Abstract:The renewability and ease of processing of polylactide (PLA) make it ideal for disposable foam products. However, controlling the foam structure is challenging due to its low melt strength and crystallization ability, which can result in cell rupture-prone and excessively large cells, necessitating a comprehensive understanding of the influences of foaming parameters (temperature, pressure, and time) on cell structures and properties to unlock PLA’s full potential. This study optimizes the fabrication of PLA foams using solid-state batch foaming under supercritical CO2 conditions by employing a central composite design of response surface methodology. Single-parameter investigations reveal that higher foaming temperature, increased pressure, and longer foaming time increase the apparent density due to reduced polymer viscosity, pressure-dependent gas entrapment, and enhanced gas diffusion, leading to faster cell nucleation and cell formation. The compressive properties depend on stress-strain behavior and cell morphology, influenced by the cell shape and wall thickness. Thicker cell walls delay cell buckling and improve compression resistance. Higher sphericality evenly distributes compressive stress across cell surfaces, enhancing the foam’s resilience against localized collapse. Multi-response optimization successfully fabricated lightweight PLA foam (0.134 g/cc apparent density) with enhanced compressive modulus (1.955 MPa at 50% strain) and controlled cell morphology (average cell size of 21.055 μm and cell density of 52.385 × 105 cells/cm3) at optimized foaming conditions (180 °C, 165 bar, and 2.3 h). The PLA foams have potential as a reusable and degradable absorbent for liquids and oils, but there are challenges in scaling production.

A positive contact ball and ring implant for use after enucleation.

Thermal analysis of polylactic acid under high CO2 pressure applied in supercritical impregnation and foaming process design

Modulating Drug Release from Short Poly(ethylene Glycol) Block Initiated Poly(L-lactide) Di-block Copolymers

Study on the Foaming Behaviors of PBS and its Modification with PA6IcoT Assisted by scCO2

Supercritical CO2 impregnation of PLA/PCL films with natural substances for bacterial growth control in food packaging

Extruded polylactide bead foams using anhydrous supercritical CO2 extrusion foaming

Effect of Operational Variables on Supercritical Foaming of Caffeic Acid-Loaded Poly(lactic acid)/Poly(butylene adipate-co-terephthalate) Blends for the Development of Sustainable Materials

Polylactic Acid Chemical Foaming Assisted by Solid-State Processing: Solid-State Shear Pulverization and Cryogenic Milling

Microcellular Injection Molded Polylactic Acid/poly (Ε-Caprolactone) Blends with Supercritical CO2: Correlation Between Rheological Properties and Their Foaming Behavior

Fabrication of poly(lactic acid) foam with high expansion ratio and oriented cellular structure by restricting cold crystallization

Preparation of Cross-Linked Microparticles of Poly(glycidyl Methacrylate) by Dispersion Polymerization of Glycidyl Methacrylate Using a PDMS Macromonomer As Stabilizer in Supercritical Carbon Dioxide

Generation of Biocompatible PCL Foams by Supercritical Foaming

Controlled Foaming of Polycarbonate/polymethyl Methacrylate Thin Film with Supercritical Carbon Dioxide

Foaming of PCL-Based Composites Using scCO2: Structure and Physical Properties

Tuning pore size and density of rigid polylactic acid foams through thermally induced phase separation and optimization using response surface methodology

Development of Poly (Lactide Acid) Foams with Thermally Expandable Microspheres

Supercritical fluid and cocrystallization technologies for designing antimicrobial food packaging PLA nanocomposite foams loaded with eugenol cocrystals with prolonged release

Preparation and Density Control of Pmma Microcellular Foams Via Supercritical Carbon Dioxide Foaming

Multi-Response Optimization and Cell Structure-Property Relationships of Polylactide (PLA) Foams

Green Processing of Neat Poly(Lactic Acid) Using Carbon Dioxide under Elevated Pressure for Preparation of Advanced Materials: A Review (2012–2022)