Abstract:Introduction Recent developments in synchrotron-based highpressure experiments have allowed us to investigate the nature of materials directly under the extreme highpressure and high-temperature conditions that exist within deep planetary interiors. By using the laserheating system available at the HP-CAT beamline at the APS and angle-dispersive x-ray microdiffraction, we have studied the melting properties of transition metals at high pressure. Melting under compression is an intriguing subject. It can be observed in a laser-heated diamond anvil cell (DAC) and in shock experiments. Also, many attempts have been made to theoretically predict the melting curves of different metals. Still today, these three methods yield very different results. Tantalum (Ta) and tungsten (W), two of the metals with the highest melting temperature ( Tm) at 1 bar, remain stable in the bcc structure up to megabar pressures. These two characteristics allow melting to be studied over a wide range of pressures without the complication of solid-solid structural transitions, thereby making Ta and W excellent candidates for improving the understanding of melting. Previous studies of the high-pressure melting of Ta showed large discrepancies (e.g., at 25 GPa, experiments observed Tm = 3500 ±100K, and theory predicts Tm = 4500K), which are summarized in Fig. 1. These disagreements, which include even the melting slope at 1 bar, emphasize the need for a precise experimental study of the melting behavior of transition metals under compression. Accurate measurements of the melting of Ta and W in a pressure-temperature (P-T) range up to 50 GPa and 4000K are reported on here. These reliable experiments were carried out at HP-CAT beamline station 16-ID-B. A small slope for the melting curve of Ta and W is estimated, and an explanation for this fact is given by assuming a vacancy model for the melting process.

Measurement of Melting Point, Normal Spectral Emittance (at Melting Point) and Electrical Resistivity (Near Melting Point) of Some Refractory Alloys

Thermal conductivity measurement of phase-change material near melting point based on perturbation method

Measuring the Refractive Index of Optical Adhesives at Cryogenic Temperatures.

Thermal Conductivity: V, High‐Temperature Method and Results for Alumina, Magnesia, and Beryllia from 1000° to 1800°C

Melting spectral emissivity measurement of metal during the melting and solidification process

Design of refractory intermetallic alloys based on γ'-phase with high melting temperature. Part 2

Measurements of the melting points, liquidus, and solidus of the Mo, Ta, and Mo Ta binary alloys using a novel high-speed pyrometric technique

Surface Tension Measurement of Metastable Liquid Ti–Al–Nb Alloys

High-Temperature Mechanical Properties of NbTaHfTiZrV0.5 Refractory High-Entropy Alloys

Mechanical properties of Nb25Mo25Ta25W25 and V20Nb20Mo20Ta20W20 refractory high entropy alloys

Spectral Emissivity of Technical Titanium near the Melting Point

Crystallization Behavior and Temperature Dependence of the Initial Permeability of an FeCuNbSiB Alloy

Specific Heat Measurement of Stable and Metastable Liquid Ti–Al Alloys

Compressive vs. tensile yield and fracture toughness behavior of a body-centered cubic refractory high-entropy superalloy Al 0.5 Nb 1.25 Ta 1.25 TiZr at temperatures from ambient to 1200°C

Ab initio inspection of thermophysical experiments for zirconium near melting

Elastic constants in Nb-Zr alloys from zero temperature to the melting point: Experiment and theory

Viscosity Measurement of Molten Alumina and Zirconia Using Aerodynamic Levitation, Laser Heating and Droplet Oscillation Techniques.

Laser Heating and X-ray Microdiffraction : A Powerful Tool to Study Melting of Metals at Extremely High Pressures and Temperatures

Microstructure and elevated temperature properties of a refractory TaNbHfZrTi alloy

The Thermal Conductivity of Near-Eutectic Galinstan (Ga68.4In21.5Sn10) Molten Alloy

Thermal Performance Determination of Binary Fe-Al Alloys at Elevated Temperatures