Abstract:NASICON-type Li1+xAlxTi2−x(PO4)3 (LATP) solid electrolytes have developed as a promising candidate for solid-state lithium batteries. However, the brittle and stiff LATP suffers from poor physical contact with electrodes and chemical/electrochemical instability at electrode|electrolyte interfaces. Herein, a thin and flexible hybrid electrolyte comprised of LATP and poly(vinylidene fluoride-trifluorethylene) (PVDF-TrFE) incorporated with highly concentrated ionic liquid electrolyte (ILE) is prepared to resolve these prominent limitations. To further protect the LATP|Li interface, an ultrathin poly[2,3-bis(2,2,6,6-tetramethylpiperidine-N-oxycarbonyl)-norbornene] (PTNB) polymer is coated on Li, acting as an additional protective layer. Consequently, the lithium stripping-plating lifetime is prolonged from 128 to 792 h, with no dendritic lithium observed. The PTNB@Li||LiNi0.8Co0.1Mn0.1O2 (PTNB@Li||NCM811) cells achieve significantly improved rate capability and cycling stability, predominantly resulting from the drastically decreased interfacial resistances, prohibited dendritic lithium generation, mitigated cathode material phase evolution, and prevention of internal microcrack formation. The thinner interphases formed on NCM811 and PTNB@Li electrodes also play a key role. The quasi-solid-state batteries allow for the fabrication of multi-layer bipolar cells with stable cycling. Even under some exertive circumstances, (limited lithium source, low temperature, e.g., 0 °C), the impressive electrochemical performance achieved highlights the importance of such quasi-solid-state lithium batteries as a viable solution for the next-generation high-performance lithium batteries.

Quasi-Solid-State Lithium Metal Batteries Using the LiNi0.8Co0.1Mn0.1O2-Li1+ xAlxTi2- x(PO4)3 Composite Positive Electrode

Aqueous Tape Casting Phosphate Ceramic Electrolyte Membrane for High Performance All Solid-State Lithium Metal Battery

LATP-coated LiNi0.8Co0.1Mn0.1O2 cathode with compatible interface with ultrathin PVDF-reinforced PEO-LLZTO electrolyte for stable solid-state lithium batteries

LATP-coated LiNi 0.8 Co 0.1 Mn 0.1 O 2 Cathode with Compatible Interface with Ultrathin PVDF-reinforced PEO-LLZTO Electrolyte for Stable Solidstate Lithium Batteries

Recent Advances in Li1+xAlxTi2−x(PO4)3 Solid-State Electrolyte for Safe Lithium Batteries

High-performance lithium metal batteries based on composite solid-state electrolytes with high ceramic content

High Li+ Conductivity of Li1.3+xAl0.3−xMgxTi1.7(PO4)3 with Hybrid Solid Electrolytes for Solid‐State Lithium Batteries

Asymmetric Solid-State Lithium-Metal-Battery Electrolytes Featuring Na Superionic Conductor-Type Ceramic and Garnet-Type Ceramic Filled Composite Polymer

Stabilizing Li<sub>1.3</sub>Al<sub>0.3</sub>Ti<sub>1.7</sub>(PO<sub>4</sub>)<sub>3</ sub>|Li Metal Anode Interface in Solid-State Batteries by Kevlar Aramid Nanofiber-Based Protective Coating

Metal-Doped NASICON/Polymer Composite Solid Electrolyte for Lithium Titania Anode in Lithium-Ion Batteries

Highly Stable Quasi‐Solid‐State Lithium Metal Batteries: Reinforced Li 1.3 Al 0.3 Ti 1.7 (PO 4 ) 3 /Li Interface by a Protection Interlayer

Interface engineering of Li<sub>1.3</sub>Al<sub>0.3</sub>Ti<sub>1.7</sub>(PO<sub>4</sub>)<sub>3</ sub> ceramic electrolyte via multifunctional interfacial layer for all-solid-state lithium batteries

Interfacial Stability of Phosphate-NASICON Solid Electrolytes in Ni-Rich NCM Cathode-Based Solid-State Batteries

Stabilizing LATP Electrolyte Interface of All-Solid-State Lithium Ion Batteries Consisting of High-Voltage Cathode

Interface Regulation Enabling Three-Dimensional Li1.3Al0.3Ti1.7(PO4)3-reinforced Composite Solid Electrolyte for High-Performance Lithium Batteries

Stabilized Cathode/Sulfide Electrolyte Interface through Conformally Interfacial Nanocoating for All-Solid-State Batteries

Achieving stable all-solid-state lithium-metal batteries by tuning the cathode-electrolyte interface and ionic/electronic transport within the cathode

Hybrid solid state electrolytes blending NASICON-type Li1+xAlxTi2–x(PO4)3 with poly(vinylidene fluoride-co-hexafluoropropene) for lithium metal batteries

Insight into the Extreme Side Reaction between LiNi<sub>0.5</sub>Co<sub>0.2</sub>Mn<sub>0.3</sub>O<sub>2</sub> and Li<sub>1.3</sub>Al<sub>0.3</sub>Ti<sub>1.7</sub>(PO<sub>4</sub>)<sub>3</ sub> during Cosintering for All-Solid-State Batteries

LATP-coated NCM-811 for high-temperature operation of all-solid lithium battery

Roles of Lithium Aluminum Titanium Phosphate in Lithium Batteries