phase management of dielectric working fluids for application in heat exchangers. Further improvements in the retention performance can be realized by optimizing the fabrication process to reduce surface defects.

A Novel Combined Approach to Better Predict Sealing Performance of Luer Lock Connectivity

Seal Design for Needle-free Syringe Ampoule

An Approach to Calculate Leak Channels and Leak Rates Between Metallic Sealing Surfaces

Theoretical and Experimental Analysis of a Non Contacting Elastohydrodynamic Sealing

Numerical Study on Sealing Performance after Wear of Plug Valve During Opening–closing Process

Research on Sealing Structure and Ground Test of Lunar Sample Return Devices

Experimental Characterization of Electrical Current Leakage in Poly(dimethylsiloxane) Microfluidic Devices

Leakage dynamics of glass bottles on container closure integrity testing: Influence of different laser-drilled microhole geometries

Leakage Analysis and Ground Tests of Knife Edge Indium Seal to Lunar Sample Return Devices

The Percolation of Liquid Through a Compliant Seal—An Experimental and Theoretical Study

Porous micropillar structures for retaining low surface tension liquids

A Surface Connectivity-Based Approach for Leakage Channel Prediction in Static Sealing Interface

Air, Helium and Water Leakage in Rubber O-ring Seals with Application to Syringes

Analysis of Sealing and Leakage Performance of the Subsea Collet Connector with Lens-Type Sealing Structure

Gas Leakage Evaluation of Metallic Sealing Surfaces with Annular Morphology

A Fast and Plug-and-play Mechanical Connector for Microfluidic Chips

Structural Design and Sealing Performance Analysis of a Nanofluidic Self-Heating Unsealing Rubber Cylinder

Evaluating Laser‐Based Microfabrication in Microfluidics: An Experimental and Computational Trial

Cohesion Design-Led Tough Sealants with Controllably Dissolvable Properties

Three-dimensional structure-based approach for the analysis of macroscopic lead structures on sealing counterfaces

Leakage, heat transfer and thermal deformation analysis method for contacting finger seals based on coupled porous media and real structure models