Abstract:Abstract Basic oxygen furnace (BOF) steelmaking is a widely used method for steelmaking production, and the bath stirring has a significant influence on dynamics of bath flow and mixing. Therefore, the effect of bottom gas flowrate, nozzle number and configuration, and bottom gas distribution mode on bath stirring are summarized in this study. Reasonable matching of bottom gas flowrate, nozzle number and configuration, as well as intensive study on the coupling effect of gas flowrate gradient and exchange frequency on non-uniform stirring would receive more and more attention in the coming years. With wide concern on the low-carbon and high-efficient production for BOF steelmaking, as a kind of recyclable iron-containing resource, the rapid melting and reasonable utilization of scrap in converter bath were emphasized in recent works, which could be promoted with high-efficient bottom stirring. The effect of bottom stirring on heat and mass transfer during scrap melting process was reviewed in this work, and the influence mechanism of bottom stirring on coupled heat and mass transfer should be further investigated. In addition, an overview of recently published physical and numerical simulation describing the bottom stirring and its effect on scrap melting would provide an outlook for future work.

What problem does this paper attempt to address?

The paper primarily explores the impact of bottom stirring on the mixing and mass transfer behavior of the molten pool during the converter steelmaking process. Specifically, the paper focuses on the following aspects: 1. **Bottom Gas Flow Rate**: - The paper summarizes the effects of different bottom gas flow rates on the mixing of the molten pool. An appropriate increase in the bottom gas flow rate can reduce the mixing time and increase the average flow rate of the molten steel. However, when the gas flow rate is too high, it can cause violent oscillations in the molten pool, thereby reducing the mixing effect. 2. **Number and Configuration of Nozzles**: - The number and layout of nozzles have a significant impact on the internal mixing of the molten pool. By reasonably configuring the position and angle of the nozzles, the flow pattern within the molten pool can be optimized, thereby improving the mixing effect. The study found that nozzles placed too close to the furnace wall can cause violent collisions, wasting stirring energy. 3. **Bottom Gas Distribution Pattern**: - The bottom gas distribution pattern is divided into uniform and non-uniform modes. The non-uniform mode improves the flow and mixing effect within the molten pool by forming asymmetric large-scale circulation. The study shows that the linear scheme under the non-uniform mode can significantly shorten the mixing time and increase the mass transfer rate between slag and steel. 4. **Rapid Melting of Scrap Steel**: - In the context of low-carbon and efficient steelmaking, the paper emphasizes accelerating the melting process of scrap steel in the molten pool by optimizing bottom stirring parameters. Bottom stirring enhances heat transfer and mass transfer within the molten pool, helping to achieve rapid melting of scrap steel. This provides a reasonable and practical solution for the effective utilization of scrap steel. In summary, the paper aims to improve the flow and mixing characteristics of the molten pool during the converter steelmaking process by optimizing bottom stirring parameters (such as gas flow rate, number and configuration of nozzles, and gas distribution pattern), to achieve efficient production and full utilization of scrap steel resources.

Effect of bottom stirring on bath mixing and transfer behavior during scrap melting in BOF steelmaking: A review

Numerical Simulation of Bottom-Blowing Stirring in Different Smelting Stages of Electric Arc Furnace Steelmaking

Numerical simulation of flow characteristics of side-bottom combined blowing in iron bath reactor

Flow, Heat‐Transfer, and Mixing Behaviors of Scrap Steel in a Refining Ladle with Bottom Blowing

Numerical Simulation of Multiphase Flow in Ironmaking Process for Oxygen-Rich Side-Blown Bath Smelting Furnace

Numerical simulation on the melting kinetics of steel scrap in iron-carbon bath

Numerical Investigation on Role of Bottom Gas Stirring in Controlling Thermal Stratification in Steel Ladles

Numerical Simulation of the Interaction Between Supersonic Oxygen Jets and Molten Slag–Metal Bath in Steelmaking BOF Process

Study on the synergistic effect of electromagnetic stirring and mechanical reduction on the improvement of the internal homogeneity of high-carbon steel billet

Influence of Electromagnetic Swirling Flow in Nozzle on Solidification Structure and Macrosegregation of Continuous Casting Square Billet

Demystifying the Mushroom Formation Mechanism in BOF Steelmaking Using Physical Modeling Approach and Plant Trial

A review of electromagnetic stirring on solidification characteristics of molten metal in continuous casting

Numerical investigation on effect of electromagnetic stirring on macrosegregation in continuously cast round bloom via three-phase solidification model

A Review of Physical and Numerical Approaches for the Study of Gas Stirring in Ladle Metallurgy

Mathematical Modeling on the Multiphase Flow during Top–Bottom Combined Blowing Basic Oxygen Furnace Steelmaking Process

Research on the Advantages of Vortex Smelting Reduction of High-Iron Red Mud (Bauxite Residue)

Solid Flow in an Experimental Oxygen Blast Furnace Model: Effects of Recycled Gas and Raceway

Physical Simulation and Industrial Testing of Bottom-Blown O2-CaO Converter for Steelmaking Process

Research on Top and Bottom Mixed Blowing CO2 in Converter Steelmaking Process

Effects of CO 2 reaction-induced bubble proliferation on the dynamic conditions of stainless steel smelting molten pool