[The bronchial and pulmonary manifestations of aspergillosis other than bronchiectatic aspergilloma].

M. Bariéty,J. Pulet,O. Monod

Abstract:

What problem does this paper attempt to address?

Optimal Design of a Novel Composite Anchorage for Carbon-Fiber-Reinforced Polymer (CFRP) Tendons

Yamin Sun,Kuihua Mei,Shengjiang Sun,Tao Wang,Xiang Ren

DOI: https://doi.org/10.3390/polym14102048

IF: 5

2022-05-18

Polymers

Abstract:In this study, we proposed a novel composite anchorage that considers the anchoring performance and dimension simultaneously. The design concept of this composite anchorage was first introduced, followed by comparison with the traditional inner-cone bond-type anchorage and traditional composite anchorage through theoretical and experimental methods. Then, a parametric study was conducted to determine the influence of different parameters on the anchoring performance, and the optimal design parameters were recommended according to the finite element (FE) and test results. Finally, the practicability of the optimal design parameters were validated through experiments on the anchorage with multiple CFRP tendons. Results showed that the novel composite anchorage could improve the anchoring performance compared with the traditional inner-cone bond-type anchorage by promoting increased anchorage efficiency by 60.4% and, with an ideal failure mode of tendon rupture. Moreover, the novel composite anchorage had smaller dimensions and avoided the presence of a vulnerable position at the junction of the mechanical and bond parts compared with the traditional composite anchorage. In addition, a group of optimal design parameters of this composite anchorage with a pre-tightening force of 130 kN, an inclinational differential angle of 0.1°, an inclination angle of 2.9°, and an embedded length of 30 d~40 d were proposed. The composite anchorage with five CFRP tendons designed with the proposed parameters failed with the rupture of the tendons and exhibited an anchoring efficiency of 1.05. This result showed that the optimal parameters were suitable for this novel composite anchorage to grip multiple tendons. This study can provide an experimental and theoretical basis for designing large-tonnage anchorage for multiple FRP tendons used as hangers or cables in real bridges.

polymer science
Finite Element analysis and experimental study of static performance of multi‐CFRP tendon composite anchorage system

Xue Li,Kuihua Mei,Shiyu Sun,Yuanzhi Wang,Wenke Jia

DOI: https://doi.org/10.1002/pc.28918

IF: 5.2

2024-08-18

Polymer Composites

Abstract:A Novel Composite Anchorage System with Dispersed CFRP Tendons. A novel composite anchorage with dispersed arrangement of carbon fiber‐reinforced polymer (CFRP) tendons was proposed. The bonding length and constraint ratio of the dispersed‐tendon composite anchorage were determined by numerical simulation. Six groups of multi‐CFRP tendon composite anchorage systems (MTCAS) were tested to investigate their static performance. The axial force dispersion coefficient cv and relative slip ratio coefficient δ were proposed to evaluate the static performance of the MTCAS with variables, including pre‐tension load, the inner inclination angle of the sleeve and the modified bonding medium. Results demonstrated that increasing the bonding length and restraint ratio of steel sleeve could improve the stress state of tendon in the anchorage. The anchorage with a bonding length of 280 mm and a constraint ratio of the sleeve of 0.90 can reliably anchor multiple CFRP tendons arranged in a dispersed arrangement. An inner inclination angle of 3.1° of the sleeve can be adopted on the premise that strength utilization ratio is guaranteed and anchorage diameter meets the requirements. An adequate pre‐tension load can reduce the slips of tendons, and the recommended pre‐tension load value should not exceed 0.7 Fptk. The 0.25% basalt fiber‐modified epoxy resin anchorage obtained the highest strength utilization ratio. Highlights A novel composite anchorage with dispersed carbon fiber‐reinforced polymer tendons was designed. New mechanical parameters evaluating anchorage performance were proposed. Basalt fiber (BF)‐modified epoxy resin (ER) can improve anchoring performance. The 0.25% BF‐modified ER anchorage obtained the highest strength utilization ratio. Pre‐tension load should not exceed 0.7 times the theoretical tensile load.

materials science, composites,polymer science
An Efficient Method for Culturing Human Breast Epithelium: Analysis of Results

A. Volpi,Saverio Savini,W. Zoli,Mara Vasinl,S. Morgagni,A. Amadori,R. Volpi,D. Amadori

DOI: https://doi.org/10.1177/030089169107700602

1991-12-01

Tumori

Abstract:We have examined the possibility of obtaining primary cultures from breast tissue utilizing a method especially developed for breast epithelium. The number of specimens able to grow in culture was very high: 82.8%, 64.3 %, 75.0 % and 77.8 %, respectively, for primary breast cancer, skin recurrences, inflammatory breast cancer and normal breast tissue. In our experience, growth was not related to menopausal status or histopathologic type, whereas for skin recurrences, a prior pharmacologic treatment (chemotherapy) of the patient enhanced the growth capacity of the tissue. This culture method could help to study the basic biology of breast epithelia and to improve the chemotherapy approach of breast cancer patients.
Experimental and Numerical Study of Corrugated Anchors for CFRP Plates

Jia-Qi Yang,Husheng Wang,Peng Feng,Guozhen Ding,Lili Wu

DOI: https://doi.org/10.1016/j.conbuildmat.2024.138752

IF: 7.4

2024-01-01

Construction and Building Materials

Abstract:Carbon fibre-reinforced polymer (CFRP) plates are promising materials for cables and prestress tendons in structural engineering for the excellent tensile performance, light in weight and anti-corrosion character. Anchoring has always been the main challenge of this high-performance material due to its anisotropy and brittleness. Corrugated anchors are high-efficiency clamping-type anchorage devices. Nevertheless, premature failure of the CFRP plates can still be observed with this type of anchors, and the anchor efficiency for the corrugated anchors needs further improvement. This paper proposes a novel configuration of corrugated anchors. Experimental tests are then carried out to investigate the influence of the pre-tensioning bolt load and adhesive layer. Consequently, numerical analysis is conducted to reveal the anchoring mechanism. The results indicate the traditional corrugated anchors lead to non-uniform stress distribution in the CFRP plate, and with the proposed configuration the anchor efficiency can be increased up to 100 %.
Static Experimental Study on New Arc Multi-Tendon CFRP Cable Anchorage System

Lijun Jia,Yuchen Yang,Xiao Cong

DOI: https://doi.org/10.3390/buildings13030669

IF: 3.324

2023-03-03

Buildings

Abstract:CFRP has the potential to replace steel cables in large-span cable-stayed bridges due to its high strength and lightweight material properties. However, the weak lateral force performance of CFRP material creates the challenge of anchoring. This study introduces a new inner cone + arc + straight cylinder bond-type anchorage system to optimize CFRP tendons' force state. Experimental and finite element analyses verified the new anchoring system's performance. In static load tensile tests, six groups of seven CFRP tendon anchorage systems with different sleeve grooves were used to study the failure mode and load–strain variation law. The difference in mechanical properties between the new and traditional anchorage is evaluated in the finite element analysis. The results indicate that the new anchorage system can lower the stress concentration in the anchorage zone and enhance anchorage performance. The groove design of the sleeve can effectively increase the anchoring efficiency, where the groove depth is proportional to the anchoring efficiency and the groove spacing is inversely proportional to the anchoring efficiency. The magnitude of the stress inhomogeneity in the multi-tendon anchoring system during tensioning is proportional to the beginning conditions and the load size. When the inner wall of the sleeve becomes more abrasive, the force heterogeneity of the anchorage system reduces. The tests and finite element analysis show that the new anchoring may improve stress distribution and anchorage efficiency. In engineering practice, it can be utilized as a dependable anchorage system.

construction & building technology,engineering, civil
Design and evaluation of a new bond-type anchorage system for fiber reinforced polymer tendons

Burong Zhang,Brahim Benmokrane

DOI: https://doi.org/10.1139/l03-062

2004-01-01

Canadian Journal of Civil Engineering

Abstract:Corrosion resistance, high strength, and advantageous strength-to-weight ratio enable fiber reinforced polymers (FRPs) to have substantial potential to replace steel tendons in prestressed applications. One of the main technical obstacles to wide use of FRPs in the construction industry is the methodology to anchor FRP tendons to achieve their full strength. High tensile to compression and shear strength ratios make it necessary to develop a new anchorage design concept for FRP tendons. This paper gives a literature review of bond-type anchorage systems and the mechanics of stress transfer by bond from FRP tendons to grout and reports an experimental study on a newly developed bond-type anchorage system with carbon fiber reinforced polymer (CFRP) Leadline 8-mm-diameter rods. The test program consisted of nine monotonic tensile tests, two pullout tests, and two proving tests on the anchorage system with Leadline single- or 9-rod tendons. The test results showed that the developed anchorage system with 250-mm bond length ensures full development of the tensile strength of Leadline mono-rod tendons. The bond strength of Leadline 9-rod tendons is 14 MPa for a bond length of 95 mm, 62% of that of mono-rod ones with a bond length of 80 mm. The anchorage system with a 400-mm bond length gives at least 90% of the tensile strength of Leadline 9-rod tendons and also demonstrates an acceptable sustained loading behaviour in accordance with existing codes.Key words: anchorage, bond stress, creep, grout, polymers, rod, slip, tendon.

engineering, civil
EXPERIMENTAL STUDY ON FLEXURAL BEHAVIOR OF REINFORCED CONCRETE BEAMS PRE-STRESSED WITH CFRP TENDONS

Jian-lin HU,Long-wei WANG,Long-cheng CAO,Xiao-yan SUN

DOI: https://doi.org/10.3969/j.issn.1001-6864.2013.05.014

2013-01-01

Abstract:In order to investigate the flexural behavior of reinforced concrete bridge girder prestressed with external carbon fiber reinforced polymer(CFRP) tendons,the experimental data of different type of bridge girders prestressed with external tendons were analysized.The investigation results indicate that the flexural behavior of concrete girders with externally prestressed CFRP tendons are similar to that with external steel tendons in many aspects.The external prestressed CFRP tendons can improve bearing capacity and reduce their deformation and crack remarkably.The initial loading state on the girders before tendon jacking has no significant effect on the capacity and deflection.The stress improvement of CFRP appeared after the yield of non-prestressing reinforcing steel rebar.
Experimental investigation and damage evaluation of a novel bond type anchorage for carbon fiber reinforced polymer tendons

Shiyuan Ju,Dongsheng Li,Jinqing Jia

DOI: https://doi.org/10.1007/s13349-022-00626-9

2022-09-04

Journal of Civil Structural Health Monitoring

Abstract:The bond type anchorage is most suitable for anchoring carbon fiber reinforced polymer (CFRP) tendons, but its shape causes stress concentration. In addition, the failure modes of bonded anchors are difficult to observe and the damage process is difficult to analyze. The aim of this study was to address the above problems. To relieve the stress concentration, a novel arcuate-cone bond type anchorage was designed in this study. The failure modes and load-slip curves were obtained by tension tests on a group of anchors. The test results indicated that the stress concentration can be effectively alleviated. Acoustic emission technique was used to monitor the damage process of bond type anchorages under tension load. By analyzing the acoustic emission data, the damage process of bond type anchorage can be divided into three stages and the different failure modes can be identified. Finally, the failure mechanism of bonded anchorages was discussed based on the test results and monitoring data.

engineering, civil
Structural Analyses of Extruded CFRP Tendon-Anchor System and Applications in Thin-Walled Aluminum/cfrp Bridge

Pengcheng Zhu,Pengcheng Ai,Yinzhi Zhou,Longxing Xu,Hualin Fan

DOI: https://doi.org/10.1016/j.tws.2018.02.029

IF: 5.881

2018-01-01

Thin-Walled Structures

Abstract:Pre-stressed carbon fiber reinforced polymer (CFRP) tendon system is developed. Extrusion method guarantees the strength of the CFRP tendon could be fully used in strengthening. The pre-stressed CFRP tendons are applied to strengthen aluminum beams and portable aluminum bridge to improve the flexural rigidity and load carrying capacity of these structures and the improvements are revealed by the experiments. Applying extruded CFRP tendon-anchor system, the load carrying ability of the pre-stressed aluminum bridge has an improvement of 25%. Structural models are proposed to investigate the pre-stressing effects, including the deflection and the load capacity under different design criteria. Finite element method (FEM) is applied to analyze the nonlinear behavior of the pre-stressed beam and reveal the plastic torsional buckling failure style. All these analyses agree well with the experiments and suggest accurate methods to design pre-stressed aluminum/CFRP structures.
Experimental Research on Bonded Anchorage of Carbon Fiber Reinforced Polymer Prestressed Strands

Liqiang Jia,Bo Wang,T Tafsirojjaman

DOI: https://doi.org/10.3390/polym14194015

2022-09-25

Abstract:Aiming at the problems of a large number of corrosion and fatigue damage of the current prestressed steel strands, this paper adopts carbon fiber-reinforced composite (CFRP) strand with better corrosion resistance and fatigue resistance and uses it in concrete structures. The bond anchorage is usually used to anchor CFRP tension members, which bonds the CFRP through the binding medium. Through experimental research on the CFRP strand bond anchorage, the inner taper of the CFRP prestressed strand cone was anchored and the influence of different anchor lengths and bonding media on the anchorage performance was determined. The test results demonstrate that the taper of the conical anchorage described in this paper is a key factor affecting its anchorage performance and increasing the inner taper within a certain range is beneficial to improving the anchorage performance of the conical anchorage. The bonded anchorage of the CFRP prestressed strand with a 200 mm anchor is the most reliable and efficient, as the taper of the 200 mm anchor is the largest. The average anchoring efficiency coefficient of the 200 mm anchor was 96.4%, which is 3.7% and 2.6% higher than the average anchoring efficiency coefficient of 220 mm and 250 mm anchors, respectively. The anchoring efficiency of the anchor is also high (94.1%) when the epoxy resin mortar is used as the bonding medium. Moreover, after an appropriate amount of quartz sand is added to the epoxy resin, the overall comprehensive performance of the anchor can be improved to a certain extent and the stress of the CFRP strand can be improved. The coupling between ultra-high-performance concrete dry mix (UHPC-GJL) and CFRP strand materials is not suitable for UHPC-GJL being used, as its binding medium as the average anchoring efficiency coefficient is only 44.5% when UHPC-GJL is used as the anchor bonding medium.
A novel anchor method for large tonnage CFRP cable: Anchorage design and full-scale experiment

Wenchao Zhang,Lijun Jia,Kedian Luo,Xiaozhu Teng

DOI: https://doi.org/10.1016/j.compstruct.2024.118004

IF: 6.3

2024-05-01

Composite Structures

Abstract:This study introduces a novel three-segment CFRP cable anchorage to address stress concentration challenges in CFRP cable anchors. The anchorage features a continuously varying inner cone angle along the anchor length to prevent excessive radial stress on the CFRP cable. The radial stress distribution is theoretically analyzed, followed by a numerical simulation design using the Tsai-Wu failure criterion and the anchor system's equivalent stiffness as evaluation indices. The results demonstrate a 47.06 % and 45.73 % reduction in the radial stress peak of the novel anchorage compared to the inner cone and inner cone + straight cylinder anchorage, respectively. Importantly, beyond an anchor length 23 times the equivalent diameter of the CFRP tendon, increasing length has a marginal impact on anchor efficiency but diminishes equivalent stiffness. Positive effects are observed by increasing the inner cone segment proportion and adjusting the inner cone angle within the 2° to 4° range. Conversely, increasing the bonding medium thickness reduces anchor efficiency and equivalent stiffness. Experimental verification indicates the anchor system achieving 99.83 % anchor efficiency. Moreover, the axial strain of CFRP tendons in the anchor zone exhibits a linear trend along the anchor length, with test stresses at corresponding positions consistent with FE calculation results.

mechanics,materials science, composites
Management of an R&D planning process utilizing an advisory group

F. Denny

DOI: https://doi.org/10.1109/TEM.1980.6447386

IF: 8.702

1980-05-01

IEEE Transactions on Engineering Management

Abstract:Emphasizes the practical aspects of selecting projects or programs for funding utilizing an experience-based resource group or team of experts. A process is proposed for identifying research and development needs in a systematic manner which attempts to minimize impulsiveness, while maximizing careful review and decision making. The methodology discussed has proven to be effective at clarifying problem areas and producing group concensus. Common pitfalls and means to circumvent counterproductive efforts and inefficiencies are cited.
Evaluation of the properties and applications of FRP bars and anchors: A review

Yuhang Ren,Hongguang Wang,Zhongzhi Guan,Kainan Yang

DOI: https://doi.org/10.1515/rams-2022-0287

2023-01-01

REVIEWS ON ADVANCED MATERIALS SCIENCE

Abstract:Abstract The performance deterioration of steel anchors caused by steel corrosion is becoming more serious in slope anchorage applications. Therefore, the fiber reinforced plastic (FRP) composites have become a substitute material for traditional anchorage structures due to their advantages of low price, lightweight, high strength, and corrosion resistance. Numerous studies have proven that FRP anchors have better anchoring capacity than traditional steel anchors in practical engineering and are not as susceptible to environmental influences. This review mainly introduced the mechanical properties of FRP, focuses on the current research progress and innovation of FRP anchor in anchorage engineering, then provides a basis for the design of FRP anchor. In this study, the failure characteristics and problem of insufficient bonding strength of the first interface of FRP anchor anchoring slope were discussed, and the improvement was introduced. It will be conducive to the extension and application of FRP composites as structural materials in civil engineering. A detailed introduction is also given to biomaterials, which are mainly derived from nature and which will not only reduce waste disposal problems and environmental pollution but will also replace conventional applications. Finally, there will be an important reference and value for the development of green and sustainable engineering structures.

materials science, multidisciplinary,nanoscience & nanotechnology
Novel Self-Anchored CFRP Cable System: Concept and Anchorage Behavior

Pengcheng Ai,Peng Feng,Hongwei Lin,Pengcheng Zhu,Guozhen Ding

DOI: https://doi.org/10.1016/j.compstruct.2021.113736

IF: 6.3

2021-01-01

Composite Structures

Abstract:CFRP cables are promising to be utilized in bridge engineering, but their effective anchorage remains a chal-lenge for engineers. To solve this problem, novel self-anchored CFRP cables with different anchorage config-urations were designed and tested, with main variables including the radius, thickness, and slope of the CFRP loop at the anchorages. The results indicate that the mechanical behavior of the self-anchored cables is mainly determined by the thickness and radius of the CFRP loop and by increasing these characteristics, the cable's material strength can be fully exploited. With optimized anchorage configurations, the anchor effi-ciency of the proposed self-anchor CFRP cable system can reach 95% or larger. Additionally, finite element analysis was conducted, with good agreement between the numerical and experimental results. Finally, the influence of the radius and thickness of the CFRP loop on the anchoring capacity and the nominal anchor effi-ciency was further discussed based on an orthotropic thick-walled cylinder model.
Intrahepatic cholangiocarcinoma: indication for transplantation.

A. Pascher,S. Jonas,P. Neuhaus

DOI: https://doi.org/10.1007/S00534-002-0731-9

2003-08-01

Journal of Hepato-Biliary-Pancreatic Surgery

Abstract:
An Experimental Study of Self-anchored Combined CFRP Cables

Guozhen Ding,Chao Wu,Peng Feng

DOI: https://doi.org/10.2749/manchester.2024.1206

2024-01-01

Abstract:Carbon Fiber Reinforced Polymer (CFRP) is an advanced material known for its lightweight, high strength, corrosion resistance, and fatigue durability, making it an ideal choice for cables in structural engineering. However, being an anisotropic material, CFRP faces challenges in anchoring due to its lower transverse mechanical properties compared to its tensile strength. In response to this issue, this paper designs and tests a self-anchored combined CFRP cable with variations in anchorage type, joint type, and CFRP plate thickness. The results reveal that interface shear stress causes delamination failure in the anchorage, leading to lower- than-expected load-bearing capacity. Through improved design and processing methods, interface damage in the anchorage is reduced, enhancing load-bearing capacity and achieving an ideal failure mode of cable body rupture.
Experimental Research and Analysis on Fatigue Life of Carbon Fiber Reinforced Polymer (CFRP) Tendons

Shoutan Song,Hua Zang,Ning Duan,Juntao Jiang,Song,Zang,Duan,Jiang

DOI: https://doi.org/10.3390/ma12203383

IF: 3.4

2019-10-16

Materials

Abstract:The fatigue life of carbon fiber reinforced polymer (CFRP) tendons was studied in this paper. A new wedge-type anchorage system was applied to the fatigue test of CFRP tendons and demonstrated an excellent fatigue resistance. In the test and analytical data, the fatigue stress ranged from 200 MPa to 800 MPa, and maximum stresses from 0.37 to 1.0 fu (fu = ultimate tensile strength of CFRP tendons) were determined. The main work and results were that the stress range and stress level (maximum stress) were two key parameters affecting the fatigue life of CFRP tendons. A bilinear equation and a linear equation considering the fatigue life of CFRP tendons jointly affected by the stress range and the maximum stress were established. The error of predicted results and test results was 0.038 and 0.083, respectively, both representing good prediction accuracy. The predicted results of Whitney's method showed that, at a 95% confidence level, when the stress range was 200 MPa, 400 MPa, and 600 MPa, the maximum stress limit of CFRP tendons, which were not broken in a fatigue test of 2 million times, was 63.9% fu, 53.0% fu, and 36.8% fu, respectively.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,metallurgy & metallurgical engineering
Uniaxial Tensile Behavior of Anchored Carbon Fabric-Reinforced Cementitious Matrix Plates

Yusen Wu,Zhiyu Xie,Dawei Zhang,Jihua Zhu,Haixuan Li

DOI: https://doi.org/10.1061/jmcee7.mteng-14941

IF: 3.2

2023-01-01

Journal of Materials in Civil Engineering

Abstract:The fabric-reinforced cementitious matrix (FRCM) has begun to show great application prospects in structural strengthening, especially for seismic strengthening. However, a poor monolithic response of fabric and mortar limits the utility ratio of the fabric and the mechanical properties of FRCM. A simple, fast, and efficient method for improving the bonding properties of the fabric-mortar interface to enhance the performance of the FRCM plate remains to be investigated. In this study, uniaxial tensile tests on 42 carbon fabric-reinforced cementitious matrix (C-FRCM) plates with anchored carbon fiber bundles were performed to analyze the influence of anchorages on their mechanical properties, and to compare them to the prior results of pull-out tests of anchored carbon fiber bundles. The results show that the ultimate tensile stress, the energy dissipation, and the fiber utility ratio can be increased significantly after anchoring, but the anchorage cannot fully restrict the slippage of fiber fabrics. The effect of other variables, such as the bond length of steel plates, the number of fabric layers, and mortar strength, were also tested and discussed.
Anchoring and stressing methods for prestressed FRP plates: State-of-the-art review

Xinquan Chang,Xin Wang,Changyuan Liu,Zhishen Wu,Mohammad Noori

DOI: https://doi.org/10.1177/07316844241258864

IF: 3.1

2024-06-26

Journal of Reinforced Plastics and Composites

Abstract:Journal of Reinforced Plastics and Composites, Ahead of Print. Prestressing of the fiber-reinforced polymer (FRP) plate is applied to fully extend the high-strength performance of the FRP plate in structure reinforcement. Anchoring methods and stressing are the two main issues for prestressed FRP plates. Although a number of methods concerning those two main issues have been developed, the literature lacks a systematic review on the existing methods for FRP plates anchoring and stressing. This article compares the comprehensive performance of different FRP plates, recommending BFRP plates as more suitable for use in prestressed tensioning systems. It contrasts the principles and applicability of various anchoring devices, suggesting that wedge-type clip anchors and flat-type anchors show promising development prospects. Additionally, addressing stress concentration in the anchorage zones of low-modulus FRP plates is key to enhancing anchoring efficiency. Ultimately, the paper evaluates tensioning methods for FRP plates, identifying "the method of jacking against the strengthened component" as the most promising, yet it requires innovation in terms of dimensions and positioning of the tensioning frame to enhance its applicability to specific engineering needs.

materials science, composites,polymer science
Development and validation of a RP-HPLC method for the determination of gentamicin sulfate and its related substances in a pharmaceutical cream using a short pentafluorophenyl column and a charged aerosol detector.

A. Joseph,A. Rustum

DOI: https://doi.org/10.1016/j.jpba.2009.09.002

IF: 3.571

2010-02-05

Journal of Pharmaceutical and Biomedical Analysis

Abstract:

[The bronchial and pulmonary manifestations of aspergillosis other than bronchiectatic aspergilloma].

Optimal Design of a Novel Composite Anchorage for Carbon-Fiber-Reinforced Polymer (CFRP) Tendons

Finite Element analysis and experimental study of static performance of multi‐CFRP tendon composite anchorage system

An Efficient Method for Culturing Human Breast Epithelium: Analysis of Results

Experimental and Numerical Study of Corrugated Anchors for CFRP Plates

Static Experimental Study on New Arc Multi-Tendon CFRP Cable Anchorage System

Design and evaluation of a new bond-type anchorage system for fiber reinforced polymer tendons

EXPERIMENTAL STUDY ON FLEXURAL BEHAVIOR OF REINFORCED CONCRETE BEAMS PRE-STRESSED WITH CFRP TENDONS

Experimental investigation and damage evaluation of a novel bond type anchorage for carbon fiber reinforced polymer tendons

Structural Analyses of Extruded CFRP Tendon-Anchor System and Applications in Thin-Walled Aluminum/cfrp Bridge

Experimental Research on Bonded Anchorage of Carbon Fiber Reinforced Polymer Prestressed Strands

A novel anchor method for large tonnage CFRP cable: Anchorage design and full-scale experiment

Management of an R&D planning process utilizing an advisory group

Evaluation of the properties and applications of FRP bars and anchors: A review

Novel Self-Anchored CFRP Cable System: Concept and Anchorage Behavior

Intrahepatic cholangiocarcinoma: indication for transplantation.

An Experimental Study of Self-anchored Combined CFRP Cables

Experimental Research and Analysis on Fatigue Life of Carbon Fiber Reinforced Polymer (CFRP) Tendons

Uniaxial Tensile Behavior of Anchored Carbon Fabric-Reinforced Cementitious Matrix Plates

Anchoring and stressing methods for prestressed FRP plates: State-of-the-art review

Development and validation of a RP-HPLC method for the determination of gentamicin sulfate and its related substances in a pharmaceutical cream using a short pentafluorophenyl column and a charged aerosol detector.