Abstract:Surface coating is an effective strategy to suppress side reactions at the electrode/electrolyte interface and improve cycling stability of the Ni-rich LiNi x Co y Mn1- x - y O2 electrodes. It is difficult to prepare a complete coating layer on the secondary particles by traditional methods, due to the alkaline substances and oxidative property on surface. In this work, a coating process of Mg3B2O6 running counter to traditional routes was designed to modify LiNi0.8Co0.1Mn0.1O2 (NCM811) cathode material. In a weak polar ethanol medium, BH4 - ions are uniformly lain on particle surface by the interaction between its electronegativity and oxidizing surface, which also change the charge state into negative atmosphere around the NCM811 surface. Then Mg2+ ions are also completely dispersed by the mutual attraction between metal cations and the hydrolyzed BO3 -. Then a full surface coverage of Mg3B2O6 was prepared in situ on the NCM811 secondary particles. The complete coating layer protects the surface crystal structure of the NCM811 and limits the irreversible phase transition. The optimized composite with a suitable coverage of 1 % Mg3B2O6 exhibits enhanced rate capability and excellent cycling performance. At a high current density of 10C, it delivers a specific capacity of 162.7 mAh g−1. Especially, it maintains 160.6 mAh g−1 after 400 cycles at a high cut-off voltage of 4.5 V at 1C with a retention of 80.3 %. In addition, Mg3B2O6 is a non-toxic and non-polluting material. The simple coating process with low-cost raw materials as well as mild operating conditions endow this technology with potential practical application value.

Boosting cycle stability of NCM811 cathode material via 2D Mg-Al-LDO nanosheet coating for lithium-ion battery

Optimized structure stability and cycling performance of LiNi0.8Co0.1Mn0.1O2 through homogeneous nano-thickness Al2O3 coating

High structure stability and Li-conduction of LiNi0.8Co0.1Mn0.1O2 cathode co-coated by Al2O3 and LiNbO3 for high performance lithium-ion battery

Enhancing cyclic and in-air stability of Ni-Rich cathodes through perovskite oxide surface coating

Stabilization of NCM811 cathode for Li-ion batteries by N-doped carbon coating

Advancing Lithium-Ion Batteries' Electrochemical Performance: Ultrathin Alumina Coating on Li(Ni0.8Co0.1Mn0.1)O2 Cathode Materials

An Mg–Al dual doping strategy to enhance the structural stability and long cycle life of LiNi0.8Co0.1Mn0.1O2 cathode material

Enhanced High-Voltage Cycling Stability of Ni-rich LiNi0.8Co0.1Mn0.1O2 Cathode Coated with Li2O–2B2O3

Multifunctional Integration of Double-Shell Hybrid Nanostructure for Alleviating Surface Degradation of LiNi<sub>0.8</sub>Co<sub>0.1</sub>Mn<sub>0.1</sub>O<sub>2</sub> Cathode for Advanced Lithium-Ion Batteries at High Cutoff Voltage

Multifunctional Integration of Double-Shell Hybrid Nanostructure for Alleviating Surface Degradation of LiNi0.8Co0.1Mn0.1O2 Cathode for Advanced Lithium-Ion Batteries at High Cut-Off Voltage.

Elevating cycle stability of Ni-rich NCM811 cathode via single-crystallization integrating dual-modification strategy for lithium-ion batteries

Dual Functions of Three-Dimensional Hierarchical Architecture on Improving the Rate Capability and Cycle Performance of LiNi0.8Co0.1Mn0.1O2 Cathode Material for Lithium-Ion Battery

Fully coating of Mg3B2O6 in nonaqueous solution on Ni-rich LiNi0.8Co0.1Mn0.1O2 secondary particles to improve cycling stability of lithium-ion batteries

Carbonized Polymer Dots Enhancing Interface Stability of LiNi0.8Co0.1Mn0.1O2 Cathodes

Improving electrochemical performance of NCM811 cathodes for lithium-ion batteries via consistently arranging the hexagonal nanosheets with exposed {104} facets

Pre-Deoxidation of Layered Ni-Rich Cathodes to Construct a Stable Interface with Electrolyte for Long Cycling Life

Double Conductor Coating to Improve the Structural Stability and Electrochemical Performance of LiNi 0.8 Co 0.1 Mn 0.1 O 2 Cathode Material

A Novel Synthesis Strategy to Improve Cycle Stability of LiNi 0.8 Mn 0.1 Co 0.1 O 2 at High Cut-off Voltages Through Core-Shell Structuring

Superior Stability Secured by a Four-Phase Cathode Electrolyte Interface on a Ni-Rich Cathode for Lithium Ion Batteries

In-situ construction protective layer and phosphate doping synergistically improve the long-term cycle stability of LiNi0.6Co0.1Mn0.3O2

Al2O3 coated single-crystalline hexagonal nanosheets of LiNi0.6Co0.2Mn0.2O2 cathode materials for the high-performance lithium-ion batteries