Foot-and-mouth disease in white-tailed deer: clinical signs and transmission in the laboratory.

J. McVicar,P. Sutmoller,D. Ferris,C. H. Campbell

Abstract:

What problem does this paper attempt to address?

Femtometer-amplitude imaging of coherent super high frequency vibrations in micromechanical resonators

Lei Shao,Vikrant J. Gokhale,Bo Peng,Penghui Song,Jingjie Cheng,Justin Kuo,Amit Lal,Wen-Ming Zhang,Jason J. Gorman

DOI: https://doi.org/10.1038/s41467-022-28223-w

IF: 16.6

2022-02-04

Nature Communications

Abstract:Abstract Dynamic measurement of femtometer-displacement vibrations in mechanical resonators at microwave frequencies is critical for a number of emerging high-impact technologies including 5G wireless communications and quantum state generation, storage, and transfer. However, the resolution of continuous-wave laser interferometry, the method most commonly used for imaging vibration wavefields, has been limited to vibration amplitudes just below a picometer at several gigahertz. This is insufficient for these technologies since vibration amplitudes precipitously decrease for increasing frequency. Here we present a stroboscopic optical sampling approach for the transduction of coherent super high frequency vibrations. Phase-sensitive absolute displacement detection with a noise floor of 55 fm/√Hz for frequencies up to 12 GHz is demonstrated, achieving higher bandwidth and significantly lower noise floor simultaneously compared to previous work. An acoustic microresonator with resonances above 10 GHz and displacements smaller than 70 fm is measured using the presented method to reveal complex mode superposition, dispersion, and anisotropic propagation.

multidisciplinary sciences
Stroboscopic Interferometer for Dynamic MEMS Characterization

郭彤,胡春光,胡晓东,栗大超,金翠云,傅星,胡小唐

DOI: https://doi.org/10.3969/j.issn.1672-6030.2004.04.010

2004-01-01

Abstract:A key purpose for testing MEMS i s to provide data feedback of measurements to the design and simulation in t he process of development, where high-speed visualization of dynamic propertie s of MEMS devices is a very important aspect. This paper describes a computer- controlled stroboscopic interferometer system for measuring out-of-plane m otions of MEMS structures with nanometer resolution. The system uses a modified phase-shifting interferometric algorithm and a pulsed laser diode(LD) serves as the stroboscopic light source, permitting measurement of large-amplitude out- of-plane motions(above ten micrometers) below 1 MHz. The high out-of-plane se nsitivity of the method makes it particularly suitable for characterizing microm echanical (optical) elements. This paper illustrates the capabilities of the sy stem with a study of the dynamic behavior of a polysilicon micro-resonator.
Tunable-illumination for Laser Fourier Ptychographic Microscopy Based on a Background Noise-Reducing System

Xiao Tao,Jinlei Zhang,Chenning Tao,Peng Sun,Rengmao Wu,Zhenrong Zheng

DOI: https://doi.org/10.1016/j.optcom.2020.125764

IF: 2.4

2020-01-01

Optics Communications

Abstract:It is inherently difficult for a conventional microscopic imaging system to produce images with both wide field of view (FOV) and high-resolution because of its limited space bandwidth product. Fourier ptychographic microscopy (FPM) has been developed to overcome this limitation by using angle-varied illumination to enhance the performance of the system. In this paper, we propose a FPM imaging approach that employs a laser source with a newly developed illumination control optical system. The proposed system consists of a digital micromirror device and a zoom system with a condenser lens to provide sample illumination with angle-varied pattern directions and controllable pattern sizes. In addition, a total internal reflection prism is employed in the system to remove unexpected background noise and extend the FOV for reconstruction. The proposed system is validated against a USAF resolution target and a biological sample, and as a result reconstructs images with higher resolution and more details once the positional misalignment correction algorithm is employed. We envision that the proposed FPM system will be suitable for high-speed imaging applications.
Micro-vibration measuring technology based on heterodyne interference

Dan Liu,Bin Zheng,Hualing Guo,Hui Liu,Naiqiang Liu

DOI: https://doi.org/10.5768/JAO201435.0503006

2014-01-01

Journal of Applied Optics

Abstract:Aiming at the problem that the micro-vibration based on heterodyne interference has low stability and is easily impacted by environmental noise ,the ideas of optical path improve-ment were given .According to the difference principle ,the single optical path was converted to a double optical path ,in which the environmental noise was eliminated ;The elliptically po-larized light was changed into linearly polarized light to improve the interference signal ampli-tude by the polarization splitting prism (PBS);The acousto-optic modulator(AOM ) was im-proved to inhibit frequency drift ;The stray light was suppressed by using diaphragm filters so as to improve the system signal-noise ratio (SNR) .The verification experiments were conduc-ted through detecting 5 kHz piezoelectric vibration signal and 2 .5 M Hz laser ultrasonic signal . Experimental results indicate that signal is stable and has no ripple ,the resolution is 2 .3 nm and the SNR has improved by 16 .7 times .The amplitudes of double-channel heterodyne inter-ferometer signal is 552 mV and 736 mV ,respectively ,which are larger than traditional one nearly 10 times ,it is advantageous to measure nanometer micro-vibration signals .
Nanoscale imaging of super-high-frequency microelectromechanical resonators with femtometer sensitivity

Daehun Lee,Shahin Jahanbani,Jack Kramer,Ruochen Lu,Keji Lai

DOI: https://doi.org/10.1038/s41467-023-36936-9

IF: 16.6

2023-03-03

Nature Communications

Abstract:Implementing microelectromechanical system (MEMS) resonators calls for detailed microscopic understanding of the devices, such as energy dissipation channels, spurious modes, and imperfections from microfabrication. Here, we report the nanoscale imaging of a freestanding super-high-frequency (3 – 30 GHz) lateral overtone bulk acoustic resonator with unprecedented spatial resolution and displacement sensitivity. Using transmission-mode microwave impedance microscopy, we have visualized mode profiles of individual overtones and analyzed higher-order transverse spurious modes and anchor loss. The integrated TMIM signals are in good agreement with the stored mechanical energy in the resonator. Quantitative analysis with finite-element modeling shows that the noise floor is equivalent to an in-plane displacement of 10 fm/√Hz at room temperatures, which can be further improved under cryogenic environments. Our work contributes to the design and characterization of MEMS resonators with better performance for telecommunication, sensing, and quantum information science applications.

multidisciplinary sciences
Integrated Measurement Of Micro Motions For Mems Dynamic Performance Analysis

Dc Li,Yl Feng,Sj Jin,Cy Jin,Yl Hao,Dc Zhang

2002-01-01

Abstract:A fully integrated optical and electrical measurement system made of off-the-shelf optical components and electrical instruments that characterizes the micro motions for MEMS dynamic performance at the wafer/die level automatically is presented. Both periodic and non-periodic in-plane micro motions could be measured by the blur-synthesis method based on the machine vision technology. The periodic out-of-plane micro motions could be estimated by the laser stroboscopic phase-shifting interferometry with the digital image processing technology. Some improved algorithms together with the sub pixel method and 2D waveform transform technology are bought forward and experimented for the measurement of micro motions with higher resolution. The methods could measure micro motions up to tens of KHz in real time with nano resolution and the characterization is both in situ and nondestructive. Based upon the virtual instrument technology, the measurement system with friendly user interfaces, open hardware and software architectures and expansible features could be used practically in MEMS R&D field and more improvements to this system could be made continually.
Mirrorless MEMS imaging: a nonlinear vibrational approach utilizing aerosol-jetted PZT-actuated fiber MEMS scanner for microscale illumination

Wei-Chih Wang,Ming-Yao Li,Kuan-Chang Peng,Yi-Feng Hsu,Benjamin Estroff,Pao-Yun Yen,David Schipf,Wen-Jong Wu

DOI: https://doi.org/10.1038/s41378-023-00646-5

2024-01-22

Microsystems & Nanoengineering

Abstract:Abstract This study introduces a novel image capture and lighting techniques using a cutting-edge hybrid MEMS scanner system designed for compact microscopic imaging. The scanner comprises a tapered optical fiber waveguide and innovative aerosol-jet printed PZT (lead zirconate titanate) bimorph push-pull actuators on a stainless-steel substrate, effectively addressing issues that are commonly associated with PZT on silicon substrates such as fracture and layer separation. By leveraging nonlinear vibration, the scanner achieves a spiral scan pattern from a single signal input, in addition to the expected two-dimensional scanning and target illumination from two phase-shifted inputs. This capability is further enhanced by a novel process to taper the optical fiber, which reduces illumination scattering and tunes the fiber to the resonant frequencies of the scanner. The precisely tapered tip enables large fields of view while maintaining independent 2-axis scanning through one-degree-of-freedom actuation. Experimental validation showcases the successful generation of a spiral scan pattern with a 60 μm diameter scan area and a 10 Hz frame rate, effectively reconstructing scanned images of 5 μm lines, cross patterns (15 μm in length with a 5 μm gap), and structures of a Psychodidae wing.

nanoscience & nanotechnology,instruments & instrumentation
Single-particle vibrational spectroscopy using optical microresonators

Shui-Jing Tang,Mingjie Zhang,Jialve Sun,Jia-Wei Meng,Xiao Xiong,Qihuang Gong,Dayong Jin,Qi-Fan Yang,Yun-Feng Xiao

DOI: https://doi.org/10.1038/s41566-023-01264-3

2023-05-23

Abstract:Vibrational spectroscopy is a ubiquitous technology that derives the species, constituents, and morphology of an object from its natural vibrations. However, the vibrational spectra of mesoscopic particles - including most biological cells - have remained hidden from existing technologies. These particles are expected to vibrate faintly at megahertz to gigahertz rates, imposing unpractical sensitivity and resolution for current optical and piezoelectric spectroscopy. Here we demonstrate the real-time measurement of natural vibrations of single mesoscopic particles using an optical microresonator, extending the reach of vibrational spectroscopy to a new spectral window. Conceptually, a spectrum of vibrational modes of the particles is stimulated photoacoustically, and correlated to a high-quality-factor optical resonance for the ultrasensitive readout. Experimentally, this scheme is testified by measuring mesoscopic particles with different constituents, sizes, and internal structures, showing an unprecedented signal-to-noise ratio of 50 dB and detection bandwidth over 1 GHz. This new technology is further applied for the biomechanical fingerprinting of single microbial cells with different species and living states. The present method opens up new avenues to study single-particle mechanical properties in vibrational degrees of freedom, and may find applications in photoacoustic sensing and imaging, cavity optomechanics and biomechanics.

Optics,Applied Physics,Biological Physics
Phase Sensitive Imaging of 10 GHz Vibrations in an AlN Microdisk Resonator

Zhen Shen,Xu Han,Chang-Ling Zou,Hong X. Tang

DOI: https://doi.org/10.1063/1.4995008

IF: 1.6

2017-01-01

Review of Scientific Instruments

Abstract:We demonstrate a high frequency phase-sensitive heterodyne vibrometer, operating up to 10 GHz. Using this heterodyne vibrometer, the amplitude and phase fields of the fundamental thickness mode, the radial fundamental, and the 2nd-order modes of an AlN optomechanical microdisk resonator are mapped with a displacement sensitivity of around 0.36pm/Hz. The simultaneous amplitude and phase measurement allow precise mode identification and characterization. The recorded modal frequencies and profiles are consistent with numerical simulations. This vibrometer will be of great significance for the development of high frequency mechanical devices.
Real-time imaging of standing-wave patterns in microresonators

Haochen Yan,Alekhya Ghosh,Arghadeep Pal,Hao Zhang,Toby Bi,George Ghalanos,Shuangyou Zhang,Lewis Hill,Yaojing Zhang,Yongyong Zhuang,Jolly Xavier,Pascal DelHaye

DOI: https://doi.org/10.1073/pnas.2313981121

2024-01-15

Abstract:Real-time characterization of microresonator dynamics is important for many applications. In particular it is critical for near-field sensing and understanding light-matter interactions. Here, we report camera-facilitated imaging and analysis of standing wave patterns in optical ring resonators. The standing wave pattern is generated through bi-directional pumping of a microresonator and the scattered light from the microresonator is collected by a short-wave infrared (SWIR) camera. The recorded scattering patterns are wavelength dependent, and the scattered intensity exhibits a linear relation with the circulating power within the microresonator. By modulating the relative phase between the two pump waves, we can control the generated standing waves movements and characterize the resonator with the SWIR camera. The visualized standing wave enables subwavelength distance measurements of scattering targets with nanometer-level accuracy. This work opens new avenues for applications in on-chip near-field (bio-)sensing, real time characterization of photonic integrated circuits and backscattering control in telecom systems.

Optics
Single-particle Photoacoustic Vibrational Spectroscopy Using Optical Microresonators

Shui-Jing Tang,Mingjie Zhang,Jialve Sun,Jia-Wei Meng,Xiao Xiong,Qihuang Gong,Dayong Jin,Qi-Fan Yang,Yun-Feng Xiao

DOI: https://doi.org/10.1038/s41566-023-01264-3

IF: 35

2023-01-01

Nature Photonics

Abstract:Vibrational spectroscopy is a ubiquitous technology that derives the species, constituents, and morphology of an object from its natural vibrations. However, the vibrational spectra of mesoscopic particles - including most biological cells - have remained hidden from existing technologies. These particles are expected to vibrate faintly at megahertz to gigahertz rates, imposing unpractical sensitivity and resolution for current optical and piezoelectric spectroscopy. Here we demonstrate the real-time measurement of natural vibrations of single mesoscopic particles using an optical microresonator, extending the reach of vibrational spectroscopy to a new spectral window. Conceptually, a spectrum of vibrational modes of the particles is stimulated photoacoustically, and correlated to a high-quality-factor optical resonance for the ultrasensitive readout. Experimentally, this scheme is testified by measuring mesoscopic particles with different constituents, sizes, and internal structures, showing an unprecedented signal-to-noise ratio of 50 dB and detection bandwidth over 1 GHz. This new technology is further applied for the biomechanical fingerprinting of single microbial cells with different species and living states. The present method opens up new avenues to study single-particle mechanical properties in vibrational degrees of freedom, and may find applications in photoacoustic sensing and imaging, cavity optomechanics and biomechanics.
Multi-frame interferometric imaging with a femtosecond stroboscopic pulse train for observing irreversible phenomena

Dmitro Martynowych,David Veysset,A. A. Maznev,Yuchen Sun,Steven E. Kooi,Keith A. Nelson

DOI: https://doi.org/10.1063/1.5140446

IF: 1.6

2020-03-01

Review of Scientific Instruments

Abstract:We describe a high-speed single-shot multi-frame interferometric imaging technique enabling multiple interferometric images with femtosecond exposure time over a 50 ns event window to be recorded, following a single laser-induced excitation event. The stroboscopic illumination of a framing camera is made possible through the use of a doubling cavity that produces a femtosecond pulse train that is synchronized to the gated exposure windows of the individual frames of the camera. The imaging system utilizes a Michelson interferometer to extract phase and ultimately displacement information. We demonstrate the method by monitoring laser-induced deformation and the propagation of high-amplitude acoustic waves in a silicon nitride membrane. The method is applicable to a wide range of fast irreversible phenomena such as crack branching, shock-induced material damage, cavitation, and dielectric breakdown.

instruments & instrumentation,physics, applied
Transient vibration imaging with time-resolved synthetic holographic confocal microscopy

Martin Schnell,P. Scott Carney,Rainer Hillenbrand

DOI: https://doi.org/10.1364/OE.26.026688

2019-04-09

Abstract:We introduce a new modality for dynamic phase imaging in confocal microscopy based on synthetic optical holography. By temporal demultiplexing of the detector signal into a series of holograms, we record time-resolved phase images directly in the time domain at a bandwidth as determined by the photo detector and digitizer. We demonstrate our method by optical imaging of transient vibrations in an atomic force microscope cantilever with 100 ns time resolution, and observe the dynamic deformation of the cantilever surface after excitation with broadband mechanical pulses. Temporal Fourier transform of a single data set acquired in 4.2 minutes yields frequency and mode profile of all excited out-of-plane vibration modes with sub-picometer vertical sensitivity and sub-micrometer lateral resolution. Our method has the potential for transient and spectroscopic vibration imaging of micromechanical systems at nano- and picosecond scale time resolution.

Optics,Applied Physics
Acoustic-Excitation Optical Coherence Vibrometer for Real-Time Microstructure Vibration Measurement and Modal Analysis

Ning Zhou,Shuncong Zhong,Jiewen Lin,Manting Luo,Walter Nsengiyumva,Zhike Peng,Yingjie Yu

DOI: https://doi.org/10.1109/tim.2020.2975453

IF: 5.6

2020-09-01

IEEE Transactions on Instrumentation and Measurement

Abstract:An acoustic-excitation optical coherence vibrometer (AE-OCV) is proposed for noncontact microstructure vibration measurement and modal analysis. The vibration dynamic parameters of the microstructure can be captured with a subnanometer displacement resolution by the proposed AE-OCV using spectral wavelength calibration algorithm and spectral center correction method. The natural frequency of the microstructure could also be obtained by the developed noncontact AE-OCV system using the swept-frequency acoustic excitation method. Furthermore, a home-made spectrometer based on a high-speed linear camera could provide the system with a frequency measurement range of 0–50 kHz. The developed AE-OCV has an excellent performance in microstructures vibration measurement and modal analysis, especially for high-frequency and nanoscale vibration measurements. It is of great significance to the design of the microelectromechanical system (MEMS), such as the noncontact dynamic measurement of cantilevered beams in atomic force microscopy.

engineering, electrical & electronic,instruments & instrumentation
High-speed, high-optical-efficiency laser scanning using a MEMS-based in-plane vibratory sub-wavelength diffraction grating

Guangya Zhou,Yu Du,Qingxin Zhang,Hanhua Feng,Fook Siong Chau

DOI: https://doi.org/10.1088/0960-1317/18/8/085013

2008-07-10

Journal of Micromechanics and Microengineering

Abstract:In this paper, we report the modeling, fabrication and characterization of a microelectromechanical systems (MEMS)-based sub-wavelength diffraction grating under in-plane motion for high-optical-efficiency high-speed laser-scanning applications. The scanner utilizes in-plane rotational vibration of a planar microstructure to change the orientation of the diffraction grating, hence causing a diffracted laser beam to scan with less dynamic wavefront deformation as compared with conventional scanning micromirrors. An optical efficiency of more than 75% is experimentally achieved with a simple gold-coated binary sub-wavelength grating. When operated in air and electrostatically driven by 45 V dc bias and 84 V peak-to-peak ac voltages, the 1 mm diameter grating is capable of scanning an optical scan angle of 13.7° with a 632.8 nm wavelength incident laser beam at a resonant frequency of 20.35 kHz. The measured optical resolution is around 310 pixels per unidirectional scan.

engineering, electrical & electronic,nanoscience & nanotechnology,instruments & instrumentation,physics, applied
Imaging nanomechanical vibrations and manipulating parametric mode coupling via scanning microwave microscopy

Hao Xu,Srisaran Venkatachalam,Toky-Harrison Rabenimanana,Christophe Boyaval,Sophie Eliet,Flavie Braud,Eddy Collin,Didier Theron,Xin Zhou

2024-06-29

Abstract:In this study, we present a novel platform based on scanning microwave microscopy for manipulating and detecting tiny vibrations of nanoelectromechanical resonators using a single metallic tip. The tip is placed on the top of a grounded silicon nitride membrane, acting as a movable top gate of the coupled resonator. We demonstrate its ability to map mechanical modes and investigate mechanical damping effects in a capacitive coupling scheme, based on its spatial resolution. We also manipulate the energy transfer coherently between the mode of the scanning tip and the underlying silicon nitride membrane, via parametric coupling. Typical features of optomechanics, such as anti-damping and electromechanically induced transparency, have been observed. Since the microwave optomechanical technology is fully compatible with quantum electronics and very low temperature conditions, it should provide a powerful tool for studying phonon tunnelling between two spatially separated vibrating elements, which could potentially be applied to quantum sensing.

Applied Physics,Instrumentation and Detectors
Velocity measurement of MEMS with temporal heterodyne microscopic speckle interferometry

Chenjia Gao,Zhan Gao,Yuhao Niu,Xu Wang,Jieming Zhao,Lin Deng

DOI: https://doi.org/10.1080/09500340.2021.1924886

IF: 1.3

2021-05-10

Journal of Modern Optics

Abstract:With the rapid development of micro electro mechanical systems (MEMS), the high-precision measurement technology applied to MEMS devices becomes increasingly important. Traditional micro scale measurement techniques such as scanning electron microscope (SEM), atomic force microscope (AFM), and scanning tunnelling microscope (STM) are widely used in measuring the surface topography and local deformation of MEMS. However, these scanning-based measurement technologies are difficult to achieve full-field and dynamic detection, and they are easy to cause damages to the measured object. In this paper, the microscopic speckle interferometry and heterodyne technology are combined to realize the measurement of constant velocity of MEMS. We presented the experimental principle of temporal heterodyne microscopic speckle interferometry, and measured the real-time motion of MEMS, which verified the feasibility of this method. The experimental results prove that our method has the advantages of real-time, full-field, good noise immunity and low-cost.

optics
A microcomb-empowered Fourier domain mode-locked LiDAR

Zhaoyu Cai,Zihao Wang,Ziqi Wei,Baoqi Shi,Wei Sun,Changxi Yang,Junqiu Liu,Chengying Bao

2024-08-02

Abstract:Light detection and ranging (LiDAR) has emerged as an indispensable tool in autonomous technology. Among its various techniques, frequency modulated continuous wave (FMCW) LiDAR stands out due to its capability to operate with ultralow return power, immunity to unwanted light, and simultaneous acquisition of distance and velocity. However, achieving a rapid update rate with sub-micron precision remains a challenge for FMCW LiDARs. Here, we present such a LiDAR with a sub-10 nm precision and a 24.6 kHz update rate by combining a broadband Fourier domain mode-locked (FDML) laser with a silicon nitride soliton microcomb. An ultrahigh frequency chirp rate up to 320 PHz/s is linearized by a 50 GHz microcomb to reach this performance. Our theoretical analysis also contributes to resolving the challenge of FMCW velocity measurements with nonlinear frequency sweeps and enables us to realize velocity measurement with an uncertainty below 0.4 mm/s. Our work shows how nanophotonic microcombs can unlock the potential of ultrafast frequency sweeping lasers for applications including LiDAR, optical coherence tomography and sensing.

Optics,Applied Physics
Common-path Heterodyne Self-Mixing Interferometry with Polarization and Frequency Multiplexing

Shaohui Zhang,Shulian Zhang,Yidong Tan,Liqun Sun

DOI: https://doi.org/10.1364/ol.41.004827

IF: 3.6

2016-01-01

Optics Letters

Abstract:A heterodyne Nd:YVO4 microchip laser self-mixing interferometry based on frequency and polarization multiplexing has been demonstrated. By using two orthogonally polarized lights to measure the measurement and reference target, the effect of the acousto-optic crystal thermal creep and air disturbance in interference light path is eliminated. In addition, the measurement error caused by the difference between two identical microchip lasers is compensated for by shifted frequency multiplexing technique. A rate equations model with multi-channel frequency-shifted feedback is established for interpreting the principle of the interferometry. Due to the ultrahigh sensitivity of the microchip laser, the target used in the experiment is a non-cooperative object which is different from the targets in conventional Michelson interferometers. Under typical room conditions, the short-term resolution is better than 2.5 nm, and the long-term zero drift is less than 60 nm within 7 h. The result shows that this self-mixing interferometry system is feasible and robust in the field of displacement measurement.
Precision vibration measurement using differential phase-modulated homodyne interferometry

Hui Liao,Jiandong Xie,Liping Yan,Benyong Chen,Yingtian Lou,Huan Chen,Gangxiang Guo

DOI: https://doi.org/10.1016/j.optlaseng.2023.107695

IF: 5.666

2023-10-01

Optics and Lasers in Engineering

Abstract:A novel precision vibration measurement using differential phase-modulated homodyne interferometry is presented. The orthogonal linearly polarized phase-modulated single frequency laser source is constructed by using a distributed feedback (DFB) fiber laser and a fiber-coupled electro-optic phase modulator (EOM). An auxiliary monitoring signal is used to differentially compensate the optical path drift and common-mode noise of the fiber. By pre-scanning the wavelength of DFB laser to introduce enough phase changes, ellipse fitting can be realized without moving the object more than half a wavelength. Therefore, the periodic nonlinearity of the phase generated carrier (PGC) demodulation is compensated. Experimental setup was built and the real-time signal processing was realized based on field programmable gate array (FPGA). The experiments of pulse vibration, sinusoidal vibration and comparison with commercial laser vibrometer were performed to verify the feasibility of the proposed method. The experimental results show that the average deviation of vibration amplitude is about 0.97 nm in the frequency range of 0.5 kHz to 10.0 kHz, which indicates that the proposed method has significant application for precision vibration measurement.

optics

Foot-and-mouth disease in white-tailed deer: clinical signs and transmission in the laboratory.

Femtometer-amplitude imaging of coherent super high frequency vibrations in micromechanical resonators

Stroboscopic Interferometer for Dynamic MEMS Characterization

Tunable-illumination for Laser Fourier Ptychographic Microscopy Based on a Background Noise-Reducing System

Micro-vibration measuring technology based on heterodyne interference

Nanoscale imaging of super-high-frequency microelectromechanical resonators with femtometer sensitivity

Integrated Measurement Of Micro Motions For Mems Dynamic Performance Analysis

Mirrorless MEMS imaging: a nonlinear vibrational approach utilizing aerosol-jetted PZT-actuated fiber MEMS scanner for microscale illumination

Single-particle vibrational spectroscopy using optical microresonators

Phase Sensitive Imaging of 10 GHz Vibrations in an AlN Microdisk Resonator

Real-time imaging of standing-wave patterns in microresonators

Single-particle Photoacoustic Vibrational Spectroscopy Using Optical Microresonators

Multi-frame interferometric imaging with a femtosecond stroboscopic pulse train for observing irreversible phenomena

Transient vibration imaging with time-resolved synthetic holographic confocal microscopy

Acoustic-Excitation Optical Coherence Vibrometer for Real-Time Microstructure Vibration Measurement and Modal Analysis

High-speed, high-optical-efficiency laser scanning using a MEMS-based in-plane vibratory sub-wavelength diffraction grating

Imaging nanomechanical vibrations and manipulating parametric mode coupling via scanning microwave microscopy

Velocity measurement of MEMS with temporal heterodyne microscopic speckle interferometry

A microcomb-empowered Fourier domain mode-locked LiDAR

Common-path Heterodyne Self-Mixing Interferometry with Polarization and Frequency Multiplexing

Precision vibration measurement using differential phase-modulated homodyne interferometry