The ultimate properties of bone tissue: the effects of yielding.

A. Burstein,J. Currey,V. Frankel,D. Reilly

DOI: https://doi.org/10.1016/0021-9290(72)90017-6

IF: 2.4

Journal of Biomechanics

Abstract:

What problem does this paper attempt to address?

Preparation of double linked waterborne epoxy resin coating using Titanium curing agent and aminopropyltriethoxysilane and its anticorrosive properties

Lingli Xu,,

DOI: https://doi.org/10.20964/2021.07.07

IF: 1.541

2021-07-01

International Journal of Electrochemical Science

Abstract:To obtain a waterborne coating with excellent anticorrosion performance, a titanium ion-containing curing agent and polysiloxane were used separately and together to cure epoxy resin coatings. Fourier transform infrared (FTIR) spectroscopy was employed to investigate the curing process. An immersion test in NaCl solution was performed, and then, the morphology changes of different coatings were observed by field emission scanning electron microscopy (FESEM). Electrochemical impedance spectroscopy (EIS) and copper-accelerated acetic acid salt spray (CASS) testing were conducted to characterize the corrosion resistance of the coatings. The FTIR spectra showed that when both agents were used, the curing process of the resin involved three stages, which resulted in much denser crosslinks than when using a single agent. After immersion, numerous cracks were observed on coatings cured with a single agent, whereas the double-agent-cured coating remained integrated. The impedance of the double-agent-cured coating reached 8.5×108 Ω cm2 and remained as high as 1.7×108 Ω cm2, even after 40 days of immersion.

electrochemistry
Preparation and Properties of Waterborne Acrylic-Modified Epoxy Phosphate Resin and Its Coating

Fei Xiao,Tao Yong,Tianlong Cao,Fangyuan Shi,Xuejun Sun,Jin Zhang

DOI: https://doi.org/10.3390/coatings14091129

IF: 3.236

2024-09-03

Coatings

Abstract:An acrylic acid-modified epoxy phosphate resin coating was synthesized by a four-step method marked "A-B-C-D", and it was used as an efficient protective layer for steel structures. The coating exhibited good properties, mainly including water resistance (≥240 h), salt spray resistance (≥300 h), surface drying time (≤1 h), and adhesion (≥6.5 MPa).

materials science, multidisciplinary,physics, applied, coatings & films
Tannic acid‐copper metal‐organic frameworks decorated graphene oxide for reinforcement of the corrosion protection of waterborne epoxy coatings

Li Cheng,Peimin Hou,Chengbao Liu

DOI: https://doi.org/10.1002/maco.202213189

2022-05-04

Materials and Corrosion

Abstract:This study presents the preparation and failure evolution mechanism of novel waterborne epoxy coating. Tannic acid‐copper frameworks decorated with graphene oxide (TAG) were incorporated into the waterborne epoxy coating. Results proved that the embedded TAG significantly enhanced the impermeability of epoxy coating. Meanwhile, the localized corrosion reaction at the coating/steel interface was effectively inhibited. Waterborne anticorrosion coatings have aroused tremendous attention in the metal protection field due to their environmentally friendly properties. However, the limited barrier performance and poor resistance to corrosive species severely impede its practical applications. Herein, tannic acid‐copper metal‐organic framework (TA‐Cu) was first synthesized via oxidative coordination and then assembled with graphene oxide to obtain TA‐Cu‐decorated graphene oxide (TAG), which was utilized to improve the anticorrosion performance of waterborne epoxy (WEP) coatings. Electrochemical measurements demonstrated that the impermeability of WEP has been significantly enhanced with the incorporation of TAG. Meanwhile, local electrochemical impedance spectroscopy tests indicated that the corrosion reaction at defected region can be effectively suppressed, presenting an active anticorrosion function. The protection mechanisms are attributed to (1) TA‐Cu contributed to the dispersion of graphene oxide in WEP and impeded the intrusion of aggressive ions and (2) the coordination and adsorption of TA on steel inhibited the redox process and corrosion extension.
Corrosion resistance of a self-curing waterborne epoxy resin coating

Gongwen Tang,TingTing Ren,Zhishan Yan,Linrong Ma,Xianhui Pan,Jing Liu,Xiangyu Hou,Xin Huang

DOI: https://doi.org/10.1007/s11998-018-00166-2

2019-01-10

Journal of Coatings Technology and Research

Abstract:Waterborne coatings have gained more and more attention as a method to protect the environment. However, the application of waterborne coatings to metals, especially for sufficient long-term protection in harshly corrosive environments, is still limited. Here, we report a self-curing waterborne coating with good corrosion resistance. First, a self-curing waterborne epoxy resin (SWEP) was synthesized by a chemical reaction between the epoxy resin and titanium diisopropoxide bisacetylacetonate in water. The structural characterizations via Fourier transform infrared spectroscopy and 13C nuclear magnetic resonance spectrsocopy confirmed the successful preparation of the SWEP resin. Differential scanning calorimetry and thermogravimetric analysis showed that the SWEP resin could be cured by heating without the use of any curing agents, and the cured coating exhibited good thermal resistance. The mechanical properties of the cured coatings were discussed in the context of the corresponding standards. The results confirmed that the physical properties of the SWEP coating were as good as those of a traditional two-component waterborne epoxy resin (DCWEP) coating. The chemical resistance analysis revealed that the water, acid and alkaline resistances of the SWEP coating all have significant improvements compared to those of the DCWEP coating. The electrochemical impedance spectroscopy and potentiodynamic polarization test implied that the SWEP coating provided better corrosion protection for metal substances than the DCWEP coating.

materials science, coatings & films,chemistry, applied
A high corrosion-resistant waterborne epoxy resin coating improved by addition of multi-interface structured zinc phosphate particles

Hu Cai,Xiteng Li,Yulin Zhang,Chao Yang,Suihan Cui,Liyuan Sheng,Daokui Xu,Ricky K.Y. Fu,Xiubo Tian,Paul K. Chu,Zhongzhen Wu

DOI: https://doi.org/10.1016/j.jmrt.2023.09.109

IF: 6.267

2023-09-20

Journal of Materials Research and Technology

Abstract:In the present study, a three-dimensional multi-interface structured zinc phosphate particle with large specific surface area was prepared by regulating the zinc phosphate crystal growth process, which was applied to develop a waterborne epoxy resin coating with better corrosion resistance. The results reveal that the multi-interface structured zinc phosphate particles could well coalesce with epoxy resin. Compared with the waterborne coating doped with and without two-dimensional zinc phosphate sheets, the multi-interface structured zinc phosphate particles doped waterborne epoxy resin coating has highest corrosion potential, lowest corrosion current density and the highest low-frequency impedance, which indicates the obvious benefits of multi-interface structured zinc phosphate particles on corrosion resistance. Moreover, the electrochemical properties tests on the waterborne epoxy resin coatings immersed in salt solution for 3000 h demonstrate that the multi-interface structured zinc phosphate particles doped waterborne epoxy resin coating almost has no changes but the other waterborne epoxy resin coatings decrease obviously. The surface characterization on the corroded waterborne epoxy resin coatings reveal that the multi-interface structured zinc phosphate particles doped waterborne epoxy resin coating possesses the relative integrated surface, while the inner corrosion has occurred in other coatings. The waterborne epoxy resin coatings with different additives sprayed on Al alloy surface could obtain the adhesion strength between 6.21 and 6.81 MPa, and the multi-interface structured zinc phosphate particles doped waterborne epoxy resin coating possesses the maximum value. Even after the salt solution immersion for 3000 hours, the multi-interface structured zinc phosphate particles doped waterborne epoxy resin coating still remains the adhesion strength above 6.21 MPa. Such excellent corrosion resistance should be ascribed to the cooperation of strengthened physical inhibition effect, decreased polar channel and complexation reaction by multi-interface structured zinc phosphate particles.

materials science, multidisciplinary,metallurgy & metallurgical engineering
APTES Modification of Molybdenum Disulfide to Improve the Corrosion Resistance of Waterborne Epoxy Coating

Yang Liu,Shihong Zhang,Yi He,Chunlin Chen,Chen Zhang,Peng Xie,Fei Zhong,Hongjie Li,Jingyu Chen,Zhenyu Li

DOI: https://doi.org/10.3390/coatings11020178

IF: 3.236

2021-02-02

Coatings

Abstract:MoS2 has been regarded as a promising addition for the preparation of epoxy-based coatings with high anticorrosion ability. However, its dispersion and compatibility remain significant challenges. In the present work, an organic thin layer was well coated on lamellar molybdenum disulfide (MoS2) via a simple modification of 3-aminopropyltriethoxysilane (APTES). The modification of hydrolyzing APTES on lamellar MoS2 effectively improved the dispersity of MoS2 in water-borne epoxy (WEP) and successfully enhanced the compatibility and crosslinking density of MoS2 with WEP. The influence of introducing MoS2-APTES into WEP coating on anticorrosion property for N80 steel was tested by electrochemical impedance spectroscopy (EIS), potentiodynamic polarization and salt spray test. The results exhibited that the |Z|0.01Hz value of MoS2-APTES/WEP still reached 3.647 × 107 Ω·cm2 even after the immersion time of 50 days in 3.5 wt.% NaCl solution, showing an extraordinary performance of corrosion resistance. The enhanced anticorrosion performance of composite coating could be resulted from the apparently increased dispersibility and compatibility of MoS2 in WEP.

materials science, multidisciplinary,physics, applied, coatings & films
Improvement in Corrosion Resistance and Mechanical Properties of Epoxy Coatings on Steel with the Addition of Thiadiazole Treated ZrC

Joseph Raj Xavier,Xavier, Joseph Raj

DOI: https://doi.org/10.1007/s11665-022-07387-y

IF: 2.3

2022-10-04

Journal of Materials Engineering and Performance

Abstract:Polymeric coatings have long been utilized in the shipping industry to protect the metallic equipment against corrosion. Multifunctional 2-amino-5-(methylthio)-1,3,4-thiadiazole (AMTTD) modified with zirconium carbide (ZrC) (AMTTD/ZrC) nanoparticles were synthesized by solution intercalation method, and the influence of adding AMTTD/ZrC nanoparticles within neat epoxy (EP) coating on steel structures was investigated for its hydrophobic, mechanical, and electrochemical properties in seawater. The electrochemical impedance spectroscopy and scanning electrochemical microscopy (SECM) techniques were utilized to investigate the protective properties of the investigated coatings. The coating resistance of the EP-AMTTD/ZrC-coated steel was found to be 6096.79 kΩ cm 2 even after 360 h of exposure to seawater. The coating resistance of EP-AMTTD/ZrC nanocomposite is found to be more than 40% greater than that of EP coating. In comparison to EP-coated steel (19.8 nA), the corrosion current density of EP-AMTTD/ZrC composite-coated steel generated by SECM method was 1.8 nA. The surface morphological studies such as field emission-scanning electron microscopy with energy-dispersive x-ray spectroscopy (FE-SEM/EDX), and x-ray diffraction analysis were carried out to examine the nature of the corrosion products. The water repellent property of the coatings was characterized by water contact angle (WCA) measurement. The newly developed EP-AMTTD/ZrC nanocomposite coating had increased hydrophobic characteristics (WCA: 143°). The adhesion strength of EP- AMTTD/ZrC nanocomposite coatings is found to be 13.2 MPa. Therefore, the compatibility of EP, AMTTD, and ZrC nanoparticles was established by superior hydrophobicity and improved corrosion protection and enhanced mechanical properties. Thus, the EP-AMTTD/ZrC nanocomposite coating could be employed as the vital coating materials in a variety of industrial applications.

materials science, multidisciplinary
Ti3C2Tx@CNF nanohybrid improving the corrosion resistance of waterborne epoxy coating under 15 MPa alternating hydrostatic pressure

Yangmin Wu,Wenjie Zhao,Sheng Liu,Liping Wang

DOI: https://doi.org/10.1016/j.cej.2022.135483

IF: 15.1

2022-06-01

Chemical Engineering Journal

Abstract:Cellulose nanofiber was grafted on Ti3C2Tx (Ti3C2Tx@CNF) and then Ti3C2Tx@CNF nanohybrid acted as nanofiller to endow epoxy coating superior barrier property. Electrochemical tests and corrosion products revealed that incorporation of Ti3C2Tx@CNF into epoxy could significantly improve its anti-corrosion performance. Even immersion in marine alternating hydrostatic pressure (AHP) environment for 240 h, the impedance modulus of composite coating was one order of magnitude higher as compared with controlled samples. Besides, cross-sectional structure confirmed that Ti3C2Tx@CNF remarkable improve the compactness of coating and thus conferring active adhesion strength with twice higher than that of pure epoxy after 240 h immersion in AHP.

engineering, chemical, environmental
Effect of GO‐TiO2 to waterborne epoxy resin on microstructure and anti‐corrosion properties

Tao Wan,Bo Wang,Shicheng Wei,Kailun Yu,Yujiang Wang,Yi Liang,Wei Huang,Hao Chen,Zhongyuan Jiao

DOI: https://doi.org/10.1002/app.54494

IF: 3

2023-08-05

Journal of Applied Polymer Science

Abstract:Diagram of preparation of GO‐TiO2 coatings and protection mechanism. To enhance the anti‐corrosion of the waterborne epoxy resin coating, we filled GO‐TiO2 into the coating with ultrasound and stirring method. Results show that coatings rendered optimum properties at GO‐TiO2 content of 0.4 wt% with a hardness of 3H and rate of thermal weight loss reduce 8.3 wt%. After immersion for 30 days, coating exhibited water absorption ratio of merely 11.25% and open circuit potential of −0.871 V. After 1000 h of scratch‐neutral salt spray test, no obvious signs of corrosion were observed on surface. Moreover, Electrochemical results demonstrated that maximum impedance modulus of 0.4GO‐TiO2 coating was 2.18 × 106 Ω cm2, corresponding to superior corrosion resistance. What is more, anticorrosion mechanism was discussed. In conclusion, Filling GO‐TiO2 improved mechanical properties, thermal stability and corrosion resistance of waterborne epoxy resin coatings.

polymer science
Preparation of zirconia-modified epoxy acrylate emulsion and its application in waterborne anticorrosion coating

Shaoxiang Li,Xin Zhang,Wenjuan Qu,Lijie Wang,Houwei Li,Jiaxin Liu,

DOI: https://doi.org/10.20964/2022.01.10

IF: 1.541

2022-01-01

International Journal of Electrochemical Science

Abstract:Zirconia-modified epoxy acrylate emulsion was synthesized via soap-free emulsion polymerization by adding different amounts of modified ZrO2 nanoparticles. The modified ZrO2 nanoparticles were characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction spectroscopy (XRD) and scanning electron microscopy (SEM). Thermogravimetric analysis (TGA) indicated that the addition of modified ZrO2 could improve the thermal stability of the films formed by the emulsions. Moreover, the electrochemical impedance spectra (EIS) results showed that the film former of zirconia-modified epoxy acrylate emulsion could effectively improve the corrosion resistance of the coatings. The results showed that the emulsion containing 1% modified ZrO2 had the best thermal stability and the corresponding coating had the best corrosion resistance.

electrochemistry
Preparation and Anticorrosive Performance of Waterborne Epoxy Resin Composite Coating with Amino-Modified Graphene Oxide

Ding Nan,Xin Li,Dongsheng Li,Qiong Liu,Biao Wang,Xin Gao,Ting Ma,Na He,Yu Xu,Junhui Dong

DOI: https://doi.org/10.3390/polym15010027

IF: 5

2022-12-22

Polymers

Abstract:A waterborne epoxy coating with superior corrosion resistance was developed by using a novel amino-functionalized graphene oxide (GO) that was modified by 2,5-diaminobenzenesulfonic acid. A battery of characterization methods, such as Fourier transform infrared spectroscopy (FT-IR), Raman spectra, X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM), was used to prove that DGO was successfully prepared by grafting the amino of 2,5-diaminobenzenesulfonic on GO. The results indicated that the surface of DGO became rougher than GO, but a complete sheet structure was still maintained after modification; the optimal modified GO could be achieved when the mass ratio of 2,5-diaminobenzenesulfonic acid and GO was 5:1. The electrochemical impedance spectroscopy (EIS) tests indicated that the impedance at 0.01 Hz of a coating with 0.2 wt.% DGO still remained at a relatively high value after immersion for 48 h in 3.5 wt.% NaCl, which was about one order higher than a pure waterborne epoxy resin coating, and the corrosion current density decreased from 3.76 × 10−11 A/cm2 to 3.62 × 10−12 A/cm2. The dry adhesion and wet adhesion increased to 1.90 and 1.22 MPa, respectively, and the adhesion loss decreased from 53% to 36%. These interesting features could make waterborne epoxy coatings a promising anticorrosion coating for metal in long-term protection.

polymer science
Influence of TiO 2 -MWCNTs nanohybrid material on the corrosion resistance of epoxy low-zinc coatings

Yongrun Li,Meiping Wu,Yiyao Wang,Jianyu Wang,Jiaqi Huang,Chenyu Wang,Wentao Wei,Yiwen Chen,Xiaojin Miao

DOI: https://doi.org/10.1016/j.colsurfa.2024.135326

IF: 5.518

2024-09-23

Colloids and Surfaces A Physicochemical and Engineering Aspects

Abstract:Aiming to improve the corrosion resistance of epoxy low-zinc coatings in marine environments, TiO 2 -MWCNTs nano-hybridized materials were prepared by sol-gel method in this study, and different contents of reinforcing phases were implanted as to improve the anticorrosive properties of epoxy low-zinc coatings. Characterization of the microscopic morphology, physical phase composition and chemical structure of the TiO 2 -MWCNTs materials demonstrated that the TiO 2 hybridization was successful and the loading of TiO 2 improved the dispersion of MWCNTs. To investigate the effect of the additive reinforcing phase on the mechanical and corrosion resistance of the coatings by characterizing the coating microscopic morphology, surface wettability, substrate adhesion, and impedance changes at different immersion times. The above results demonstrated that the epoxy composite coating had lower surface energy and 16 % larger surface contact angle compared with the pure epoxy low-zinc coating; the 0.4 wt% TiO 2 -MWCNTs/epoxy composite coating had the highest adhesion of 6.52 MPa. The electrochemical test results indicated that the TiO 2 -MWCNTs/epoxy low-zinc composite coating had the largest self-corrosion potential, the smallest self-corrosion current density of 4.538 μA/cm 2 , and the largest impedance of 242.3 KΩ/cm 2 . The addition of TiO 2 -MWCNTs reinforcing phase significantly extended the barrier protection time of the epoxy low zinc coating and maintained good corrosion resistance throughout the immersion cycle.

chemistry, physical
Improvement of the Tribological Properties and Corrosion Resistance of Epoxy–PTFE Composite Coating by Nanoparticle Modification

Lixia Ying,Yunlong Wu,Chongyang Nie,Chunxi Wu,Guixiang Wang

DOI: https://doi.org/10.3390/coatings11010010

IF: 3.236

2020-12-24

Coatings

Abstract:In order to meet the requirements of high corrosion resistance, wear resistance, and self-lubrication of composite coatings for marine applications, epoxy matrix composite coatings containing PTFE and TiO2 nanoparticles were prepared on the steel substrate. With silane coupling agent KH570 (CH2=C(CH3)COOC3H6Si(OCH3)3), titanium dioxide nanoparticles were modified, and organic functional groups were grafted on their surface to improve their dispersion and interface compatibility in the epoxy matrix. Then, the section morphology, tribological, and anticorrosion properties of prepared coatings, including pure epoxy, epoxy–PTFE, and the composite coating with unmodified and modified TiO2, respectively, were fully characterized by scanning electron microscopy, friction–abrasion testing machine, and an electrochemical workstation. The analytical results show that the modified TiO2 nanoparticles are able to improve the epoxy–PTFE composite coating’s mechanical properties of epoxy–PTFE composite coating including section toughness, hardness, and binding force. With the synergistic action of the friction reduction of PTFE and dispersion enhancement of TiO2 nanoparticles, the dry friction coefficient decreases by more than 73%. Simultaneously, modified titanium dioxide will not have much influence on the water contact angles of the coating. A larger water contact angle and uniform and compact microstructure make the composite coating incorporated modified TiO2 nanoparticles show excellent anti-corrosion ability, which has the minimum corrosion current density of 1.688 × 10−7 A·cm−2.

materials science, multidisciplinary,physics, applied, coatings & films
Modification of Hydrotalcite Loading Tannic Acid with Organic Silane and Application in Anticorrosive Epoxy Coating

Bui Minh Quy,Nguyen Thuy Chinh,Nguyen Thi Kim Anh,Vu Thi Tuyet,Nguyen Xuan Thai,Vu Quoc Trung,Ngo Thi Cam Quyen,Nguyen Ngoc Tan,Thai Hoang

DOI: https://doi.org/10.1002/open.202400120

ChemistryOpen

Abstract:Metal corrosion is a challenge for the world with heavy impacts on the economy. Study on the development of effectiveness anticorrosion additives is a promising strategery for the protection industry. This research focuses on the modification of hydrotalcite Mg-Al (HT) loading tannic acid (TA) with 3-(trimethoxy silyl) propyl methacrylate organo-silane (TMSPM) for applicating as an anti-corrosion additive for epoxy coating on the steel substrate. The suitable ratio of HT and modifiers was investigated and the suitable content of modified HT in epoxy matrix was found based on mechanical properties of the epoxy-based coating. The characteristics of modified HT were assessed through infrared (IR) spectroscopy, X-ray diffraction pattern (XRD), scanning electron microscopy (SEM), thermal gravimetry analysis (TGA), water contact angle (WCA), dynamic light scattering (DLS). Detailly, HT-TA3-S3 shows good stability in distilled water when HT/TA was modified with TMSPM which makes Zeta potential decreases significantly. Besides, SEM analysis presented HT-TA-S has a cylindrical shape about of 500 nm. Moreover, the crystallite size of HT/TA after being modified by TMSPM decreases sharply. All of these prove successfully synthesize HT loading TA with modified TMSPM. Water contact angle (WCA) decreases in case of loading TA and increases in case of modifying with TMSPM (WCA changed from HT (116.3°) to HT-TA (102.4°) and HT-TA-S (120.1°) which indicates the increased hydrophobicity of the sample. The obtained results showed HT/TA was modified successfully with TMSPM. The modification affected the size distribution and surface properties of HT nanoparticles while it did not impact on the crystal structure of HT. After incorporating modified HT/TA into the epoxy coating, the adhesion of coating to steel substrate was improved significantly. Consequently, the adhesion of epoxy/3 wt. % modified HT/TA coating was increased 3 times as compared to epoxy neat (from 0.76 MPa to 2.77 MPa). In addition, the relative hardness and gloss retention of epoxy/3 wt. % modified HT/TA coating reached the maximum values as compared to the others. Owing to salt spraying results, the epoxy/3 wt. % modified HT/TA exhibited an excellent anticorrosion ability for the steel substrate. All the above results show the potential of HT nanoparticles loading TA modified with TMSPM as anticorrosive additives for protective coatings on steel substrates.
Preparation of Environmentally Friendly Anticorrosive Coatings with Aniline Trimer-Modified Waterborne Polyurethane

Shaoxiong Xu,Xiaoying Dong,Yufei Zhao,Jinhui Han,Yanbing Ji,Run Kuang,Suhang Zhang,Sude Ma

DOI: https://doi.org/10.3390/coatings14111380

IF: 3.236

2024-10-31

Coatings

Abstract:Eco-friendly waterborne coatings frequently exhibit poor corrosion resistance, high solvent content, and extended curing times, attributed to the excessive employment of hydrophilic groups and petroleum-derived polyols. In this work, aniline trimer (ACAT) and polyethylene glycol (PEG) were used as chain extenders. E-44 epoxy resin was subsequently utilized to modify the system and an aniline trimer-modified waterborne polyurethane (AT-WPU) dispersion was prepared and characterized. The chemical structure of the synthesized ACAT was characterized employing 1H NMR, ESI-MS, and FTIR spectroscopy. The structure and coating performance of the AT-WPU dispersion were investigated utilizing FTIR, particle size analysis, thermogravimetric analysis, DSC, TEM, SEM, and electrochemical corrosion testing. The results demonstrate that the aniline trimer-modified waterborne polyurethane dispersion was successfully synthesized. Additionally, the DSC analysis results and thermogravimetric graphs indicate that the glass transition temperature and thermal stability of the coatings increased with the addition of aniline trimer. As the aniline trimer content increased, the hardness and adhesion of the coatings were significantly enhanced. In the electrochemical corrosion assessment, the corrosion current density of AT-WPU-3 attained 7.245 × 10−9 A·cm−2, and the corrosion rate was as low as 0.08 μm·Y−1, indicating excellent corrosion resistance. The present study provides promising practical applications in the domain of metal material protection.

materials science, multidisciplinary,physics, applied, coatings & films
Exploring the corrosion resistance of epoxy coated steel by integrating mechanochemical synthesized 2D covalent organic framework

Wen Li,Xinyu Zhang,Chenyang Zhang,Meiyan Yu,Junfeng Ren,Wei Wang,Shougang Chen

DOI: https://doi.org/10.1016/j.porgcoat.2021.106299

IF: 6.6

2021-08-01

Progress in Organic Coatings

Abstract:Organic anticorrosion coatings reinforced by 2D nanomaterials are attracting ever-increasing research interests due to their superior anticorrosion performances. However, the strong π-π and van der Waals (vdW) interactions make the conventional 2D nanomaterials difficult to realize homogenous dispersion in the coatings during coating preparation. To remedy this problem, in this work, we introduced 2D covalent organic framework (2D−COF) in epoxy resin (EP) to synergistically realize high dispersion and improve the corrosion resistance of EP coated steel, where the 2D−COF (TpPa-1) was mechanochemically synthesized from 1,3,5-triformylphloroglucinol (Tp) and p-phenylenediamine (Pa-1). The results show that the TpPa-1 can achieve self-dispersion in EP. Further analyses reveal that the self-dispersion of TpPa-1 in EP stems from the reactions between the amino groups in TpPa-1 and epoxy groups in EP. Moreover, the prepared EP/TpPa-1 composite coating coated steel presents superior corrosion resistace compared with pure EP coating due to the good dispersion of TpPa-1. The superior anticorrosion mechanism of the coated steel is unraveled by combining experiments and molecular dynamics simulations. The results show that the added TpPa-1 can effectively improve the compactness of the composite coating. This will on one hand lead to the lower diffusion rate of corrosive media, and on the other hand, enhance the adhesion strength between the composite coating and substrate. This work can trigger further studies to perform reasonable design of 2D−COF, and therefore, new anticorrosion coatings with superior physical-mechanical properties can be obtained.

materials science, coatings & films,chemistry, applied
Negative outcome studies and the null hypothesis.

D. Reinhart

DOI: https://doi.org/10.1016/0952-8180(93)90035-D

IF: 9.375

1993-05-01

Journal of Clinical Anesthesia

Abstract:
Preparation and study of modified phytic acid/epoxy resin anti-corrosion coating

Jun-Jie Ju,Yang Wang,Ming-Hua Yu,Xin Sun,Wei-Li Li,Zheng-Bai Zhao

DOI: https://doi.org/10.1007/s00396-023-05183-1

IF: 2.4

2023-10-15

Colloid & Polymer Science

Abstract:The anti-corrosion improvement of epoxy-based (EP) coatings through an eco-fridendly way is significant to industrial development. Phytic acid (PA) is a kind of natural corrosion inhibitor, but its use to enhance the anti-corrosion of EP is challenging due to their poor compatilibility. This problem is addressed by the modification of PA in this paper. First, PA is grafted to ethylene glycol diglycidyl ether (EGDE) to obtain modified PA (PA-EGDE) by the catalysis of tetrabutylammonium bromide. Subsequently, PA-EGDE is added to EP to fabricate PA-EGDE/EP coatings. When the PA-EGDE loading is 5 wt%, the PA-EGDE/EP coating exhibits best mechanical and anti-corrosion properties. The peeling force and adhesion failure rate are 2.03 MPa and 45.6%, and the hardness, flexibility and shock resistance are 2H, 1 mm and 50 cm, respectively. The corresponding E corr value of PA-EGDE/EP coating is -0.620 eV, which is much higher than that of EP coating (-0.797 eV); the impedance modulus is 10 8 Ω·cm 2 after immersion in 3.5 wt% NaCl aqueous solution for 30 days, which is much bigger than that of EP coating (10 6 Ω·cm 2 ). Moreover, the anti-corrosion mechanism of PA in EP coating is thoroughly discussed.

polymer science,chemistry, physical
Preparation and Corrosion Resistance of ETEO Modified Graphene Oxide/Epoxy Resin Coating

Chunling Zhang,Xueyan Dai,Yingnan Wang,Guoen Sun,Peihong Li,Lijie Qu,Yanlong Sui,Yanli Dou

DOI: https://doi.org/10.3390/coatings9010046

IF: 3.236

2019-01-15

Coatings

Abstract:Improving the corrosion resistance of epoxy resin coatings has become the focus of current research. This study focuses on synthesizing a functionalized silane coupling agent (2-(3,4-epoxycyclohexyl)ethyl triethoxysilane) to modify the surface of graphene oxide to address nanomaterial agglomeration and enhance the coating resistance of the epoxy resin coating to corrosion by filling the coating with functionalized graphene oxide. Functionalized graphene oxide and coatings filled with functionalized graphene oxide were characterized by Fourier transform infrared spectroscopy, X-ray diffraction, X-ray photoelectron spectroscopy, scanning electron microscopy, and transmission electron microscopy. The corrosion performance of each coating was studied by electrochemical impedance spectroscopy and a salt spray test. Results showed that the incorporation of functionalized graphene oxide enhances the corrosion protection performance of the epoxy composite coating, and the composite coating exhibited the best anticorrosion performance when the amount of functionalized graphene oxide was 0.7 wt %.

materials science, multidisciplinary,physics, applied, coatings & films
Phytic Acid Intercalated Graphene Oxide for Anticorrosive Reinforcement of Waterborne Epoxy Resin Coating

Na Wang,Huiying Gao,Jing Zhang,Ye Qin,Deyi Wang

DOI: https://doi.org/10.3390/polym11121950

IF: 5

2019-11-27

Polymers

Abstract:Epoxy resin coatings were prepared with phytic acid-doped graphene oxide (PA-GO) to modify epoxy resins (EP). The aim was to improve the dispersion of GO in waterborne epoxy resin, and thus to improve the corrosion resistance of steel structures. The Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS) results showed that PA-GO was successfully prepared and has a better dispersion in epoxy resin. This is mainly due to the PA insert, which increased the layer spacing of the GO. The results obtained under the controlled corrosive environment showed that the specimen coated with EP containing 1.0 wt.% PA-GO had better corrosion resistance than other samples. This resistance was also two orders of magnitude higher than pure epoxy coating. The main reason for this is that the dispersion of GO in waterborne epoxy resin had been improved.

polymer science

The ultimate properties of bone tissue: the effects of yielding.

Preparation of double linked waterborne epoxy resin coating using Titanium curing agent and aminopropyltriethoxysilane and its anticorrosive properties

Preparation and Properties of Waterborne Acrylic-Modified Epoxy Phosphate Resin and Its Coating

Tannic acid‐copper metal‐organic frameworks decorated graphene oxide for reinforcement of the corrosion protection of waterborne epoxy coatings

Corrosion resistance of a self-curing waterborne epoxy resin coating

A high corrosion-resistant waterborne epoxy resin coating improved by addition of multi-interface structured zinc phosphate particles

APTES Modification of Molybdenum Disulfide to Improve the Corrosion Resistance of Waterborne Epoxy Coating

Improvement in Corrosion Resistance and Mechanical Properties of Epoxy Coatings on Steel with the Addition of Thiadiazole Treated ZrC

Ti3C2Tx@CNF nanohybrid improving the corrosion resistance of waterborne epoxy coating under 15 MPa alternating hydrostatic pressure

Effect of GO‐TiO2 to waterborne epoxy resin on microstructure and anti‐corrosion properties

Preparation of zirconia-modified epoxy acrylate emulsion and its application in waterborne anticorrosion coating

Preparation and Anticorrosive Performance of Waterborne Epoxy Resin Composite Coating with Amino-Modified Graphene Oxide

Influence of TiO 2 -MWCNTs nanohybrid material on the corrosion resistance of epoxy low-zinc coatings

Improvement of the Tribological Properties and Corrosion Resistance of Epoxy–PTFE Composite Coating by Nanoparticle Modification

Modification of Hydrotalcite Loading Tannic Acid with Organic Silane and Application in Anticorrosive Epoxy Coating

Preparation of Environmentally Friendly Anticorrosive Coatings with Aniline Trimer-Modified Waterborne Polyurethane

Exploring the corrosion resistance of epoxy coated steel by integrating mechanochemical synthesized 2D covalent organic framework

Negative outcome studies and the null hypothesis.

Preparation and study of modified phytic acid/epoxy resin anti-corrosion coating

Preparation and Corrosion Resistance of ETEO Modified Graphene Oxide/Epoxy Resin Coating

Phytic Acid Intercalated Graphene Oxide for Anticorrosive Reinforcement of Waterborne Epoxy Resin Coating