Tuning pore size and density of rigid polylactic acid foams through thermally induced phase separation and optimization using response surface methodology

Morteza Ghorbandoust,Mohammad Fasihi,Reza Norouzbeigi

DOI: https://doi.org/10.1038/s41598-024-62958-4

IF: 4.6

2024-05-30

Scientific Reports

Abstract:Rigid polylactic acid (PLA) foams fabricated via thermally induced phase separation (TIPS) utilizing a ternary solution of PLA, Tetrahydrofuran (THF), and water. The PLA gels were stabilized mechanically by the substituting of the THF/water solvent mixture with ethanol as non-solvent and subsequently vacuum dried. A comprehensive characterization of PLA foams was achieved by Scanning Electron Microscopy (SEM), X-ray Diffractometry (XRD) and Brunauer–Emmett–Teller (BET) analyses. The BET area obtained in the PLA foam is up to 18.76 m 2 /g. The Response Surface Methodology (RSM) was utilized to assess the impacts of four independent variables (polymer concentration, solvent composition, quench temperature, and aging time) on the pore size and density of PLA foam. The experimental findings demonstrated that the fabrication parameters could be fine-tuned to govern the morphology of the pores, comprising their size and density. The optimal values of parameters for cell size were identified by RSM to be 8.96 (wt%), 91.60 (w/w), 5.50 °C, and 3.86 h for the optimum cell size of 37.96 μm (37.78 by Genetic Algorithm). Optimum density by RSM 88.88 mgr/cm 3 (88.38 mgr/cm 3 by Genetic Algorithm) was obtained at 5.00 (wt%), 89.33 (w/w), 14.40 °C and 2.65 h.

multidisciplinary sciences

What problem does this paper attempt to address?

The problem that this paper attempts to solve is how to adjust the pore size and density of polylactic acid (PLA) foam through thermally - induced phase separation (TIPS) technology. Specifically, the researchers optimized four independent variables (polymer concentration, solvent composition, quenching temperature, and aging time) by the response surface method (RSM) to control the pore size and density of PLA foam, thereby achieving effective regulation of the foam morphology. The objectives of the paper include:

1. **Study the influence of variables**: Explore the influence of polymer concentration, solvent composition, quenching temperature, and aging time on the pore size and density of PLA foam.
2. **Optimize parameters**: Use RSM to determine the best combination of process parameters to obtain the ideal pore size and density.
3. **Study the aging time for the first time**: Introduce the aging time as a variable in the solvent - exchange technology, filling the research gap in this field.
4. **Design an open - cell structure**: Design PLA foam with an open - cell structure by the TIPS method for separating and adsorbing substances such as oil - water mixtures, dyes, and heavy metals.

### Formula Explanation

The paper uses multiple formulas to describe experimental results and theoretical models. Here are several key formulas and their explanations:

1. **Linear relationship of predicted response**:
\[
R_x=\gamma_0+\sum_{i = 1}^{4}\gamma_i y_i+\sum_{i = 1}^{4}\gamma_{ii}y_i^2+\sum_{i = 1}^{3}\sum_{j = i + 1}^{4}\gamma_{ij}y_i y_j
\]
where \(R_x\) is the predicted response value, \(\gamma_0\) is the constant term, \(y_i\) and \(y_j\) are the levels of independent variables, and \(\gamma_i\), \(\gamma_{ii}\) and \(\gamma_{ij}\) are the coefficients of the linear, quadratic and interaction terms respectively.

2. **Specific volume calculation**:
\[
v_s=\frac{\rho_f}{\rho}
\]
where \(v_s\) is the specific volume, \(\rho_f\) is the density of PLA foam, and \(\rho\) is the density of PLA.

3. **Porosity calculation**:
\[
\epsilon = 1 - v_s
\]

4. **BET theoretical formula**:
\[
\frac{1}{\vartheta\left(\frac{P_0}{P}-1\right)}=\frac{C - 1}{C\vartheta_m}+\frac{1}{C\vartheta_m}
\]
where \(\vartheta\) is the adsorption amount, \(P_0\) is the saturated vapor pressure, \(P\) is the equilibrium pressure, \(\vartheta_m\) is the monolayer adsorption amount, and \(C\) is a constant related to the properties of the adsorbent.

### Summary

Through systematic research and optimization, this paper successfully controls the pore size and density of PLA foam, providing theoretical and technical support for the preparation of PLA foam with specific properties. These results not only help to improve the performance of PLA foam in various applications but also provide an important reference for future research.