COX-2 inhibition attenuates lung injury induced by skeletal muscle ischemia reperfusion in rats.

Liangrong Wang,Y. Shan,Y. Ye,Li-da Jin,Qian Zhuo,Xiangqing Xiong,Xi-yue Zhao,Lina Lin,Jianxia Miao

DOI: https://doi.org/10.1016/j.intimp.2015.12.019

IF: 5.714

2016-02-01

International Immunopharmacology

Abstract:

What problem does this paper attempt to address?

Container Closure Integrity Test Using Frequency Modulation Spectroscopy Headspace Analysis with Carbon Dioxide as a Tracer Gas

Allison Alix Caudill,Ken Victor,Michael Timmins,James Veale

DOI: https://doi.org/10.5731/pdajpst.2020.011502

2020-10-16

PDA Journal of Pharmaceutical Science and Technology

Abstract:As described in USP <1207>, the container closure integrity (CCI) of a pharmaceutical package must be maintained throughout the product lifecycle to ensure sterility and stability. Current CCI test methods can be time-consuming, destructive, and lack the required sensitivity. This study presents a novel, fast, and nondestructive method for CCI testing that uses carbon dioxide as a tracer gas under effusive pressure conditions. Two types of defects were tested: laser-drilled defects located in the glass body (2, 5, and 10 μm nominal diameter) and tungsten wires inserted between the stopper and the landing seal of the vial (41, 64, and 80 μm outer diameter). During each test session, vials were placed in a pressure vessel, isolated from ambient conditions, and pressure-cycled by first pulling a vacuum and then applying an overpressure of pure carbon dioxide gas. After being exposed to 20 psig (34.7 psia) of carbon dioxide for 30 min, the overpressure was released and the vials were measured on an FMS-Carbon Dioxide Headspace Analyzer. This headspace gas analyzer utilizes a tunable diode laser absorption spectroscopy technique that employs frequency modulation to enhance measurement sensitivity. An increase of ≥1 torr in the headspace carbon dioxide content after completion of the pressure cycling procedure was intended to serve as confirmation of leak detection. All empty vials with either a 2 µm laser-drilled defect or 41 µm wire (effective defect size ~2 µm), or greater, at the stopper-seal interface were detected by this method. Furthermore, vials filled with 1 mg/mL bovine serum albumin in phosphate-buffered saline containing a 5 μm laser-drilled defect below the liquid level or a 64 µm wire (effective defect size ~6.1 µm), or greater, at the stopper-seal interface (defect above the liquid level) were detected. This test can be used for a wide variety of vial types and headspace compositions.
Preparing the target for the bullet

K. Muegge

DOI: https://doi.org/10.1038/ni0102-16

IF: 30.5

Nature Immunology

Abstract:
Evaluation of Container Closure System Integrity for Storage of Frozen Drug Products: Impact of Capping Force and Transportation

Alejandra Nieto,Holger Roehl,Michael Adler,Silke Mohl

DOI: https://doi.org/10.5731/pdajpst.2017.008383

Abstract:Frozen-state storage and cold-chain transport are key operations in the development and commercialization of biopharmaceuticals. Today, several marketed drug products are stored (and/or shipped) under frozen conditions to ensure sufficient stability, particularly for live viral vaccines. When these products are stored in glass vials with stoppers, the elastomer of the stopper needs to be flexible enough to seal the vial at the target's lowest temperature to ensure container closure integrity and thus both sterility and safety of the drug product. The container closure integrity assessment in the frozen state (e.g., -20°C, -80°C) should include container closure integrity (CCI) of the container closure system (CCS) itself, impact of processing (e.g., capping process on CCI), and impact of shipment and movement on CCI in the frozen state. The objective of this work was to evaluate the impact of processing and shipment on CCI of a CCS in the frozen state. The impact on other quality attributes was not investigated. In this light, the ThermCCI method was applied to evaluate the impact of shipping stress and variable capping force on CCI of frozen vials and to evaluate the temperature limits of rubber stoppers. In conclusion, retaining CCI during cold storage is mostly a function of vial-stopper combination, and temperatures below -40°C may pose a risk to the CCI of a frozen drug product. Variable capping force may have an influence on the CCI of a frozen drug product if not appropriately assessed. Regarding the impact of shipment on the CCI of glass vials, no indication was given at room temperature, -20°C, or -75°C when compared with static storage at such temperatures.LAY ABSTRACT: Today, several marketed products are stored (and/or shipped) under frozen conditions to ensure sufficient stability. When these products are stored in glass vials with stoppers, the elastomer of the stopper needs to be flexible enough to seal the vial and ensure container closure integrity and thus both sterility and safety of the drug product. The impact of processing and shipment on the container closure integrity (CCI) of a container closure system (vial, stopper, and flip-off cap) in the frozen state is assessed. A helium-leakage test at low temperature (ThermCCI) was used to evaluate the impact of shipping stress and variable capping force on CCI of frozen vials as well as the temperature limits of rubber stoppers. In conclusion, it was found that retaining CCI during cold storage is mostly a function of vial-stopper combination and that temperatures below -40°C may pose a risk to the CCI of a frozen drug product. Variable capping force may have an influence on the CCI of a frozen drug product if not appropriately assessed. Additionally, it was observed that the shipment of the frozen glass vials did not affect the CCI.
Method Development for Container Closure Integrity Evaluation via Headspace Gas Ingress by Using Frequency Modulation Spectroscopy

Ken G Victor,Lauren Levac,Michael Timmins,James Veale

DOI: https://doi.org/10.5731/pdajpst.2017.007518

Abstract:USP <1207.1> Section 3.5 states that "A deterministic leak test method having the ability to detect leaks at the product's maximum allowable leakage limit is preferred when establishing the inherent integrity of a container-closure system." Ideally, container closure integrity of parenteral packaging would be evaluated by measuring a physical property that is sensitive to the presence of any package defect that breaches package integrity by increasing its leakage above its maximum allowable leakage limit. The primary goals of the work presented herein were to demonstrate the viability of the nondestructive, deterministic method known as laser-based gas headspace analysis for evaluating container closure integrity and to provide a physical model for predicting leak rates for a variety of container volumes, headspace conditions, and defect sizes. The results demonstrate that laser-based headspace analysis provides sensitive, accurate, and reproducible measurements of the gas ingress into glass vial-stopper package assemblies that are under either diffusive or effusive leak conditions. Two different types of positive controls were examined. First, laser-drilled micro-holes in thin metal disks that were crimped on top of 15R glass vials served as positive controls with a well-characterized defect geometry. For these, a strong correlation was observed between the measured ingress parameter and the size of the defect for both diffusive and effusive conditions. Second, laser-drilled holes in the wall of glass vials served as controls that more closely simulate real-world defects. Due to their complex defect geometries, their diffusive and effusive ingress parameters did not necessarily correlate; this is an important observation that has significant implications for standardizing the characterization of container defects. Regardless, laser-based headspace analysis could readily differentiate positive and negative controls for all leak conditions, and the results provide a guide for method development of container closure integrity tests.LAY ABSTRACT: The new USP 39 <1207>, "Package Integrity Evaluation-Sterile Products", states in section 3.4.1: "tracer gas tests performed using … laser-based gas headspace analysis [have] been shown to be sensitive enough to quantitatively analyze leakage through the smallest leak paths found to pose the smallest chance of liquid leakage or microbial ingress in rigid packaging." In addition, USP <1207> also states that "for such methods, the limit of detection can be mathematically predicted on the basis of gas flow kinetics." Using the above statements as a foundation, this paper presents a theoretical basis for predicting the gas ingress through well-defined defects in product vials sealed under a variety of headspace conditions. These calculated predictions were experimentally validated by comparing them to measurements of changes in the headspace oxygen content or total pressure for several different positive controls using laser-based headspace analysis. The results demonstrated that laser-based headspace analysis can, by readily differentiating between negative controls and positive controls with a range of defect sizes on the micron scale, be used to assess container closure integrity. The work also demontrated that caution must be used when attempting to correlate a leak rate to an idealized defect-size parameter.
Damage Assessment of Liquid Nitrogen Filling on Type III Cylinder in Cryo-Compressed Hydrogen Storage Cylinder

Zhoutian Ge,Peiyu Hu,Liangliang Qi,Guoying Wang,Jiangkun Bai,Jianfeng Shi

DOI: https://doi.org/10.1115/pvp2024-123027

2024-01-01

Abstract:Abstract Cryo-compressed hydrogen storage is a novel on-board hydrogen storage technique. It possesses a higher hydrogen storage density and prolonged dormancy periods. Cryo-compressed hydrogen storage cylinder is the primary component for on-board hydrogen storage, where the inner cylinder with carbon fiber fully wrapped aluminum liner (Type III structure) is directly contacted with hydrogen. However, the extremely low temperature and high pressure conditions can potentially lead to damage and failure of the fiber-wrapped layer in inner cylinder. In current literature, existing research did not clearly define the variation in pressure-bearing capacity of the inner Type III cylinder after low-temperature treatment, nor the distribution and evolution of internal damage in the fiber-wrapped layer after low-temperature treatment. In this study, a inner Type III cylinder of cryo-compressed hydrogen storage cylinder with a volume of 55L and a nominal working pressure of 35MPa was prepared. After subjecting to a 16-hour liquid nitrogen treatment, a significant increase in defect density in the body of cylinder, and new delamination and matrix cracking in both heads were observed through industrial CT detection. Finally, the residual pressure-bearing capacity of inner Type III cylinder after liquid nitrogen treatment was examined through hydrostatic burst test. This study examined the influence of low temperatures on the inner Type III cylinder of cryo-compressed hydrogen storage cylinders, and also provided a guidance for the failure analysis of cylinder at low temperature conditions.
In vitro antioxidant activities and anti-proliferative properties of the functional herb Abrus cantoniensis and its main alkaloid abrine.

Mei Yang,Mazen Al Zaharna,Yu-Shan Chen,Li Li,H. Cheung

DOI: https://doi.org/10.1039/c4fo00217b

IF: 6.3173

2014-08-20

Food & Function

Abstract:Abrus cantoniensis is a common and popular vegetative food consumed as beverage, soup and folk medicine in the tropical and subtropical areas of Asia. It has been claimed valuable for cleansing toxicants in the liver. However, the functional effects of A. cantoniensis have not yet been scientifically explored. This study comprehensively evaluated the in vitro antioxidant and anti-proliferative capacities of the herbal extract and the main alkaloid abrine. Abrine was qualitatively and quantitatively determined in methanol extract (ME) using HPLC-DAD and LC-MS/MS. The results showed that ME, ethyl acetate fraction (EF) and abrine exhibited comparable ABTS radical cation scavenging activities and reducing power to two commercial antioxidants (BHT and Trolox). The EF exerted strong cellular antioxidant activity and selective cytotoxicity against three cancer cell lines in a dose-dependent manner. Biological assays revealed that the EF induced cell cycle arrest at G2/M and apoptosis in MCF-7 and Hep3B cells after 48 h of treatment. Thus, A. cantoniensis exerted potent cellular antioxidant and anti-proliferative properties, highlighting why it has been traditionally used as a functional food.
Time Temperature Superposition Evaluation and Modeling for Container Closure System's Seal Performance at Low Temperatures

Qingyu Zeng,Anthony Bucci,Le Ho

DOI: https://doi.org/10.5731/pdajpst.2019.010371

Abstract:There has been a growing interest in the assessment of container closure systems (CCS) for cold storage and shipment. Prior publications have lacked systematic considerations for the impact of dynamic time temperature transition on sealing performance associated with the viscoelastic characteristics of rubber stoppers used in container closure systems (CCSs). This paper demonstrates that sealing performance changes inherently and is fundamentally both time- and temperature-dependent. Our research results display this critical time temperature transition impact on CCS sealing performance by applying compression stress relaxation (CSR) on a rubber stopper for experimental data collection and modeling evaluation. The experimental results agree with modeling evaluation following Maxwell-Wiechert theory and the time temperature superposition based on the Arrhenius and Williams-Landel-Ferry methods. Both testing and modeling data show good consistency, demonstrating that the sealing force inevitably changes over time together with temperature transition because of the viscoelastic nature of the rubber stoppers. Our results show that compression seal force decreases quickly as temperature decreases. The significant loss of rubber stopper sealing force at lower temperature transitions could contribute significant risk to CCI at low storage and transport temperatures. Modeling evaluation, with a powerful capability to handle actual testing data, can be employed as a predictive tool to evaluate the time- and temperature-dependent sealing force throughout the entire sealed drug product life span. The present study is only applicable before reaching the rubber glass transition temperature Tg - a critical transition phase that can not be skipped/separated from real time temperature transition, and it will further determine the CCS sealing performance while approaching cryogenic temperature. The present work provides a new, integrated methodology framework and some fresh insights to the parenteral packaging industry for practically and proactively considering, designing, setting up, controlling, and managing stopper sealing performance throughout the entire sealed drug product life span.
Leakage dynamics of glass bottles on container closure integrity testing: Influence of different laser-drilled microhole geometries

Weina Han,Xiaofeng Duan,Jianying Wu,Lan Jiang,Hao Wu,Zhaolun Chen

DOI: https://doi.org/10.1016/j.xphs.2023.01.013

IF: 3.8

2023-01-26

Journal of Pharmaceutical Sciences

Abstract:Container closure integrity testing (CCIT) is a critical step in ensuring package integrity and providing feedback on package designs. In practical applications, CCIT methods, namely physical and probabilistic methods, must be appropriately selected and validated to ensure their suitability for the intended use. However, the industry still lacks practical recommendations regarding the choice of CCIT methods and artificial leaks to set the acceptance criteria. The main reason is the lack of correlation between testing methods. Artificially introduced leak microholes are the only way to determine the sensitivity of a CCIT method and to implement the method correlation. However, the type of artificial leakage is a key factor because in most studies, leakage is described and valued using a single parameter, such as size. This can significantly affect the credibility of the relevant test results, especially in the case of microbial invasion, where the difference in test conditions and samples will severely affect the probability of microbial invasion. Therefore, it is vital to conduct a systematic study on the influence of leakage conditions on CCIT methods. In this study, the influence of the shapes of artificial leaks on the two kinds of testing methods was systematically studied based on a laser-drilled microhole—a highly potential and non-exogenous artificial leak manufacturing method that can fabricate different leakage geometries. The reason for the influence of the shape of an artificial leak on the CCIT is that the deterministic method takes defects as an idealized model and ignores the influence of the leak shape, wall thickness, and other factors on leakage and pollution risks. However, these factors seriously affect the dynamic process of leakage and microbial invasion. The pressure decay method is used to test the leakage flow rate of conical and straight holes. Microbial challenge tests are then used to verify the impact of leakage shapes on the pollution risk. The results of the tests indicated that the probability of microbial invasion in the conical holes is much higher than that in straight holes with the same flow test results and that the wall thickness can also affect microbial invasion. Thus, it can be proven that the risk of leakage and invasion or the sensitivity of different methods cannot only be compared through the leak diameter. Numerous influencing factors, including leakage geometry (e.g., shape and thickness), must be considered in practical applications.

pharmacology & pharmacy,chemistry, medicinal, multidisciplinary
Preliminary Results for a New Final Package Test to Assess the Quality of Sterile Package Systems

Hartmut Dunkelberg,Silke Wedekind

DOI: https://doi.org/10.1086/502287

2004-01-01

Infection Control and Hospital Epidemiology

Abstract:Abstract Objectives: To develop a microbial test method to ascertain the passage of airborne bacteria through the medical device packaging System after sterilization, and to apply this test method to flexible packages under mechanical pressure changes. Methods: Petri dishes filled with nutrient agar were integrated into the packaging unit prior to sterilization. We examined paper packaging consisting of 1 (single-paper packaging [P]), 2 (double-paper packaging [PP] and textile and paper double packaging [TP]), and 3 (double packaging with transport packaging [TPP]) layers. After sterilization, the test packages were pressed five times per minute for 1 or 3 hours by a mechanical device weighing 1 kg. This exposure took place in rooms with an average airborne bacterial count of 35 (room 1) or 440 (room 2) CFU/m 3 . The packaging was opened following culture at 37° C for 48 hours to determine the number of colonies formed. Results: The proportion of contaminated packages rose with the duration of mechanical stress and increased airborne bacteria concentration. Thus, mechanical pressure change for 3 hours resulted in the contamination of 60% (P), 15% (PP), 0% (TP), and 0% (TPP) of the packages in room 1, whereas 100% (P), 65% (PP), 73% (TP), and 0% (TPP) of the packages in room 2 were contaminated. Conclusions: This test method allows sterile packaging Systems to be tested for contamination under practical conditions without extensive laboratory preparation. Contamination as a resuit of laboratory errors can be ruled out almost certainly.

infectious diseases,public, environmental & occupational health
Dynamics of the Fas-and stress-induced apoptosis of human neutrophils under the action of endotoxins

M. Vinokurov,M. Yurinskaya,A. Suslikov,V. Pechatnikov,S. Grachev

DOI: https://doi.org/10.1134/S0012496606050012

2006-09-01

Doklady Biological Sciences

Abstract:
Case Study: Compatibility Testing of Pre-Filled Syringe Stopper Technology with Vaporized Hydrogen Peroxide Terminal Sterilization Process

Juha Mattila,Michael Kienzle,Arja Ruley

DOI: https://doi.org/10.5731/pdajpst.2024.012965

2024-08-23

Abstract:STERIS and W.L. GORE collaborated on a case study testing the compatibility of a new prefilled syringe plunger design with VHP terminal sterilization. VHP chamber conditions require deep vacuum pulsing, which may represent challenges to prefilled syringe container integrity. The growing industry trend toward VHP sterilization is driven by the FDA search for alternative sterilization methods to EO and the recent publication of a VHP specific process standard. The purpose of the study is to test and report compatibility of the new 0.5 mL GORE IMPROJECT plunger, a silicone free syringe solution for ophthalmic application, with VHP sterilization. Various challenges have been reported when using conventional, siliconized, prefilled syringe systems for intravitreal injections such as subvisible particles, inflammation, silicone floaters, and intraocular pressure increases. The GORE plunger eliminates the need for silicone oil as a lubricant on the plunger and barrel, while meeting strict container closure and terminal sterilization requirements of ophthalmic applications. This case study presents successful results of deep vacuum VHP terminal sterilization process compatibility with the GORE plunger design and material composition. Test results include primary container integrity, stopper off-gassing/ingress, and visual inspection. Principles of VHP vacuum sterilization process, test cycle configuration, and its main parameters are presented.
High-voltage leak detection of a parenteral proteinaceous solution product packaged in form-fill-seal plastic laminate bags. Part 1. Method development and validation

Rasmus Damgaard,Mats Rasmussen,Peter Buus,Brian Mulhall,Dana Morton Guazzo

DOI: https://doi.org/10.5731/pdajpst.2013.00945

Abstract:In Part 1 of this three-part research series, a leak test performed using high-voltage leak detection (HVLD) technology, also referred to as an electrical conductivity and capacitance leak test, was developed and validated for container-closure integrity verification of a small-volume laminate plastic bag containing an aqueous solution for injection. The sterile parenteral product is the rapid-acting insulin analogue, insulin aspart (NovoRapid®/NovoLog®, by Novo Nordisk A/S, Bagsværd, Denmark). The aseptically filled and sealed package is designed to preserve product sterility through expiry. Method development and validation work incorporated positive control packages with a single hole laser-drilled through the laminate film of each bag. A unique HVLD method characterized by specific high-voltage and potentiometer set points was established for testing bags positioned in each of three possible orientations as they are conveyed through the instrument's test zone in each of two possible directions-resulting in a total of six different test method options. Validation study results successfully demonstrated the ability of all six methods to accurately and reliably detect those packages with laser-drilled holes from 2.5-11.2 μm in nominal diameter. Part 2 of this series will further explore HVLD test results as a function of package seal and product storage variables. The final Part 3 will report the impact of HVLD exposure on product physico-chemical stability. Lay abstract: In this Part 1 of a three-part research series, a leak test method based on electrical conductivity and capacitance, called high voltage leak detection (HVLD), was used to find leaks in small plastic bags filled with an insulin pharmaceutical solution for human injection by Novo Nordisk A/S (Bagsværd, Denmark). To perform the test, the package is electrically grounded while being conveyed past an electrode linked to a high-voltage, low-amperage transformer. The instrument measures the current that passes from the transformer to the electrode, through the packaged product and along the package walls, to the ground. Plastic packages without defect are relatively nonconductive and yield a low voltage reading; a leaking package with electrically conductive solution located in or near the leak triggers a spike in voltage reading. Test methods were optimized and validated, enabling the detection of leaking packages with holes as small as 2.5 μm in diameter. Part 2 of this series will further explore HVLD test results as a function of package seal and product storage variables. The final Part 3 will report the impact of HVLD exposure on product stability.
Investigations of aged metal seals for transport package safety assessment

Annette Rolle,Tino Neumeyer,Viktor Ballheimer,Frank Wille

DOI: https://doi.org/10.5194/sand-2-23-2023

2023-09-06

Safety of Nuclear Waste Disposal

Abstract:Abstract. Acceptable limits for activity release from transport casks for high-level radioactive material specified in the IAEA regulations must be kept by the integrity of cask body and the cask sealing system. BAM – the German competent authority for mechanical, thermal and containment assessment of packages liable for approval – verifies the activity release compliance with the regulatory limits. One of the fundamental aspects in assessment is the specification of conservative package design leakage rates. To ensure the required package tightness for both storage and transport of the cask before and after storage, usually metal seals of the HELICOFLEX® type are used. Due to long-term use, the seal behaviour is influenced by temperature and time. The mechanical and thermal loadings associated with the routine, normal and accident conditions of transport specified in the regulations can have a significant effect on the leak tightness of the sealing system. Whereas the safety for application of new, non-aged HELICOFLEX® seals is verified sufficiently, there are still technical data gaps concerning the efficiency of aged HELICOFLEX® seals. BAM performed experiments to learn more about the sealing efficiency of aged HELICOFLEX® seals with aluminium and silver outer jackets. The seals were compressed in test flanges, and for artificial ageing the complete flange systems were stored in an oven for several months at a high temperature. During the compression and decompression tests after the ageing, load-deformation characteristics of the seals and leakage rates were measured. With these tests a load situation was simulated, which can occur in the regulatory drop test of the cask: under high-impact loads the bolted lid can lift a little for a short moment, allowing a little movement of the seal so that the contact area can change before compressing again. The poster presentation will show details about test conditions and first results.
Assessing efficacy of standard impregnation techniques on die-cast aluminum alloys using X-ray micro-CT

Bandara, Ajith

DOI: https://doi.org/10.1007/s41230-024-3049-2

2024-06-06

China Foundry

Abstract:Utilizing lightweight Al alloys in various industrial applications requires achieving precise pressure tightness and leak requirements. Vacuum pressure impregnation (VPI) with thermosetting polymers is commonly used to address leakage defects in die-cast Al alloys. In this study, the efficacy of the VPI technique in sealing alloy parts was investigated using a combination of nondestructive micro X-ray computed tomography (micro XCT) and a standard leak test. The results demonstrate that the commonly used water leak test is insufficient for determining the sealing performance. Instead, micro XCT shows distinct advantages by enabling more comprehensive analysis. It reveals the presence of a low atomic number impregnates sealant within casting defects, which has low grey contrast and allows for visualizing primary leakage paths in 3D. The effective atomic number of impregnated resin is 6.75 and that of Al alloy is 13.69 by dual-energy X-ray CT. This research findings will contribute to enhancing the standard VPI process parameters and the properties of impregnating sealants to improve quality assurance for impregnation in industrial metals.

metallurgy & metallurgical engineering
Letter: Malnutrition: an unappreciated "at risk" group.

B. Richardson

Transactions of the Royal Society of Tropical Medicine and Hygiene

Abstract:
Integrity Experiments for Geological Carbon Storage (GCS) in Depleted Hydrocarbon Reservoirs: Wellbore Components under Cyclic CO2 Injection Conditions

Taofik H. Nassan,Carsten Freese,Dirk Baganz,Hakan Alkan,Oleksandr Burachok,Jonas Solbakken,Nematollah Zamani,Morten Gunnar Aarra,Mohd Amro

DOI: https://doi.org/10.3390/en17123014

IF: 3.2

2024-06-19

Energies

Abstract:Integrity of wellbores and near wellbore processes are crucial issues in geological carbon storage (GCS) projects as they both define the confinement and injectivity of CO2. For the proper confinement of CO2, any flow of CO2 along the wellbore trajectory must be prevented using engineered barriers. The effect of cyclic stimuli on wellbore integrity, especially in the context of GCS projects, has been given less attention. In this study, the effect of pressure- and temperature-cycling on two types of wellbore composites (i.e., casing-cement and cement-caprock) have been investigated experimentally in small- and large-scale laboratory setups. The experiments have been carried out by measuring the effective permeability of the composites under pressure and thermal cyclic conditions. Furthermore, the permeability of individual samples (API class G and HMR+ cement and caprock) was measured and compared to the permeability of the composites. The results indicate that the permeability of API class G cement when exposed to CO2 is in the order of 10−20 m2 (10−5 mD) as a result of the chemical reaction between the cement and CO2. In addition, the tightness of the composite cement–rock has been confirmed, while the permeability of the composite casing–cement falls within the acceptable range for tight cement and the CO2 flow was identified to occur through or close to the interface casing–cement. Results from thermal cycling within the range −9 to 14 °C revealed no significant effect on the integrity of the bond casing–cement. In contrast, pressure cycling experiments showed that the effective pressure has a larger influence on the permeability. The potential creation of micro-cracks under pressure variations may require some time for complete closing. In conclusion, the pressure and temperature cycling from this study did not violate the integrity of the casing–cement composite sample as the permeability remained low and within the acceptable range for wellbore cement.

energy & fuels
Real-Time Monitoring of the Effect of CO2 on the Cement Sheath

Paul Wagner,Kris Ravi,Michael Prohaska

DOI: https://doi.org/10.2118/200931-ms

2021-06-28

Abstract:Abstract Global warming is one of the most significant issues the world is facing. Capturing carbon dioxide from the atmosphere or industrial processes and storing it in geological formations (carbon capture and storage, CCS) can help counteract climate change. Nevertheless, the interaction between well barrier elements such as cement, casing, tubulars, packers, and valves can lead to possible leakages. To accomplish successful carbon dioxide sequestration, injecting the carbon dioxide in its supercritical state is necessary. The supercritical carbon dioxide can corrode steel and elastomers and react with the calcium compounds in the cement, dissolving them and forming calcium carbonate and bicarbonate in the process. This carbonation can lead to channels forming on the cement-to-rock interface or cracking due to the carbonate precipitation, resulting in a loss of well integrity. This study focusses on finding ways that enable the continuous monitoring of cement integrity, under in-situ conditions, in a lab setup. The construction of an autoclave, capable of withstanding supercritical conditions of carbon dioxide, facilitates the in-situ monitoring. This autoclave also makes CT-scans of the pressurized sample possible, as well as acoustic measurements, using state-of-the-art piezo elements. The first tests will establish a baseline using neat Class G Portland cement to verify the design and sensors. The set up consists of a rock core in the middle of the autoclave surrounded by a cement sheath. A prepared channel in the center of the core expedites the distribution of the carbon dioxide. Once the ability of the sensors to monitor the integrity is verified, different cement compositions and their interaction with supercritical carbon dioxide can be studied. The experimental setup and the procedure discussed here closely simulate the downhole condition. Hence, the results obtained using this setup and procedure is representative of what could be observed downhole. The direction is not to remove the sample from the autoclave for analysis, as is the current industry practice, but to measure cement integrity under in-situ conditions over an extended period of time. Digitalization is powering the in-situ analysis in these tests. The first two tests of this study, using the afore mentioned autoclave, investigated the carbonation behaviour of two Class G Portland cement slurrys, one with a low and one with a high slurry-density. The low-density slurry showed extensive degradation and even the high-density slurry showed carbonation, but only close to the sandstone core. The results from this study can lead to the prevention of leakage of carbon dioxide to the environment and other formations, which defeats the purpose of carbon dioxide sequestration. These results should improve the economics of these wells as well as the health, safety, and environmental aspects.
A Novel MATLAB®-Algorithm-Based Video Analysis to Quantitatively Determine Solution Creeping in Intact Pharmaceutical Glass Vials

Daniel Molnar,Martina Röhm,Johannes Wutz,Ingrid Rivec,Annika Michel,Gina Klotz,Jürgen Hubbuch,Katharina Schindowski,Ingo Presser

DOI: https://doi.org/10.1016/j.ejpb.2022.08.003

Abstract:During the filling process of a biopharmaceutical drug product (DP), a liquid DP film might creep up the inner vial wall which is barely discernible, appears as milky-white haze after lyophilisation and is known as fogging. Creeping and fogging are mainly dependent on the primary packaging material surface and its hydration, vial preparation process as well as DP composition. The occurrence of both can impede visual inspection and might lead to DP rejection. Hence, our studies focused on the early detection of liquid solution and glass vial surface interaction directly after filling. For a fast and highly sensitive evaluation a novel video-based analysis was used. To our knowledge, this is the first time a MATLAB®-algorithm-based video analysis was applied to quantitatively determine creeping time-resolved. Furthermore, creeping in dependence of vial processing sites, surfactant type and concentration, filling temperature, and vial format were investigated. The results were verified using orthogonal conventional methods such as surface tension, wetting behaviour, and contact angle measurements, as well as ToF-SIMS, ICP-MS, and SEM. Additionally, the methods applied were assessed regarding their cross-validation capability. The observations indicate that the vial preparation process can have a pronounced impact on alteration of the glass vial surface and related creeping behaviour of the filled solution.
Investigation of heat leakage calculations and experiments for a wide-mouth liquid nitrogen tank

Renchao Tong,Ankuo Zhang,Shuling Guo,Xiaoli Gong

DOI: https://doi.org/10.1080/15567036.2024.2413864

2024-10-15

Energy Sources Part A Recovery Utilization and Environmental Effects

Abstract:With the continuous development of biomedicine, the long-term low-temperature storage of biological samples has become essential. In order to meet the demand for long-term storage of liquid nitrogen to keep samples safe, a study on the evaporated gas recycling storage of liquid nitrogen tanks will be carried out. This research utilizes new approach to accurately calculate the heat leakage of the liquid nitrogen tank. The experimental results show that the theoretical heat leakage is 6.16 W, and the actual heat leakage is 7.07 W. By incorporating the insulating plug, the actual heat leakage was reduced by 61.2%, decreasing to 2.74 W, and the calculated heat leakage is 2.47 W. The error margin in both cases was approximately 10%. Furthermore, in contrast to existing investigations, this experiment with the 8W@77K pulse tube cryocooler for recovering nitrogen is conducted under environmental pressure rather than overpressure, and it also takes into account the sensible heat issues caused by ambient pressure. The ratio of 1.81 W of sensible heat to 2.74 W of latent heat is 2:3, indicating that under ambient pressure conditions, the impact of sensible heat cannot be ignored. The key improvement methods are given to improve the success rate of the experiment. The research results provide a useful reference for the re-cycling and storage of liquid nitrogen.

energy & fuels,engineering, chemical
An accurate detection of micro-collapse during the lyophilisation of a 5% w/v lactose solution using a combination of novel techniques: intelligent laser speckle imaging (ILSI) and through-vial impedance spectroscopy (TVIS)

Ahmet Orun,Anand Vadesa,Geoff Smith

2024-06-12

Abstract:Context: In a freeze drying (FD) process, an accurate observation and control of the process parameters at critical stages are at high importance. Particularly accurate and timely identification of the critical temperature (TC) at the end of primary drying phase would lead to heating energy cost reduction and product waste elimination by ending the process before the product's micro-collapse stage. Aim: Within this work, a combination of novel techniques optical technique called Intelligent Laser Speckle Imaging (ILSI) in association with product image texture analysis, coupled to an electrical impedance technique called through vial impedance spectroscopy (TVIS) has been applied onto the real-time product states observation process to identify the specific structural product surface/subsurface characteristics and hence the micro-collapse stage. Method: 2 cycles - one providing a profile for standard approach (non-collapsed) and another with a temperature ramp through TC to micro-collapse, TVIS provides an assessment of the onset of micro-collapse through the assessment of the acceleration in drying rate whereas the ILSI with pattern recognition detects the change in microstructure

Image and Video Processing

COX-2 inhibition attenuates lung injury induced by skeletal muscle ischemia reperfusion in rats.

Container Closure Integrity Test Using Frequency Modulation Spectroscopy Headspace Analysis with Carbon Dioxide as a Tracer Gas

Preparing the target for the bullet

Evaluation of Container Closure System Integrity for Storage of Frozen Drug Products: Impact of Capping Force and Transportation

Method Development for Container Closure Integrity Evaluation via Headspace Gas Ingress by Using Frequency Modulation Spectroscopy

Damage Assessment of Liquid Nitrogen Filling on Type III Cylinder in Cryo-Compressed Hydrogen Storage Cylinder

In vitro antioxidant activities and anti-proliferative properties of the functional herb Abrus cantoniensis and its main alkaloid abrine.

Time Temperature Superposition Evaluation and Modeling for Container Closure System's Seal Performance at Low Temperatures

Leakage dynamics of glass bottles on container closure integrity testing: Influence of different laser-drilled microhole geometries

Preliminary Results for a New Final Package Test to Assess the Quality of Sterile Package Systems

Dynamics of the Fas-and stress-induced apoptosis of human neutrophils under the action of endotoxins

Case Study: Compatibility Testing of Pre-Filled Syringe Stopper Technology with Vaporized Hydrogen Peroxide Terminal Sterilization Process

High-voltage leak detection of a parenteral proteinaceous solution product packaged in form-fill-seal plastic laminate bags. Part 1. Method development and validation

Investigations of aged metal seals for transport package safety assessment

Assessing efficacy of standard impregnation techniques on die-cast aluminum alloys using X-ray micro-CT

Letter: Malnutrition: an unappreciated "at risk" group.

Integrity Experiments for Geological Carbon Storage (GCS) in Depleted Hydrocarbon Reservoirs: Wellbore Components under Cyclic CO2 Injection Conditions

Real-Time Monitoring of the Effect of CO2 on the Cement Sheath

A Novel MATLAB®-Algorithm-Based Video Analysis to Quantitatively Determine Solution Creeping in Intact Pharmaceutical Glass Vials

Investigation of heat leakage calculations and experiments for a wide-mouth liquid nitrogen tank

An accurate detection of micro-collapse during the lyophilisation of a 5% w/v lactose solution using a combination of novel techniques: intelligent laser speckle imaging (ILSI) and through-vial impedance spectroscopy (TVIS)