A forward-trajectory global semi-Lagrangian transport scheme

R. Nair,J. S. Scroggs,F. Semazzi

DOI: https://doi.org/10.1016/S0021-9991(03)00274-2

2003-09-01

Abstract:

What problem does this paper attempt to address?

Sludge minimization in municipal wastewater treatment by polyhydroxyalkanoate (PHA) production

Francesco Valentino,Fernando Morgan-Sagastume,Serena Fraraccio,Giovanna Corsi,Giulio Zanaroli,Alan Werker,Mauro Majone

DOI: https://doi.org/10.1007/s11356-014-3268-y

IF: 5.8

2014-07-05

Environmental Science and Pollution Research

Abstract:An innovative approach has been recently proposed in order to link polyhydroxyalkanoates (PHA) production with sludge minimization in municipal wastewater treatment, where (1) a sequencing batch reactor (SBR) is used for the simultaneous municipal wastewater treatment and the selection/enrichment of biomass with storage ability and (2) the acidogenic fermentation of the primary sludge is used to produce a stream rich in volatile fatty acids (VFAs) as the carbon source for the following PHA accumulation stage. The reliability of the proposed process has been evaluated at lab scale by using substrate synthetic mixtures for both stages, simulating a low-strength municipal wastewater and the effluent from primary sludge fermentation, respectively. Six SBR runs were performed under the same operating conditions, each time starting from a new activated sludge inoculum. In every SBR run, despite the low VFA content (10 % chemical oxygen demand, COD basis) of the substrate synthetic mixture, a stable feast–famine regime was established, ensuring the necessary selection/enrichment of the sludge and soluble COD removal to 89 %. A good process reproducibility was observed, as also confirmed by denaturing gradient gel electrophoresis (DGGE) analysis of the microbial community, which showed that a high similarity after SBR steady-state had been reached. The main variation factors of the storage properties among different runs were uncontrolled changes of settling properties which in turn caused variations of both sludge retention time and specific organic loading rate. In the following accumulation batch tests, the selected/enriched consortium was able to accumulate PHA with good rate (63 mg CODPHA g CODXa−1 h−1) and yield (0.23 CODPHA CODΔS−1) in spite that the feeding solution was different from the acclimation one. Even though the PHA production performance still requires optimization, the proposed process has a good potential especially if coupled to minimization of both primary sludge (by its use as the VFA source for the PHA accumulation, via previous fermentation) and excess secondary sludge (by its use as the biomass source for the PHA accumulation).

environmental sciences
PHA and EPS production from industrial wastewater by conventional activated sludge, membrane bioreactor and aerobic granular sludge technologies: A comprehensive comparison

Francesco Traina,Marco Capodici,Michele Torregrossa,Gaspare Viviani,Santo Fabio Corsino

DOI: https://doi.org/10.1016/j.chemosphere.2024.141768

IF: 8.8

2024-05-01

Chemosphere

Abstract:The present study has focused on the mainstream integration of polyhydroxyalkanoate (PHA) production with industrial wastewater treatment by exploiting three different technologies all operating in sequencing batch reactors (SBR): conventional activated sludge (AS-SBR), membrane bioreactor (AS-MBR) and aerobic granular sludge (AGS). A full aerobic feast/famine strategy was adopted to obtain enrichment of biomass with PHA-storing bacteria. All the systems were operated at different organic loading (OLR) rate equal to 1-2-3 kgCOD/m<sup>3</sup>∙d in three respective experimental periods. The AS-MBR showed the better and stable carbon removal performance, whereas the effluent quality of the AS-SBR and AGS deteriorated at high OLR. Biomass enrichment with PHA-storing bacteria was successfully obtained in all the systems. The AS-MBR improved the PHA productivity with increasing OLR (max 35% w/w), whereas the AS-SBR reduced the PHA content (max 20% w/w) above an OLR threshold of 2 kgCOD/m<sup>3</sup>∙d. In contrast, in the AGS the increase of OLR resulted in a significant decrease in PHA productivity (max 14% w/w) and a concomitant increase of extracellular polymers (EPS) production (max 75% w/w). Results demonstrated that organic carbon was mainly driven towards the intracellular storage pathway in the AS-SBR (max yield 51%) and MBR (max yield 61%), whereas additional stressors in AGS (e.g., hydraulic selection pressure, shear forces) induced bacteria to channel the COD into extracellular storage compounds (max yield 50%) necessary to maintain the granule's structure. The results of the present study indicated that full-aerobic feast/famine strategy was more suitable for flocculent sludge-based technologies, although biofilm-like systems could open new scenarios for other biopolymers recovery (e.g., EPS). Moreover, the AS-MBR resulted the most suitable technology for the integration of PHA production in a mainstream industrial wastewater treatment plant, considering the greater process stability and the potential reclamation of the treated wastewater.

environmental sciences
Polyhydroxyalkanoate Production from Food Waste Coupled with Aerobic Nitrate Reduction

Menghan Wu,Xinning Liu,Huilei Xiong,Weiming Tu,Xiaoqiang Gong,Peng Yu,Yina Zou,Hui Wang

DOI: https://doi.org/10.1021/acssuschemeng.1c04726

2021-11-10

Abstract:Polyhydroxyalkanoate (PHA) production from wastes by mixed microbial cultures has been developed into an integrated process to couple with nitrate removal due to its economic and environmental benefits. However, the anoxic conditions for denitrification result in low productivity of PHA production due to the limited energy supply. In this work, the fully aerobic feeding regime uncoupling carbon and nitrogen supply was applied to enhance the culture enrichment and productivity while being accompanied by nitrate removal. The enriched cultures showed a nitrate assimilation rate of 2.35 ± 1.10 mg of NO3 ––N per gram of active biomass (X a) per hour; meanwhile, the specific growth rate (μ X a , 0.019 ± 0.002 h–1) and biomass yield on PHA (Y X a/PHA, 0.68 ± 0.15 g X a/g PHA) were higher than those of a classic anoxic process (μ X a , 0.011 ± 0.001 h–1 and Y X a/PHA, 0.38 ± 0.09 g X a/g PHA). Furthermore, ammonia and oxygen were confirmed to have significant impacts on regulating nitrate utilization by directing nitrate flow to assimilatory nitrate use, aerobic denitrification, or anoxic denitrification. Metagenome analysis revealed that the overall function was mostly undertaken by Thauera aminoaromatica, and a nitrate metabolic model driven by PHAs was proposed. In summary, these findings widened application scenarios for PHA production coupled with nitrate removal.

chemistry, multidisciplinary,engineering, chemical,green & sustainable science & technology
Coupling of Polyhydroxyalkanoate Production with Volatile Fatty Acid from Food Wastes and Excess Sludge

Mingmei Zhang,Haiyun Wu,Hong Chen

DOI: https://doi.org/10.1016/j.psep.2012.12.002

IF: 7.8

2012-01-01

Process Safety and Environmental Protection

Abstract:In this paper, the synthesis of polyhydroxyalkanoates (PHAs) by activated sludge with aerobic dynamic feeding process was conducted in a sequencing batch reactor by using food wastes and excess sludge fermentation liquid as the carbon source. The volatile fatty acids (VFAs) in the fermentation liquid were divided into even-numbered (acetic and butyric acid) and odd-numbered (propionic and valeric acid). The experiments conducted by central-composite design (CCD) showed that the pH could significantly affect the ratio of even-numbered to odd-numbered VFAs. Statistical analysis indicated a positive correlation (R2=0.97, P<0.05) between the consumption of even-numbered VFAs and the synthesized of PHB, while the consumption of odd-numbered VFAs were correlated with the synthesized PHV. By controlling the ratio of even-numbered to odd-numbered VFAs, the contents of PHV in the PHAs could be controlled within the range of 22–30%. When fermentative VFAs were used as the substrate for the synthesis of PHAs, the microbial synthesis of PHA and biomass was higher than that mixture of analytically pure acids was used. These results are of vital significance for the comprehensive utilization of solid wastes.
A contribution to resource recovery from wastewater. Anaerobic processes for organic matter and nitrogen treatment

Núria Basset Olivé

2015-10-16

Abstract:Organic matter and nutrients present in urban and industrial wastewater should be removed or valorised to reduce its impact on the environment. Conventional wastewater treatments are focused on the removal of these pollution sources at the minimum cost. The idea of resource recovery from wastewater is changing the concept of the conventional wastewater treatment plants that tend to incorporate little by little processes as anaerobic digestion, MBR, biofilm, granulation, etc. However, their application to obtain reusable by-products from wastes should be cost effective. Winery wastewater is an effluent with a highly biodegradable organic load, worth considering for biogas production, and low nutrient content. A sidestream anaerobic membrane bioreactor (AnMBR) was started up and operated under organic load oscillations. The stable operation was assured by keeping a ratio between intermediate alkalinity and total alkalinity (IA/TA) below 0.3 achieving a 96.7±2.7% COD removal efficiency. The biogas production varied according with the OLR that was on average 0.50±0.17 m(3)(biogas)/m(-3)(digester)/d(-1) with an 87.1±3.0% of methane. The external membrane module reached a flux of 20.2 ± 8.5 LMH at a crossflow velocity of 0.64 m s-1. The crossflow velocity helped to remove the cake layer attached on the membrane that was the main contribution (>80%) to flux decline. The energy demand of the AnMBR was calculated considering the net energy production of a combined heat and power (CHP) unit. It was concluded that only when influent COD was over 3.25 gCOD 1:1- the energy balance was positive. Considering the upscaling of the AnMBR of the present study, the submerged membrane configuration would be a more feasible option due to its lower operational costs, especially in winter season. Simulating the conditions of winter season, winery wastewater was treated in the AnMBR at low temperatures of 25°C and 15°C. Since the organic load of winery wastewater in winter is much lower than in summer (vintage season), the average OLR applied was 0.32 and 0.29 kgCOD m(-3)(digester)/d(-1) the average COD removal reached was 80% and 71% at 25°C and 15°C., respectively. Moreover, higher degree of fouling was observed despite the amount of suspended solids was lower, so frequent cleanings were necessary. The effluent of anaerobic digestion often requires a post-treatment to remove nutrients, especially nitrogen. Compared with conventional biological nitrogen removal, nitritation/denitritation (N/DN) via nitrite represent a 25% less aeration and 40% less external carbon source. In order to reach higher flexibility and reducing space requirements, N/DN can be carried out in a sequencing batch reactor (SBR). Under feast and famine conditions applied in the SBR, storage compounds can be served as internal carbon sources for post-anoxic denitrification. A novel scheme was developed for the treatment of municipal wastewater; consisting in an UASB reactor followed by a short cut sequencing batch reactor (scSBR) in the main water line. Nitritation/denitritation was integrated with the selection of polyhydroxyalkanoate (PHA) storing biomass. Biowaste fermented liquid was applied as carbon source in the feast regime. The average nitrogen removal was 83%. After achieving an acceptable ammonia removal of 93%, there was enough available PHA for the subsequent denitritation, reaching a maximum nitrite removal of 98%. The maximum PHA content was 10.6% (gPHA gTSS-1) after 10 h of accumulation when biowaste fermented liquid (C/N/P= 100/4.5/0.42) was applied. Nitrogen removal limits could be successfully met while PHA-storing biomass was selected. Although higher PHA yields can be achieved under complete aerobic conditions, this novel scheme presents an added value due to the integration of the PHA production in the nitritation/denitritation process.

Environmental Science
Polyhydroxyalkanoates (PHA) Production from Fermented Thermal-Hydrolyzed Sludge by PHA-storing Denitrifiers Integrating PHA Accumulation with Nitrate Removal.

Weiming Tu,Dandan Zhang,Hui Wang,Ziyu Lin

DOI: https://doi.org/10.1016/j.biortech.2019.121895

IF: 11.4

2019-01-01

Bioresource Technology

Abstract:Polyhydroxyalkanoates (PHA) production from fermented thermal-hydrolyzed sludge was conducted by mixed microbial cultures (MMCs) in the study. An MMC enriched in the species Brachymonas denitrificans (60.18%) was selected under an aerobic feast/famine regime, which is capable of denitrification and accumulating PHA. To take advantage of the PHA-storing denitrifiers, an aerobic-feast/anoxic-famine regime was applied to integrate culture selection with denitrification. The results showed that cultures enriched under the regime exhibited a PHA storage capacity with PHA yield on VFA of 0.47 gCOD/gCOD and well denitrification performance achieving nitrate removal of 98%. Moreover, the aerobic-feast/anoxic-famine regime could originate a comparable maximum PHA content to the complete aerobic feast/famine regime (49.7 wt% versus. 47.1 wt%, respectively), yet reduce aeration energy input by 79% in the culture selection process. Finally, this study investigated the accumulation of nitrite and nitrous oxide during PHA based denitrification and the feasibility of integrating the process with wastewater treatment.
Use of skinfold thickness for estimation of body fat.

J. N. Berry

The Indian Journal of Medical Research

Abstract:
Modelling Mixed Microbial Culture Polyhydroxyalkanoate Accumulation Bioprocess towards Novel Methods for Polymer Production Using Dilute Volatile Fatty Acid Rich Feedstocks

Alan Werker,Laura Lorini,Marianna Villano,Francesco Valentino,Mauro Majone

DOI: https://doi.org/10.3390/bioengineering9030125

IF: 5.046

2022-03-21

Bioengineering

Abstract:Volatile fatty acid (VFA) rich streams from fermentation of organic residuals and wastewater are suitable feedstocks for mixed microbial culture (MMC) Polyhydroxyalkanoate (PHA) production. However, many such streams have low total VFA concentration (1–10 gCOD/L). PHA accumulation requires a flow-through bioprocess if the VFAs are not concentrated. A flow through bioprocess must balance goals of productivity (highest possible influent flow rates) with goals of substrate utilization efficiency (lowest possible effluent VFA concentration). Towards these goals, dynamics of upshift and downshift respiration kinetics for laboratory and pilot scale MMCs were evaluated. Monod kinetics described a hysteresis between the upshift and downshift responses. Substrate concentrations necessary to stimulate a given substrate uptake rate were significantly higher than the concentrations necessary to sustain the attained substrate uptake rate. A benefit of this hysteresis was explored in Monte Carlo based PHA accumulation bioprocess numerical simulations. Simulations illustrated for a potential to establish continuous flow-through PHA production bioprocesses even at a low (1 gCOD/L) influent total VFA concentration. Process biomass recirculation into an engineered higher substrate concentration mixing zone, due to the constant influent substrate flow, enabled to drive the process to maximal possible PHA production rates without sacrificing substrate utilization efficiency.
Consistent production of high quality PHA using activated sludge harvested from full scale municipal wastewater treatment - PHARIO

Alan Werker,Simon Bengtsson,Leon Korving,Markus Hjort,Simon Anterrieu,Tomas Alexandersson,Peter Johansson,Anton Karlsson,Lamija Karabegovic,Per Magnusson,Fernando Morgan-Sagastume,Luc Sijstermans,Martin Tietema,Cindy Visser,Etteke Wypkema,Yede van der Kooij,Alexandra Deeke,Cora Uijterlinde

DOI: https://doi.org/10.2166/wst.2018.502

Abstract:Production of polyhydroxyalkanoate (PHA) biopolymers by mixed microbial cultures concurrent to wastewater treatment is a valorization route for residual organic material. This development has been at pilot scale since 2011 using industrial and municipal organic residuals. Previous experience was the basis for a PHA production demonstration project: PHARIO. PHARIO was centred on processing surplus activated sludge biomass from the Bath full-scale municipal wastewater treatment plant in the Netherlands to produce PHA. Full-scale surplus activated sludge was fed to a pilot facility to produce PHA rich biomass using fermented volatile fatty acid (VFA) rich liquors from industry or primary sludge sources. A PHA rich biomass with on average 0.41 gPHA/gVSS was obtained with reproducible thermal properties and high thermal stability. A routine kilogram scale production was established over 10 months and the polymer material properties and market potential were evaluated. Surplus full-scale activated sludge, over four seasons of operations, was a reliable raw material to consistently and predictably produce commercial quality grades of PHA. Polymer type and properties were systematic functions of the mean co-polymer content. The mean co-polymer content was predictably determined by the fermented feedstock composition. PHARIO polymers were estimated to have a significantly lower environmental impact compared to currently available (bio)plastics.
Optimization of an enriched mixed culture to increase PHA accumulation using industrial saline complex wastewater as a substrate

Lucía Argiz,Andrea Fra-Vázquez,Ángeles Val Del Río,Anuska Mosquera-Corral

DOI: https://doi.org/10.1016/j.chemosphere.2020.125873

IF: 8.8

Chemosphere

Abstract:Polyhydroxyalkanoates (PHA) appear as good candidates to substitute conventional petroleum-based plastics since they have similar properties but with the advantage of being biodegradable. Wastewater streams with high organic content are feasible substrates for PHA production resulting in an opportunity for waste recovery. One of the main challenges is the optimization of the selection of microorganisms with high PHA storage capacity. This microbial selection is performed in sequencing batch reactors (SBR) operated under an aerobic feast/famine (F/F) regime. In the present study, a settling stage was added at the end of the feast phase of the enrichment cycle of a SBR fed with pre-acidified cooked mussel processing wastewater (containing up to 12 g NaCl/L). Settling and subsequent supernatant discharge favoured the wash-out of non-accumulating microorganisms as well as the removal of substances that enhanced their undesired development (proteins and carbohydrates). Microbial analysis performed by fluorescence in situ hybridization (FISH) technique showed shifts in the microbial community; the presence of genus Paracoccus increased whereas genera Comamonas decreased. Moreover, the process efficiency was improved with the increase of the PHA production yield (YPHA) and the maximum PHA storage capacity (max. PHA) from 0.48 to 0.72 CmmolPHA/CmmolVFA and from 40 to 60 wt%, respectively. The polymer composition also changed, its HB:HV ratio varied from 83:17 to 70:30. Results obtained in the present study showed that settling after the feast phase promoted the removal of carbon sources that did not contribute to PHA production and the washout of non-storing bacteria, which favoured the culture enrichment.
Doubling time and annual doubling rate of human prostatic cancer.

F. Haddad,L. Haddad,E. E. Griffin,R. Haddad,Z. Haddad

DOI: https://doi.org/10.1016/0090-4295(87)90594-2

IF: 2.633

Urology

Abstract:
Towards scaling-up implementation of polyhydroxyalkanoate (PHA) production from activated sludge: Progress and challenges

Zixin Zhang,Yufen Wang,Xiaomin Wang,Yaobin Zhang,Tingting Zhu,Lai Peng,Yifeng Xu,Xueming Chen,Dongbo Wang,Bing-Jie Ni,Yiwen Liu

DOI: https://doi.org/10.1016/j.jclepro.2024.141542

IF: 11.1

2024-03-09

Journal of Cleaner Production

Abstract:Polyhydroxyalkanoate (PHA) is a biodegradable biopolymer synthesized from renewable resources, providing sustainable and eco-friendly plastics. The utilization of activated sludge for PHA production has gained prominence due to its cost-effectiveness and abundant availability. Upscaling PHA production from activated sludge can contribute to waste management and resource recovery simultaneously, thereby reducing the dependence on petroleum-based plastics. This review critically examines the progress and challenges in this field, while offering valuable insights into strategies for enhancing productivity, improving product quality, and reducing costs. The analysis primarily focuses on identifying key factors influencing each stage of the three-stage process aimed at increasing productivity. Noteworthy strategies proposed include optimizing the enrichment process and feast/famine ratio. For high-quality PHA, the emphasis is on oriented acid production, and the selection of appropriate extraction methods is crucial. The review also addresses cost reduction, discussing the simplification of the process through the two-stage process, and integration of nitrogen removal with PHA production. Future research directions are outlined, highlighting the optimization of PHA quality, scalability of production, development of efficient extraction methods, assessment of environmental impacts, and alignment with policy measures. Conclusively, activated sludge-based PHA production shows great promise and necessitates further research and development for industrialization.

environmental sciences,green & sustainable science & technology,engineering, environmental
Polyhydroxyalkanoates production from a waste-derived feedstock driven by the reactor operating conditions: The role of biomass microbiome and its reactivation capacity

Eliana C. Guarda,Catarina L. Amorim,Gabriele Pasculli,Paula M.L. Castro,Claudia F. Galinha,Anouk F. Duque,Maria A.M. Reis

DOI: https://doi.org/10.1016/j.jclepro.2024.141810

IF: 11.1

2024-04-08

Journal of Cleaner Production

Abstract:In the last years, the production of plastics at large-scale has been an issue of great concern due to their environmental and health impacts. Biobased and biodegradable plastics, such as polyhydroxyalkanoates (PHA), have emerged as a possible more ecological and sustainable alternative to those conventional plastics. PHA can be produced by mixed microbial cultures (MMC) from waste-based feedstocks. This work aimed to maximize the PHA production from fermented brewer's spent grain by selecting an efficient PHA-accumulating MMC, applying different organic loading rates (OLR, 45 or 60 Cmmol FP /(L.d)) and sludge retention times (SRT, 4 or 2 days). Additionally, the biomass reactivation capacity after storage was evaluated. The global PHA productivity depends on the operating conditions, achieving its maximum (3.55 ± 0.8 g PHA /(L.d)) at the highest OLR and SRT tested. After storage, the global PHA productivity was similar to the one achieved before the starvation period. Depending on the operating conditions, the microbiome has its own bacterial composition signature containing various PHA-producers genera (e.g., Acidovorax , Amaricoccus , Brevundimonas , Leucobacter , Leadbetterella and Thauera ) that persisted over time, albeit at different relative abundancies. A comprehensive overview of PHA production with data on system performance and microbiome is presented, which thereby can further contribute to the upscale of such valorisation processes.

environmental sciences,green & sustainable science & technology,engineering, environmental
Process optimization for efficient biomediated PHA production from animal-based waste streams

Michaela Titz,Karl-Heinz Kettl,Khurram Shahzad,Martin Koller,Hans Schnitzer,Michael Narodoslawsky

DOI: https://doi.org/10.1007/s10098-012-0464-7

IF: 4.3

2012-02-18

Clean Technologies and Environmental Policy

Abstract:Conventional polymers are made of crude oil components through chemical polymerization. The aim of the project ANIMPOL is to produce biopolymers by converting lipids into polyhydroxyalkanoates (PHA) in a novel process scheme to reduce dependence on crude oil and decrease greenhouse gas emissions. PHA constitutes a group of biobased and biodegradable polyesters that may substitute fossil-based polymers in a wide range of applications. Waste streams from slaughtering cattle are used as substrate material. Lipids from rendering are used in this process scheme for biodiesel production. Slaughtering waste streams may also be hydrolyzed to achieve higher lipid yield. Biodiesel then is separated into a high- and low-quality fraction. High-quality biodiesel meets requirements for sale as fuel and low quality is used for PHA production as carbon source. Selected offal material is used for acid hydrolysis and serves as a source of organic nitrogen as well as carbon source for PHA-free biomass with high production rate in fermentation process. Nitrogen is a limiting factor to control PHA production during the fermentation process. It is available for bacterial growth from hydrolyzed waste streams as well as added separately as NH4OH solution. Selected microbial strains are used to produce PHA from this substrate. The focus of the paper is about an overview of the whole process with the main focus on hydrolysis, to look for the possibility of using offal hydrolysis as an organic nitrogen substitute. The process design is optimized by minimizing waste streams and energy losses through cleaner production. Ecological evaluation of the process design will be done through footprint calculation according to Sustainable Process Index methodology.

environmental sciences,green & sustainable science & technology,engineering, environmental
Effect of culture history and carbon sources on polyhydroxyalkanoates production in activated sludge systems

Bengisu Ciftcioglu-Gozuacik,Ilke Pala-Ozkok,Emine Ubay-Cokgor

DOI: https://doi.org/10.1080/09593330.2024.2406987

IF: 3.475

2024-09-28

Environmental Technology

Abstract:Polyhydroxyalkanoates (PHAs) are important and completely biodegradable alternatives to regular plastics, and they can be produced by activated sludge systems during wastewater treatment. Wastewaters with high organic content are being used for PHA production, which is an important resource recovery option. In this context, the effect of sludge retention time and different carbon sources, such as acetate, peptone-mixture and industrial wastewater (containing acetic acid (AA), lactic acid (LA) and propionic acid (PA)), on PHA storage was investigated. Oxygen utilisation rate (OUR) profiles were generated in respirometric tests and were evaluated by activated sludge modelling. Results showed that high storage (AA: 70%; LA: 49%; PA: 60% and industrial wastewater: 52%) was achievable in the feast phase even when the biomass was fed with a high organic acid content substrate to which it is not acclimated.

environmental sciences
Modeling the partial nitrification in sequencing batch reactor for biomass adapted to high ammonia concentrations

V. Pambrun,E. Paul,M. Spérandio

DOI: https://doi.org/10.1002/bit.21008

IF: 3.8

2006-01-01

Biotechnology and Bioengineering

Abstract:Partial nitrification has proven to be an economic way for treatment of industrial N-rich effluent, reducing oxygen and external COD requirements during nitrification/denitrification process. One of the key issues of this system is the intermediate nitrite accumulation stability. This work presents a control strategy and a modeling tool for maintaining nitrite build-up. Partial nitrification process has been carried out in a sequencing batch reactor at 30 degrees C, maintaining strong changing ammonia concentration in the reactor (sequencing feed). Stable nitrite accumulation has been obtained with the help of an on-line oxygen uptake rate (OUR)-based control system, with removal rate of 2 kg NH4 (+)-N x m(-3)/day and 90%-95% of conversion of ammonium into nitrite. A mathematical model, identified through the occurring biological reactions, is proposed to optimize the process (preventing nitrate production). Most of the kinetic parameters have been estimated from specific respirometric tests on biomass and validated on pilot-scale experiments of one-cycle duration. Comparison of dynamic data at different pH confirms that NH3 and NO2- should be considered as the true substrate of nitritation and nitratation, respectively. The proposed model represents major features: the inhibition of ammonia-oxidizing bacteria by its substrate (NH3) and product (HNO2), the inhibition of nitrite-oxidizing bacteria by free ammonia (NH3), the INFluence of pH. It appears that the model correctly describes the short-term dynamics of nitrogenous compounds in SBR, when both ammonia oxidizers and nitrite oxidizers are present and active in the reactor. The model proposed represents a useful tool for process design and optimization.

biotechnology & applied microbiology
Improving carbon management through maximizing hydrolysis and fermentation at water resource recovery facilities

Francesca Cecconi,Leah Pifer,Fabrizio Sabba,Leon Downing

DOI: https://doi.org/10.3389/fenve.2024.1378621

2024-05-23

Frontiers in Environmental Engineering

Abstract:Wastewater treatment plants are transitioning from a sole focus on treatment objectives to integrated resource recovery and upcycling. Effective carbon management is critical for upcycling within a water resource recovery facility (WRRF) to produce energy or other usable products, which involves carbon diversion at primary treatment and waste activated sludge (WAS) from biological treatment processes. Many WRRFs are also driven to meet stringent effluent nutrient discharge targets while minimizing energy usage and chemical addition. Nutrient removal systems still rely on biodegradable organic carbon to support denitrification and enhanced biological phosphorus removal (EBPR). Biological nutrient removal not only requires sufficient organic substrate, but also the right type of bioavailable carbon for optimal utilization. The main objective of this pilot fermentation testing was to evaluate the most effective utilization of the range of organic-carbon rich feedstocks within a WRRF. Preliminary results suggest that a 50–50 blend of primary sludge (PS) and return activated sludge (RAS) fermentation leads to highest volatile fatty acid (VFA) yield. PS fermentation resulted in the minimum nutrients release per unit of volatile suspended solids (VSS), which makes it a best suited for biological nutrients removal WRRFs with stringent nitrogen (N) and phosphorus (P) limits. The volatile fatty acids fractions produced from different combinations of RAS and PS can impact the most suitable end use for each sludge type fermentation. PS resulted into higher levels of propionate, which are ideal for selecting phosphate accumulating organisms (PAO) over glycogen-accumulating organisms (GAO). On the other hand, for denitrification, acetate is the preferred substrate, which was most abundant with RAS only fermentation. Our research outcomes will be of value to utilities aiming to integrate the stringent effluent nutrient (N and P) discharge targets with energy and resource recovery.
Learning Causal Polytrees

J. Huete,L. M. D. Campos

DOI: https://doi.org/10.1007/BFb0028199

1993-11-08

Abstract:
Bioplastic polyhydroxyalkanoate conversion in waste activated sludge

Rui Guo,Xiaotong Cen,Bing-Jie Ni,Min Zheng

DOI: https://doi.org/10.1016/j.jenvman.2024.122866

Abstract:Polyhydroxyalkanoates (PHA) have been proposed as a promising solution for plastic pollution due to their biodegradability and diverse applications. To promote PHA as a competitive commercial product, an attractive alternative is to produce and recover PHA in the use of mixed cultures such as waste activated sludge from wastewater treatment plants. PHA can accumulate in sludge with a potential range of 40%-65% g PHA/g VSS. However, wider challenges with PHA production efficiency, stability, and economic viability still persist for PHA application. This work provides an overview of the current understanding and status of PHA bioconversion in waste sludge with particular attention given to metabolic pathways, operation modes, factors affecting the process, and applications. Challenges and future prospectives for PHA bioconversion in sludge are discussed.
Insights on biological phosphorus removal with partial nitrification in single sludge system via sidestream free ammonia and free nitrous acid dosing

Xuanyu Lu,Adrian Oehmen,Jing Zhao,Haoran Duan,Zhiguo Yuan,Liu Ye

DOI: https://doi.org/10.1016/j.scitotenv.2023.165174

2023-07-04

Abstract:The sidestream sludge treatment by free ammonium (FA)/free nitrous acid (FNA) dosing was frequently demonstrated to maintain the nitrite pathway for the partial nitrification (PN) process. Nevertheless, the inhibitory effect of FA and FNA would severely influence polyphosphate accumulating organisms (PAOs), destroying the microbe-based phosphorus (P) removal. Therefore, a strategic evaluation was proposed to successfully achieve biological P removal with a partial nitrification process in a single sludge system by sidestream FA and FNA dosing. Through the long-term operation of 500 days, excellent phosphorus, ammonium and total nitrogen removal performance were achieved at 97.5 ± 2.6 %, 99.1 ± 1.0 % and 75.5 ± 0.4 %, respectively. Stable partial nitrification with a nitrite accumulation ratio (NAR) of 94.1 ± 3.4 was attained. The batch tests also reported the robust aerobic phosphorus uptake based on FA and FNA adapted sludge after exposure of FA and FNA, respectively, suggesting the FA and FNA treatment strategy could potentially offer the opportunity for the selection of PAOs, which synchronously have the tolerance to FA and FNA. Microbial community analysis suggested that Accumulibacter , Tetrasphaera , and Comamonadaceae collectively contributed to the phosphorus removal in this system. Summarily, the proposed work presents a novel and feasible strategy to integrate enhanced biological phosphorus removal (EBPR) and short-cut nitrogen cycling and bring the combined mainstream phosphorus removal and partial nitrification process closer to practical application.

environmental sciences

A forward-trajectory global semi-Lagrangian transport scheme

Sludge minimization in municipal wastewater treatment by polyhydroxyalkanoate (PHA) production

PHA and EPS production from industrial wastewater by conventional activated sludge, membrane bioreactor and aerobic granular sludge technologies: A comprehensive comparison

Polyhydroxyalkanoate Production from Food Waste Coupled with Aerobic Nitrate Reduction

Coupling of Polyhydroxyalkanoate Production with Volatile Fatty Acid from Food Wastes and Excess Sludge

A contribution to resource recovery from wastewater. Anaerobic processes for organic matter and nitrogen treatment

Polyhydroxyalkanoates (PHA) Production from Fermented Thermal-Hydrolyzed Sludge by PHA-storing Denitrifiers Integrating PHA Accumulation with Nitrate Removal.

Use of skinfold thickness for estimation of body fat.

Modelling Mixed Microbial Culture Polyhydroxyalkanoate Accumulation Bioprocess towards Novel Methods for Polymer Production Using Dilute Volatile Fatty Acid Rich Feedstocks

Consistent production of high quality PHA using activated sludge harvested from full scale municipal wastewater treatment - PHARIO

Optimization of an enriched mixed culture to increase PHA accumulation using industrial saline complex wastewater as a substrate

Doubling time and annual doubling rate of human prostatic cancer.

Towards scaling-up implementation of polyhydroxyalkanoate (PHA) production from activated sludge: Progress and challenges

Polyhydroxyalkanoates production from a waste-derived feedstock driven by the reactor operating conditions: The role of biomass microbiome and its reactivation capacity

Process optimization for efficient biomediated PHA production from animal-based waste streams

Effect of culture history and carbon sources on polyhydroxyalkanoates production in activated sludge systems

Modeling the partial nitrification in sequencing batch reactor for biomass adapted to high ammonia concentrations

Improving carbon management through maximizing hydrolysis and fermentation at water resource recovery facilities

Learning Causal Polytrees

Bioplastic polyhydroxyalkanoate conversion in waste activated sludge

Insights on biological phosphorus removal with partial nitrification in single sludge system via sidestream free ammonia and free nitrous acid dosing