Abstract:A low‐carbon (0.23 wt%) carbide‐free bainitic steel is successfully developed with a total alloying addition of 4.9 wt%, which is relatively lower than alloying additions reported in similar category of steels. The present findings indicate that the currently designed low‐alloy steel composition is amenable to generation of nearly carbide‐free bainitic microstructure in large‐sized components under normal cooling conditions. Microstructures of steel after a,b) water quenching, c,d) air cooling, and e,f) furnace cooling, where bainite is obtained in both air and furnace cooled conditions. Bainitic microstructures in high‐strength steels are obtained either by continuous cooling or isothermal holding. Both scenarios necessitate faster cooling to keep the parent austenite phase untransformed till the bainite‐start temperature. The present study reports the development of bainitic microstructure in a low‐carbon steel with minimal alloying additions, under continuous cooling at very slow rates, similar to furnace cooling. For understanding the related transformation pathways, samples from the forged‐steel ingot are austenitized and cooled at different rates, viz. water quenching, air cooling, and furnace cooling. Microstructural characterization reveals development of acicular microstructures in all samples including the forged one, with gross absence of carbides. X‐ray diffraction confirms the ferritic nature of acicular plates and also indicated retained austenite present in some samples, the content of which could be correlated to the extent of bainitic transformation. Thermodynamic calculations together with microstructural observations (e.g., ferrite plate size) and hardness data established the development of fully martensitic microstructure on water quenching, while that of a mixed microstructure comprising predominantly of bainite in the forged, air cooled, and furnace‐cooled condition. The aforementioned findings could have wider implications in developing fully bainitic microstructures in large components, where uniform rapid cooling is not practically feasible.

Controlling the Thermal Stability of a Bainitic Structure by Alloy Design and Isothermal Heat Treatment

Strain-induced Refinement and Thermal Stability of a Nanocrystalline Steel Produced by Surface Mechanical Attritiontreatment

Novel Method for Refinement of Retained Austenite in Micro/nano-Structured Bainitic Steels

Thermal stability of retained austenite in bainitic steel: an in situ study

Microstructures and Mechanical Properties of a Modified High-C–cr Bearing Steel with Nano-Scaled Bainite

Mechanism of Formation and Characteristics of Microstructure of Novel Nanobainitic Steel

Microstructure and Properties of a Low Carbon Bainitic Steel Produced by Conventional and Inverted Two-Step Austempering Processes

Low-temperature bainite in low-carbon steel

In-situ Observation of Phase Transformation During Heat Treatment Process of High-Carbon Bainitic Bearing Steel

Effect of Tempering Temperature on Microstructure and Mechanical Properties of Nanostructured Bainitic Steel

Multi-Step Isothermal Bainitic Transformation in Medium-Carbon Steel

Carbide-Free Bainite in Medium Carbon Steel

Effect of the cooling rate in the medium temperature zone on the phase transformation and microstructure of carbide-free bainitic steel

Experimental and theoretical analysis of multiphase microstructure in a newly designed MnSiCrC quenched and partitioned steel to promote bainitic transformation: The significant impact on mechanical properties

Ultra-Fine Bainite in Medium-Carbon High-Silicon Bainitic Steel

Three-dimensional morphology and crystallographic characteristics of the low-temperature bainitic microstructure in high-carbon steel

Formation of Bainite in a Low‐Carbon Steel at Slow Cooling Rate – Experimental Observations and Thermodynamic Validation

Tuning Bainitic Microstructures by Complex Thermo-mechanical Treatments under Constant Stress

Kinetics of austenite growth and bainite transformation during reheating and cooling treatments of high strength microalloyed steel produced by sub-rapid solidification

Stability of Retained Austenite and Work Hardening Behavior in Ultra-Fine Medium Carbon Bainitic Steel