Abstract:The volume fraction and stability of retained austenite play an important role in the performance of low carbon steels, while the C and Mn elements have a stabilizing effect on the thermal stability and mechanical stability of retained austenite. Therefore, the C and Mn elementals partitioning was promoted by intercritical annealing. As a result, the mechanical properties of the low carbon steels are improved. The microstructure of quenching and partitioning bainitic steels and retained austenite characteristics were studied by means of SEM, TEM and XRD. The partitioning and content of C and Mn elements in retained austenite at different locations were characterized by EPMA, EBSD and nanoindentation. The effect of C and Mn elements on the stability of retained austenite at different locations and phase change law of retained austenite were investigated by combining the tensile stress-strain curves under the treatment of intercritical annealing (partial austenitizing)-quenching and partitioning in the bainitic region process (IQ&PB). In the process of tensile deformation, the transformation induced plasticity (TRIP) effect occurs, the volume of retained austenite decreases, the transformation takes place preferentially in the ferrite grain boundary, and finally occurs between the bainite laths. C and Mn elements have a stabilizing effect on the retained austenite, which make retained austenite is not prone to phase change. The stress at the tensile fracture is concentrated, and the retained austenite is completely transformed into martensite. The volume fraction of retained austenite is 3.12% and 5.03% at 2 mm and 4 mm distances away from the fracture. Film-like retained austenite is more stable than blocky retained austenite, and the retained austenite of the < 111 >(gamma) crystal orientation is unstable and easily transforms into martensite.

Thermal stability of retained austenite in bainitic steel: an in situ study

Stability of retained austenite in high carbon steel – Effect of post-tempering heat treatment

Microstructure and property evolution during tempering of a medium carbon bainitic steel

Kinetics of Martensite/Austenite Decomposition during Tempering of Ultrafine Nano-Bainitic Steels

Controlling the Thermal Stability of a Bainitic Structure by Alloy Design and Isothermal Heat Treatment

C and Mn Elements Characterization and Stability of Retained Austenite in Different Locations of Quenching and Partitioning Bainite Steels

In-Situ High Temperature X-Ray Studies on Bainitic Transformation of Austempered Silicon Alloyed Steels

Effect of prior martensite formation on the bainite transformation kinetics in high-strength 3% Mn multiphase steel

Morphology of Retained Austenite and Its Effects on the Mechanical Properties of High Silicon Cast Steel

Austenite Formation and Cementite Dissolution During Intercritical Annealing of a Medium-Manganese Steel from a Martensitic Condition

Microstructure and Properties of a Low Carbon Bainitic Steel Produced by Conventional and Inverted Two-Step Austempering Processes

Austenite Thermal Stabilization Through the Concentration of Manganese and Carbon in the 0.2c–5mn Steel

A thermodynamic study of inverse bainitic transformation

Revealing the Role of Dislocations on the Stability of Retained Austenite in a Tempered Bainite

Effect of isothermal quenching on the amount and stability of residual austenite and on the properties of structural steels

Tempering Effects on the Stability of Retained Austenite and Mechanical Properties in a Medium Manganese Steel

Austenitizing Temperature and Cooling Rate Effects on the Martensitic Transformation in a Microalloyed-Steel

Effects of Retained Austenite upon Softening during Low-temperature Tempering in Martensitic Carbon Steels

Kinetics of austenite growth and bainite transformation during reheating and cooling treatments of high strength microalloyed steel produced by sub-rapid solidification

Role of cementite and retained austenite on austenite reversion from martensite and bainite in Fe-2Mn-1.5Si-0.3C alloy