Abstract:Abstract Internal cooling structures for gas turbine engines are becoming more complicated to push the hot gas temperature as high as possible, which, however, allows particulates drawn into the coolant air to be more readily to deposit within these passages and thus greatly affect their flow loss and thermal performance. In this study, internal swirl cooling and jet impingement cooling subjected to particulate deposition were evaluated and compared using a conjugate heat transfer method, with an emphasis on the thermal effects of the insulative deposits. To accomplish the goal, an unsteady conjugate mesh morphing simulation framework was developed and validated, which involved particle tracking in an unsteady fluid flow, particle–wall interaction modeling, conjugate mesh morphing of both fluid and solid domains, and a deposit identification method. The swirl and the jet impingement cooling configurations modeled the internal cooling passage for the leading-edge region of a turbine blade and were investigated in a dust-laden coolant environment at real engine conditions. Coupling effects between the dynamic deposition process and the unsteady flow inside the two cooling channels were examined and the insulative effects of the deposits were quantified by comparing the temperatures on the external and internal surfaces of the metal channel walls, as well as on the deposit layers. Results demonstrated the ability of the newly developed, unsteady conjugate simulation framework to identify the deposits from the original bare wall surface and to predict the insulation effects of the deposits in the dynamic deposition process. The dust almost covered the entire impingement channel, while deposits were only seen in the vicinity of the jets in the swirl channel. Despite this, a dramatical decrease of convection heat transfer was found in the swirl channel because the swirling flow was sensitive to the interruption of the deposits. In contrast, the deposits improved the heat transfer rate in the impingement channel. When the thermal effects of the deposit layer were taken into account, the wall temperatures of both two cooling geometries were substantially elevated, exceeding the allowable temperature of the metal material. Due to the denser deposit coverage, the impingement channel wall had a greater temperature increase than the swirl channel. In terms of flow loss, the presence of the deposits inhibited the swirl intensity by interrupting the swirling flow and thus reduced the friction loss, whereas the pressure loss was improved by the deposits in the impingement cooling.

Deposition of particle pollution in turbulent forced-air cooling

Deposition Rates on Smooth Surfaces and Coagulation of Aerosol Particles Inside a Test Chamber

Unsteady simulations of deposition in a rotor passage of the first-stage turbine for an aero-engine

Simulation of particle deposition on high temperature turbine film cooling blade surface with dynamic mesh morphing

Influence of Wet-Particle Deposition on Air-Side Heat Transfer and Pressure Drop of Fin-and-tube Heat Exchangers

Simulation of surface deposits of micron sand particles in the internal cooling duct with a Gaussian probability density model

Experimental Study of Particle Deposition Characteristics on Wavy Finned-tube Heat Exchanger

Heat transfer properties of dusty radiative cooling surface: Modeling and experimental studies

Experimental Investigation on Particle Deposition and Pressure Drop Characteristics of Slit Fin-and-tube Heat Exchanger

An experimental study on turbine vane Leading-Edge film cooling with deposition

Unsteady simulations of migration and deposition of fly-ash particles in the first-stage turbine of an aero-engine

Quantitative Assessment of the Effect of Surface Deposition and Coagulation on the Dynamics of Submicrometer Particles Indoors

Kinematic Characteristics and Thermophoretic Deposition of Inhalable Particles in Turbulent Duct Flow

CFD simulation of particle deposition in a horizontal turbulent duct flow

Numerical Study Of Particle Deposition In Two Differently Ventilated Rooms

Numerical analysis of particle deposition in ventilation duct

Study on the Particle Deposition Characteristics of Transpiration Cooling Structures with Sintered Wire Mesh

Particulate Deposition Effects on Internal Swirl Cooling of Turbine Blades

Kinematic Characteristics and Thermophoretic Deposition of Inhalable Particles in Temperature Gradient Field

Experimental Study of Solid Particle Deposition in 90° Ventilated Bends of Rectangular Cross Section with Turbulent Flow

Conjugate Heat Transfer Evaluation of Turbine Blade Leading-Edge Swirl and Jet Impingement Cooling With Particulate Deposition