Recovery knowledge and recovery-oriented services in Hong Kong.

W. Mak,B. Y. Lam,S. Yau

DOI: https://doi.org/10.1176/ps.2010.61.11.1164

2010-11-01

Psychiatric Services

Abstract:

What problem does this paper attempt to address?

Microstructure, Compressive Performance and Wear Resistance of Pure Molybdenum Additively Manufactured Via Laser Powder Bed Fusion

Guoliang Huang,Yong He,Shaojun Long,Qian Duan,Huan Chen,Xiaoqiang Peng,Liang Zhou,Ke Huang

DOI: https://doi.org/10.1016/j.ijrmhm.2024.106740

IF: 4.804

2024-01-01

International Journal of Refractory Metals and Hard Materials

Abstract:Pure molybdenum (Mo) additively manufactured via laser powder bed fusion is challenging due to its high laser reflectivity and sensitivity to cracking. To achieve crack-free pure Mo alloy and enhance production efficiency, this study employs a high-power (350 W) printing process with a layer thickness of 30 mu m, resulting in the successful fabrication of pure Mo with a relative density of 99.2%. X-ray diffraction (XRD) and electron backscatter diffraction (EBSD) revealed that the pure Mo specimens prepared by LPBF process exhibited different preferential grain orientations and lattice distortions in various building directions, with higher texture strength on the XOZ plane and greater lattice distortion on the XOY plane. The hardness of the pure Mo specimens reached 208 HV, with uniaxial compressive strength and elongation at 535 MPa and 20.9%, respectively, surpassing existing literature values by 37.2% and 8.0%. Furthermore, the dry friction behavior and mechanism of LPBF-manufactured pure molybdenum were investigated for the first time and compared to traditional powder metallurgy. Consequently, this research offers valuable insights for manufacturing crack-free LPBF pure molybdenum components with 30 mu m layer thickness, boasting superior mechanical and wear resistance.
In Situ Prediction of Microstructure and Mechanical Properties in Laser-Remelted Al-Si Alloys: Towards Enhanced Additive Manufacturing

Metin Kayitmazbatir,Mihaela Banu

DOI: https://doi.org/10.3390/ma17143622

2024-07-22

Abstract:Laser surface remelting of aluminum alloys has emerged as a promising technique to enhance mechanical properties through refined microstructures. This process involves rapid cooling rates ranging from 103 to 108 °C/s, which increase solid solubility within aluminum alloys, shifting their eutectic composition to a larger value of silicon content. Consequently, the resulting microstructure combines a strengthened aluminum matrix with silicon fibers. This study focuses on the laser scanning of Al-Si aluminum alloy to reduce the size of aluminum matrix spacings and transform fibrous silicon particles from micrometer to nanometer dimensions. Analysis revealed that the eutectic structure contained 17.55% silicon by weight, surpassing the equilibrium eutectic composition of 12.6% silicon. Microstructure dimensions within the molten zones, termed 'melt pools', were extensively examined using Scanning Electron Microscopy (SEM) at intervals of approximately 20 μm from the surface. A notable increase in hardness, exceeding 50% compared to the base plate, was observed in the melt pool regions. Thus, it is exemplified that laser surface remelting introduces a novel strengthening mechanism in the alloy. Moreover, this study develops an in situ method for predicting melt pool properties and dimensions. A predictive model is proposed, correlating energy density and spectral signals emitted during laser remelting with mechanical properties and melt pool dimensions. This method significantly reduces characterization time from days to seconds, offering a streamlined approach for future studies in additive manufacturing.
Additively Manufactured Al/SiC Cylindrical Structures by Laser Metal Deposition

Ainhoa Riquelme,Pilar Rodrigo,María Dolores Escalera-Rodríguez,Joaquín Rams

DOI: https://doi.org/10.3390/ma13153331

2020-07-27

Abstract:Preliminary characterization of the microstructure of Al/SiCp composites prepared by Laser Metal Deposition (LMD) was analyzed, and the microhardness and wear behavior of the materials manufactured have been evaluated. It has been determined that the combined effect of the laser speed and power is decisive for the fabrication process. The microstructure characterization shows that the presence of hygroscopic Al4C3 can be avoided by adding Ti to the composite matrix. The wear behavior of the LMD samples and their microhardness have been compared with Powder Metallurgy samples with the same composition. The LMD samples showed higher hardness and wear resistance.
Laser powder bed fusion of Mo2C/Ti-6Al-4V composites with alternately laminated α′/β phases for enhanced mechanical properties

Chao Cai,Jasper Chua Dong Qiu,Tey Wei Shian,Changjun Han,Tong Liu,Ling Bing Kong,Narasimalu Srikanth,Chen-Nan Sun,Kun Zhou

DOI: https://doi.org/10.1016/j.addma.2021.102134

IF: 11

2021-10-01

Additive Manufacturing

Abstract:Mo2C/Ti64 composites with nearly full densification and enhanced tensile strength were developed by using laser powder bed fusion (LPBF). The addition of 1–3 wt.% Mo2C particles with an average particle size of ~1 μm enabled the LPBF-printed composites with an alternately laminated α′-Ti/β-Ti microstructure along with Mo2C and in-situ synthesized M23C6 (M was Ti, Al, V, and Mo). During LPBF, most of the Mo2C particles were incorporated into the Ti64 matrix, resulting in the α′-Ti and β-Ti solid solutions. The segregation of Mo contributed to the generation of the β-Ti phase at the melt pool boundaries of the composites, leading to the alternating hard α′-Ti/soft β-Ti phases. Remarkable improvements of 22.8% and 19.5% in the hardness and tensile strength of the Ti64 matrix were achieved, respectively. The strengthening of the LPBF-printed composites was associated with the formation of the laminated α′-Ti/β-Ti structure, solid solution behavior of Mo and C, and presence of the remaining Mo2C and precipitated M23C6. The findings are anticipated to provide insights into the selection of reinforcement materials for additively manufactured composites with nearly full densities and greater mechanical strength.

engineering, manufacturing,materials science, multidisciplinary
Microstructure and Mechanical Properties of Selective Laser Melted Mg-9 Wt%al Powder Mixture

Xiaomiao Niu,Hongyao Shen,Jianzhong Fu

DOI: https://doi.org/10.1016/j.matlet.2018.03.068

IF: 3

2018-01-01

Materials Letters

Abstract:Selective laser melting (SLM) of Mg-Al powder mixture is a promising method to additively manufacture Mg-Al alloy components without using pre-alloyed powder as feedstock. However, the microstructure and consequent tensile properties of SLMed Mg-9 wt%Al powder mixture have not been systematically investigated. In this work, spherical Mg and Al powder with a weight ratio of 91:9 were mixed using ball milling and the mixture was SLMed at different processing parameters. Mg-Al alloy was successfully fabricated and the highest relative density achieved was 95.7%. The results of scanning electron microscopy showed that the microstructure and volume of defects could be controlled by tuning the processing parameters. The highest ultimate tensile strength achieved was 274 MPa, which was comparable to the strength of SLMed pre-alloyed Mg-9 wt%Al as reported in literature. Based on this study, SLM of different Mg powder mixture can be investigated in future. (C) 2018 Elsevier B.V. All rights reserved.
In-Situ Synthesis of Mosi2/Sic Composite Coating by Laser Cladding

S Yang,ML Zhong,WJ Liu,N Chen,QM Zhang

DOI: https://doi.org/10.1016/s0167-577x(03)00086-7

2001-01-01

Abstract:In order to improve resistance to high temperature and wear resistance of pure aluminum, the laser cladding experiments were conducted on a 3kW continuous wave CO2 laser to produce in-situ synthesized MoSi2/SiC composite coatings on pure aluminum. The laser consolidified microstructure and phase evolution were investigated using scanning electron micrograph and x-ray diffraction. The in-situ formation of MoSi2/SiC was conducted by adding a mixture of Mo, Si and C precursor powder layer followed by melting the layer and substrate under a laser beam. The experimental results showed that these compound, MoSi2 and SiC can be formed from three distinct powders of Mo, Si and C on Al alloy, provided that supplied energy was sufficient to start the reaction between the initial products, a good metallurgical bond between coating and the substrate can be achieved. The microstructures of the coating were composed of MoSi2, Mo5Si3 and SiC phases. The microhardness of coating was about twelve times that of the aluminum substrate, the maximum value reached HV(0.2)1200.
Comparative Study on the Surface Remelting of Mo-Si-B Alloys with Laser and Electron Beam

Qiuliang Li,Cheng Wang,Zhuoyue Li,Yi Qu,Xiangrong Li

DOI: https://doi.org/10.3390/ma15186223

2022-09-07

Abstract:The Mo-12Si-8.5B alloy was surface-remelted by laser and electron beam, and the microstructure of its melt pool and substrate regions were analyzed by scanning electron microscopy (SEM), X-ray diffraction (XRD), and energy spectrometry (EDS) techniques. It was found that the composition of the surface phases in the Mo-12Si-8.5B alloy did not change by the high-energy beam surface remelting process, but the microstructure of the molten pool region was significantly different from that of the substrate region, and its phase distribution was more uniform. Dendrites appeared on the surface of the material under the action of both processes, and the Si- and B-rich phases were mainly gathered in the interdendritic region. In the melt pool of the laser-remelted specimens, the α-Mo phase was continuously distributed with an average dendrite length of 70 µm, while the α-Mo phase distribution in the melt pool of the electron beam remelted specimens were relatively concentrated, with a larger dendrite size and an average dendrite length of 120 µm. The dendrite size in the melt pool of the laser remelted material was smaller, and the distribution of the elements was relatively uniform. Using a laser beam as the heat source was more favorable for the next step of the additive manufacturing of the core parts of hypersonic vehicles.
Selective laser melting of an advanced Al-Al2O3 nanocomposite

Quanquan Han

Abstract:Selective laser melting (SLM) has been widely used to manufacture customised metallic parts because it provides an integrated way to manufacture three-dimensional (3D) parts from computer-aided design models after several sub-processes. On the other hand, aluminium-based nanocomposites are widely used in the aerospace and automotive industries due to their light weight, high specific strength, excellent wear resistance, but their manufacturability and mechanical properties are not well understood when these new materials are employed in SLM. This is an important consideration because, compared with traditional manufacturing technologies, SLM offers the ability to manufacture engineering parts with very complex geometries by employing a layer-by-layer manufacturing principle. Hence, this thesis systematically studies the SLM of an advanced Al-Al2O3 nanocomposite that is synthesised using high-energy ball-milling (HEBM) process. The aim of this study is to use SLM to fabricate a nearly full dense Al-Al2O3 nanocomposite composed of 96 vol.% Al and 4 vol.% Al2O3 powder. The synthesis and characterisation of ball-milled powder is the first contribution of this study, which also investigates the influence of milling and pause duration on the fabrication of ball-milled composite powder. The second contribution of this work is the development of a 3D finite element model to predict the thermal behaviour of the first layer’s composite powder. Both the transient temperature distribution and molten pool dimensions are predicted within the laser scanning, which VI enables a more efficient selection of the process parameters (e.g. hatch spacing and scanning speed). The third contribution of this study is the optimisation of the SLM process parameters and microstructure investigation of the fabricated samples. The optimum laser energy density and scanning speed that are used to fabricate nearly full dense Al-Al2O3 nanocomposites are found to be 317.5 J/mm3 and 300 mm/s, respectively. The relative density is evaluated by quantifying the porosity on both the horizontal and vertical sections. The fabricated composite parts were observed to exhibit a very fine granular-dendrite microstructure due to the rapid cooling, while the thermal gradient at the molten pool region along the building direction was found to facilitate the formation of columnar grains. The final contribution of this study is the investigation of mechanical properties such as tensile strength, microhardness and macro and nanoscale wear behaviour. Compared to pure Al, the addition of 4 vol.% Al2O3 nanoparticulates was found to contribute to a 36.3% and 17.5% increase in the yield strength and microhardness of the composite samples, respectively. Cold working was found to contribute to a 39% increase in microhardness due to grain deformation. The pin-on-disc wear testing and atomic force microscopy (AFM) nanoscratching were performed to study the macro and nanoscale wear behaviour of the fabricated samples, respectively.

Materials Science,Engineering
Effects of remelting on the surface morphology, microstructure and mechanical properties of AlSi10Mg alloy fabricated by selective laser melting

Zezhou Kuai,Zhonghua Li,Bin Liu,Wenpeng Liu,Shuai Yang

DOI: https://doi.org/10.1016/j.matchemphys.2022.125901

IF: 4.778

2022-06-01

Materials Chemistry and Physics

Abstract:Selective laser melting (SLM) is an additive manufacturing technology that uses laser and metal powder to directly manufacture metal parts. The process has good mechanical properties and dimensional accuracy and can be put into use with a simple post-treatment. However, spheroidisation and warpage can easily occur in the forming process, resulting in poor surface quality and high porosity, which are the main limiting factors for the direct application of the parts formed using this technology. Laser remelting is an effective solution to solve these problems. In this research, the microstructure and mechanical properties of AlSi10Mg fabricated by laser remelting using two different scanning strategies were studied, and it was found that both the laser remelting methods can effectively improve the surface quality, reduce the surface roughness (2.3 μm, 4.0 μm) and porosity (0.08%, 0.2%), refine the grains size and improve the hardness. The thermal conductivity and reflectivity of the metal solidification layer are high, the spreading property of molten pool worsens and the width and depth of the molten pool decrease.

materials science, multidisciplinary
Laser Powder Bed Fusion of Oxidized Microscale SiC-particle-reinforced AlSi10Mg Matrix Composites: Microstructure, Porosity, and Mechanical Properties

Yan Chen,Yongming Ren,Kan Li,Bo Dang,Zengyun Jian

DOI: https://doi.org/10.1016/j.msea.2023.144860

IF: 6.044

2023-01-01

Materials Science and Engineering A

Abstract:Laser powder bed fusion (LPBF)-fabricated Al matrix composites reinforced with SiC particles are strongly influenced by SiC particle features. In this study, the microstructural features, mechanical properties, and porosity of moderate volume fraction (10 vol%) microscale SiC-particle-reinforced AlSi10Mg composites fabricated by LPBF under different oxidation temperatures of SiC particles were investigated. The results demonstrate that LPBF-deposited SiCp/AlSi10Mg composites mainly exhibited laser track segments in macroscale and fine cellular-like dendrite grains and (Al + Si) eutectic phases within the melt pool on a microscale. The transition layer of MgAl2O4 was present around the SiC particles in the oxidized-SiCp reinforced AlSi10Mg composites. In addition, the pore spatial distribution of the deposited composites using the microcomputed tomography test and the microstructural formation mechanism using Thermal Calc software were also studied. Using the finite element to model the deposited composites, it was found that the stress and strain distribution presented higher values than those without long-stripe precipitation phases in the deposited parts with long-stripe precipitation phases. The LPBF-fabricated oxidized-10 vol% SiCp/AlSi10Mg composite part with a relatively large ultimate tensile strength (-405.3 MPa), relative density (-98.89%), compressive strength (-1046 MPa) and friction coefficient (0.32) were obtained. In particular, the ultimate tensile strength was larger than that of the other reported SiCp/AlSi10Mg composites with similar volume fractions and particle sizes.
Selective Laser Melting to Manufacture “In Situ” Metal Matrix Composites: A Review

Sasan Dadbakhsh,Raya Mertens,Liang Hao,Jan Van Humbeeck,Jean‐Pierre Kruth

DOI: https://doi.org/10.1002/adem.201801244

IF: 3.6

2019-01-02

Advanced Engineering Materials

Abstract:After a brief introduction on selective laser melting (SLM) and “ex situ” manufacture of metal matrix composites (MMCs), this paper reviews the capacities and benefits of SLM to activate and control various “in situ” reactions during fabrication of 3D parts. It introduces several systems (such as Al/Fe2O3, AlSi10Mg/SiC, Al/ZnO, Ti/C, Ti/SiC, Ti/Si3N4, Ti/Mo2C, Fe/SiC, etc.) used to manufacture Al‐based, Ti‐based, and steel‐based “in situ” MMCs. Then, it illustrates the novel microstructural characteristics of these SLM‐made “in situ” MMCs for different cases, as they may appear from nano‐particles to nano‐whiskers and dendritic reinforcements homogeneously distributed in a metal matrix. It also focuses on SLM associated “in situ” mechanisms, explaining how an “in situ” reaction propagates based on “decomposition, diffusion, and reformation” and how the growth mechanisms turn into different morphologies such as rounded particles, whiskers, or polygonal block shapes. The influence of various SLM parameters (such as energy density, laser power/speed, powder layer thickness, and the size of initial powder particles) and the SLM “in situ” challenges are also discussed. This paper describes the advancements to manufacture metal matrix composites (MMCs) using selective laser melting (SLM) from reactive powders. Based on various metal‐based powder systems, it discusses how different novel microstructures and properties can appear in the “in situ” made MMCs. As an example, the shown figure illustrates the propagation of “in situ” products throughout an Al/Fe2O3 powder mixture.

materials science, multidisciplinary
Laser Powder Bed Fusion of SiO2/AlSi10Mg Composite Material

Zhijian Feng,Tian Yang,Yating Qiu,Wei Han,Lingbao Kong

DOI: https://doi.org/10.1016/j.ceramint.2024.11.329

IF: 5.532

2024-01-01

Ceramics International

Abstract:This study investigates the laser powder bed fusion (LPBF) process of SiO₂/AlSi10Mg composite material, focusing on the effects of AlSi10Mg powder addition on the laser melting of quartz glass. Composite and pure quartz powders were compared under LPBF conditions to evaluate the impact of varying AlSi10Mg weight percentages on the process. Results indicate that adding AlSi10Mg significantly enhances laser absorption and thermal conductivity, leading to improved melting of the quartz glass. With increasing AlSi10Mg content, bonding quality between the printed structure and the stainless steel substrate improves, though higher percentages (e.g., 12 wt%) introduce metal ball formation, which affects material uniformity. Optimal bonding and material distribution were achieved at 6 wt% AlSi10Mg. Additionally, the study examines the effects of different laser scanning strategies on LPBF outcomes, including surface morphology, density, and internal defects. These findings provide insights into optimizing LPBF parameters for composite materials, advancing the use of LPBF in fabricating glass-based composite structures.
In-situ synthesis of aluminum/nano-quasicrystalline Al-Fe-Cr composite by using selective laser melting

N. Kang,M. El Mansori,X. Lin,F. Guittonneau,H.L. Liao,W.D. Huang,C. Coddet

DOI: https://doi.org/10.1016/j.compositesb.2018.08.108

2018-12-01

Abstract:In this research, Al-Fe-Cr quasicrystal (QC) reinforced Al-based metal matrix composites were in-situ manufactured by using selective laser melting (SLM) from the powder mixture. The parametrical optimization based on our previous work was performed with focus on laser scanning speed. From the optimized parameters, an almost dense (99.7%) free-crack sample was fabricated with an ultra-fine microstructure. A phase transition from decagonal QC Al65Cu25Fe10Cr5 to icosahedral QC Al91Fe4Cr5 could be observed as laser scanning speed decreases. Differential scanning calorimetry curves show that the QC phase is quiet stable until 500 °C. And then, the effects of annealing temperature on the microstructural and mechanical properties were determined. The results indicate that the recrystallization and growth behavior of α-Al grains could be prevented by QC particle during annealing. Furthermore, the growth of QC particle, which tends to form a porous structure, leads an improvement of Young modulus and decline of ductility.
Microstructure and mechanical properties of an in-situ TiB2 particle reinforced AlSi10Mg composite additive manufactured by selective electron beam melting

Kaiwei Wu,Siming Ma,Xin Fang,Yang Li,Wenbin Kan,Haowei Wang,Mingliang Wang,Jun Liu,Zhe Chen

DOI: https://doi.org/10.1007/s10853-023-08516-1

IF: 4.5

2023-05-08

Journal of Materials Science

Abstract:Selective electron beam melting (SEBM) has been recently employed for additive manufacturing (AM) Al alloys but showing comparatively low hardness and strength. In this work, SEBM technique was employed to additive manufacture an in-situ TiB 2 particle reinforced AlSi10Mg composite. With optimized processing parameters, the SEBM TiB 2 /AlSi10Mg composite showed good surface quality and a high relative density. The as-printed composite exhibited a refined equiaxed grain structure with an average size of 27.7 μm. The eutectic Si phase was mostly spherical and uniformly distributed in the Al matrix, while the nano-sized TiB 2 particles were partly agglomerated. The resultant microstructure was associated with the combined effect of the rapid solidification and annealing-like process during SEBM. Additionally, TiB 2 particles facilitated grain refinement by enhancing the heterogeneous nucleation and retarding grain growth. The SEBM TiB 2 /AlSi10Mg composite presented a yield strength (YS) and ultimate tensile strength (UTS) of 103.6 MPa and 165.4 MPa, respectively, with an appreciable elongation of 15% at as-printed state. After a T6-like treatment, the YS and UTS of the composite were further improved to 225 MPa and 316 MPa, respectively, and an elongation of 12% was maintained. This paper shows the potency of SEBM in AM metal matrix composites (MMCs) with both agreeable strength and ductility.

materials science, multidisciplinary
Micromechanical Modeling of AlSi10Mg Processed by Laser-Based Additive Manufacturing: From as-Built to Heat-Treated Microstructures

Aravindh Nammalvar Raja Rajan,Marcel Krochmal,Thomas Wegener,Abhishek Biswas,Alexander Hartmaier,Thomas Niendorf,Ghazal Moeini

DOI: https://doi.org/10.3390/ma15165562

2022-08-13

Abstract:The unique microstructure of the alloy AlSi10Mg produced by the laser-based powder bed fusion of metals (PBF-LB/M) provides high-strength and high-strain-hardening capabilities of the material. The microstructure and mechanical properties of 3D-printed, i.e., additively manufactured, AlSi10Mg are significantly altered by post-building heat-treatment processes applied in order to tailor the final properties of the parts. Using an accurate computational model to predict and improve the mechanical performance of 3D-printed samples considering their microstructural features can accelerate their employment in envisaged applications. The present study aims to investigate the correlation between microstructural features and the mechanical behavior of as-built, direct-aged, and T6 heat-treated samples of PBF-LB/M AlSi10Mg under tensile loading using experiment and microstructure-sensitive modeling approaches. Nanoindentation tests are used to calibrate the parameters of the constitutive models for the Al and Si-rich phases. The experimental investigations revealed that heat treatment significantly changes the sub-grain morphology of the Si-rich phase, and this can have a considerable effect on the mechanical behavior of the components. The effect of the modeling of the Si-rich phase in the representative volume elements on the prediction of mechanical behavior is investigated using the J2 plasticity model. The combination of the crystal plasticity model for Al and the J2 plasticity model for the Si-rich phase is used to predict the tensile properties of the as-built and heat-treated states. The predicted results are in good agreement with the experimental results. This approach can be used to understand the microstructure-property relationship of PBF-LB/M AlSi10Mg and eventually tailor heat treatment for PBF-LB/M AlSi10Mg based on the requirement of the application.
Microstructure evolution and mechanical properties of Al-Al2O3 composites fabricated by selective laser melting

Jiubin Jue,Dongdong Gu,Kun Chang,Donghua Dai

DOI: https://doi.org/10.1016/j.powtec.2016.12.079

IF: 5.64

2017-04-01

Powder Technology

Abstract:The promising selective laser melting (SLM) technology was introduced to prepare Al based composites reinforced by Al2O3 particles. The influence of SLM processing parameters on the densification behavior, microstructure, microhardness and resultant wear performance was studied in detail. The results revealed that the near fully dense composite part (97.3% theoretical density) was achieved with the optimized v of 550mm/s applied. A proper decrease in the applied v to 550mm/s was proved feasible to favor the Al2O3 particle dispersion homogeneity due to the trapping effect of Al2O3 particle with the advancing interface in the molten pool. Besides, a continuous and compatible interface was developed in this case. At an even lower v of 450mm/s, the homogeneously dispersed Al2O3 reinforcements exhibited a novel ring structures along the boundaries of molten pool, but showing a significant coarsening morphology. The optimally prepared fully dense Al-Al2O3 composite part exhibited excellent hardness with a mean value of 175HV0.1 and superior wear performance with a considerably low coefficient of friction of 0.11 and a significantly reduced wear rate of 4.75×10−5mm3N−1m−1.

engineering, chemical
Selective laser melting (SLM) of AlSi12Mg lattice structures

Martin Leary,Maciej Mazur,Joe Elambasseril,Matthew McMillan,Thomas Chirent,Yingying Sun,Ma Qian,Mark Easton,Milan Brandt

DOI: https://doi.org/10.1016/j.matdes.2016.02.127

2016-05-01

Abstract:Additive manufacture (AM) enables innovative structural design, including the fabrication of complex lattice structures with unique engineering characteristics. In particular, selective laser melting (SLM) is an AM process that enables the manufacture of space filling lattice structures with exceptional load bearing efficiency and customisable stiffness. However, to commercialise SLM lattice structures it is necessary to formally define the manufacturability of candidate lattice geometries, and characterise the associated mechanical response including compressive strength and stiffness. This work provides an experimental investigation of the mechanical properties of SLM AlSi12Mg lattice structures for optimised process parameters as well as the manufacturability of lattice strut elements for a series of build inclinations and strut diameters. Based on identified manufacturability limits, lattice topologies of engineering relevance were fabricated, including both stretch-dominated and bending-dominated structures. Manufactured lattice morphology and surface roughness was quantified, as were the associated mechanical properties and deformation and failure behaviour.

materials science, multidisciplinary
In–situ synthesis of an Al composite reinforced with multi–scale Al12Mo, (Al, Zr, Si) and Al2O3 particles through a multi–stage reaction

Yihan Bian,Tong Gao,Zengqiang Li,Qianqian Sun,Xia Ma,Xiangfa Liu

DOI: https://doi.org/10.1016/j.msea.2019.138069

2019-08-01

Abstract:Heterogeneous strengthening effect has been a more and more attractive theory for designing metal matrix composites in recent years. In this paper, a new multiphase reinforced Al composite (Al12Mo+(Al,Zr,Si)+Al2O3)/Al has been prepared through a multi–stage reaction of Al–10ZrO2–5MoSi2 alloy on the basis of Al–10ZrO2, i.e. (ZrAl3+Al2O3)/Al composite, by introducing MoSi2. The strengthening phases, including micro–sized Al12Mo, sub–micron (Al,Zr,Si) and nano–sized Al2O3, are in–situ synthesized, performing attractive strengthening effect. The in–situ synthesized sub–micron (Al,Zr,Si) and nano–sized Al2O3 particles exhibit a net–work distribution, while micron Al12Mo particles act as the node of particle network. Compared with Al–10ZrO2, the Al–10ZrO2–5MoSi2 composite exhibits improved tensile strength at both room temperature (25 °C) and elevated temperature (350 °C). The reaction mechanism and phase evolution procedure have been discussed. This work can be referred in designing new multifarious particles reinforced composites to achieve promotion at material properties.
Selective laser melting of TiB2/AlSi10Mg composite: Processability, microstructure and fracture behavior

Zhe Feng,Hua Tan,Yanbo Fang,Xin Lin,Weidong Huang

DOI: https://doi.org/10.1016/j.jmatprotec.2021.117386

IF: 6.3

2022-01-01

Journal of Materials Processing Technology

Abstract:Recently aluminum matrix composites (AMCs) manufactured by selective laser melting (SLM) have attracted extensive attention in the lightweight application fields. In this work, pre-alloyed 6.5 wt.% TiB2/AlSi10Mg composite powder was initially densified via SLM. The result indicated that the material had a wide processing window, and the fully dense bulked samples were successfully fabricated when the laser volumetric energy density is 50∼70 J/mm3. We concluded that the morphology, size, and distribution of TiB2 particles in the as-deposited condition were generally consistent with those of the powder. The fine equiaxed microstructures without apparent anisotropy were remarkably realized. Therefore, a superior combination of excellent tensile strength and elongation was evident in the horizontal (∼536.9 MPa and ∼16.5%) and vertical (∼517.3 MPa and ∼15.4%) directions due to the systematic processing optimization, accompany with the strong work hardening capability. Its tensile properties are higher than that of the reported SLM-ed matrix alloy and other particle-reinforced Al-Si composites. Besides, the fracture behaviors were complicated, and the crack propagation paths were affected not only by the defect and eutectic Al-Si of the molten pool boundary (MPB) but also by the homogeneously distributed TiB2 particles. This study is expected to establish an important guiding significance for the practical engineering application of SLM-ed in-suit TiB2/AlSi10Mg composite.

materials science, multidisciplinary,engineering, manufacturing, industrial
Microstructure evolution and mechanical properties of selective laser melting fabricated hybrid particle reinforced AlSi10Mg composites

Xingyao Wang,Qinghua Lu,Peilei Zhang,Hua Yan,Haichuan Shi,Tianzhu Sun

DOI: https://doi.org/10.1016/j.matchar.2024.114483

IF: 4.537

2024-10-30

Materials Characterization

Abstract:(SiC+TiB 2 )/AlSi10Mg composite powders with 5 wt% micro-SiC particles and 1.5 wt% nano-TiB 2 particles were prepared by high energy ball milling, and hybrid particle reinforced aluminum matrix composites (AMCs) were fabricated by SLM. This study systematically investigated the effects of SiC and TiB 2 particles on the phase composition, microstructure evolution, grain crystallization, and mechanical properties. The machanisms of potential strengthening and fracture mechanisms were revealed. The tribological behaviors of the hybrid particle reinforced AlSi10Mg composites under different friction conditions were explored as well. The results show that the 1.5 wt% nano-TiB 2 particles provided sufficient nucleation sites for grain growth, completely transforming from coarse columnar to fined equiaxed grains. The average grain size decreases from 7.98 μm to 3.34 μm, and the texture is significantly weakened, which is beneficial to the homogenization of the microstructure, thereby improving the mechanical properties of the SiC/AlSi10Mg composites. The (SiC+TiB 2 )/AlSi10Mg composites showed a high ultimate tensile strength (∼ 489.1 MP), hardness (172.2 HV) and elongation of 8.2 %. The enhancement of mechanical properties was attributed to Orowan strengthening, fine grain strengthening, and load-bearing strengthening. Due to the Si precipitates and fine microstructure, a low wear rate of 0.50 × 10 −5 g/m was obtained, 10.7 % lower than that of SLM formed SiC/AlSi10Mg composites. The friction process is affected by abrasive wear, adhesive wear and delamination wear. It is aspired that the current approach can provide guidance for the design of new alloy systems with excellent performance.

materials science, multidisciplinary,metallurgy & metallurgical engineering, characterization & testing

Recovery knowledge and recovery-oriented services in Hong Kong.

Microstructure, Compressive Performance and Wear Resistance of Pure Molybdenum Additively Manufactured Via Laser Powder Bed Fusion

In Situ Prediction of Microstructure and Mechanical Properties in Laser-Remelted Al-Si Alloys: Towards Enhanced Additive Manufacturing

Additively Manufactured Al/SiC Cylindrical Structures by Laser Metal Deposition

Laser powder bed fusion of Mo2C/Ti-6Al-4V composites with alternately laminated α′/β phases for enhanced mechanical properties

Microstructure and Mechanical Properties of Selective Laser Melted Mg-9 Wt%al Powder Mixture

In-Situ Synthesis of Mosi2/Sic Composite Coating by Laser Cladding

Comparative Study on the Surface Remelting of Mo-Si-B Alloys with Laser and Electron Beam

Selective laser melting of an advanced Al-Al2O3 nanocomposite

Effects of remelting on the surface morphology, microstructure and mechanical properties of AlSi10Mg alloy fabricated by selective laser melting

Laser Powder Bed Fusion of Oxidized Microscale SiC-particle-reinforced AlSi10Mg Matrix Composites: Microstructure, Porosity, and Mechanical Properties

Selective Laser Melting to Manufacture “In Situ” Metal Matrix Composites: A Review

Laser Powder Bed Fusion of SiO2/AlSi10Mg Composite Material

In-situ synthesis of aluminum/nano-quasicrystalline Al-Fe-Cr composite by using selective laser melting

Microstructure and mechanical properties of an in-situ TiB2 particle reinforced AlSi10Mg composite additive manufactured by selective electron beam melting

Micromechanical Modeling of AlSi10Mg Processed by Laser-Based Additive Manufacturing: From as-Built to Heat-Treated Microstructures

Microstructure evolution and mechanical properties of Al-Al2O3 composites fabricated by selective laser melting

Selective laser melting (SLM) of AlSi12Mg lattice structures

In–situ synthesis of an Al composite reinforced with multi–scale Al12Mo, (Al, Zr, Si) and Al2O3 particles through a multi–stage reaction

Selective laser melting of TiB2/AlSi10Mg composite: Processability, microstructure and fracture behavior

Microstructure evolution and mechanical properties of selective laser melting fabricated hybrid particle reinforced AlSi10Mg composites