Abstract:The Schockley–Quisser (SQ) limit of 28.64% is distant from the Sb 2 S 3 solar cells' record power conversion efficiency ( PCE ), which is 8.00%. Such poor efficiency is mostly owing to substantial interface-induced recombination losses caused by defects at the interfaces and misaligned energy levels. The endeavor of this study is to investigate an efficient Sb 2 S 3 solar cell structure via accurate analytical modeling. The proposed model considers different recombination mechanisms such as non-radiative recombination, Sb 2 S 3 /CdS interface recombination, Auger, SRH, tunneling-enhanced recombination, and their combined impact on solar cell performance. This model is verified against experimental work (Glass/ITO/CdS/Sb 2 S 3 /Au) where a good coincidence is achieved. Several parameters effects such as thickness, doping, electronic affinity, and bandgap are scrutinized. The effect of both bulk traps located in CdS and Sb 2 S 3 on the electrical outputs of the solar cell is analyzed thoroughly. Besides, a deep insight into the effect of interfacial traps on solar cell figures of merits is gained through shedding light into their relation with carriers' minority lifetime, diffusion length, and surface recombination velocity. Our research findings illuminate that the primary contributors to Sb 2 S 3 degradation are interfacial traps and series resistance. Furthermore, achieving optimal band alignment by fine-tuning the electron affinity of CdS to create a Spike-like conformation is crucial for enhancing the immunity of the device versus the interfacial traps. In our study, the optimized solar cell configuration (Glass/ITO/CdS/Sb 2 S 3 /Au) demonstrates remarkable performance, including a high short-circuit current ( J SC ) of 47.9 mA/cm 2 , an open-circuit voltage ( V OC ) of 1.16 V, a fill factor ( FF ) of 54%, and a notable improvement in conversion efficiency by approximately 30% compared to conventional solar cells. Beyond its superior performance, the optimized Sb 2 S 3 solar cell also exhibits enhanced reliability in mitigating interfacial traps at the CdS/Sb 2 S 3 junction. This improved reliability can be attributed to our precise control of band alignment and the fine-tuning of influencing parameters.

Numerical simulation of Sb2Se3-based solar cells

Numerical Simulation of the Performance of Sb2Se3 Solar Cell via Optimizing the Optoelectronic Properties Based SCAPS-1D

Analysis of Sb2Se3/CdS based photovoltaic cell: A numerical simulation approach

Towards high-efficiency planar heterojunction antimony sulfide solar cells

Exploring Sb2S3 as a hole transport layer for GeSe based solar cell: A numerical simulation

Concurrent investigation of antimony chalcogenide (Sb2Se3 and Sb2S3)-based solar cells with a potential WS2 electron transport layer

Carrier Transport Enhancement Mechanism in Highly Efficient Antimony Selenide Thin‐Film Solar Cell

An Optimization Path for Sb2(S,Se)3 Solar Cells to Achieve an Efficiency Exceeding 20

Rotational design of charge carrier transport layers for optimal antimony trisulfide solar cells and its integration in tandem devices

Crystal Growth Promotion and Defect Passivation by Hydrothermal and Selenized Deposition for Substrate-Structured Antimony Selenosulfide Solar Cells

Sb2Se3 thin film solar cells in substrate configuration and the back contact selenization

An effective engineering with simultaneous carrier density enhancement and interface optimization enables efficient Sb2Se3 solar cells

Numerical modeling of CuSbSe2-based dual-heterojunction thin film solar cell with CGS back surface layer

Interfacial Engineering Towards Enhanced Photovoltaic Performance of Sb2Se3 Solar Cell

Quasiepitaxy Strategy for Efficient Full‐Inorganic Sb2S3 Solar Cells

Scrutinizing transport phenomena and recombination mechanisms in thin film Sb2S3 solar cells

Numerical optimization of inorganic p-Sb2Se3/n-ZrS2 heterojunction solar cells: achieving high efficiency through SCAPS-1D simulation

Confined‐Space Selenium‐Assisted Tellurization Posttreatment Strategy for Efficient Full‐Inorganic Sb2S3 Thin‐Film Solar Cells

Quasiepitaxy Strategy for Efficient Full‐Inorganic Sb <sub>2</sub> S <sub>3</sub> Solar Cells

Heterojunction Lithiation Engineering and Diffusion-Induced Defects Passivation for Highly Efficient Sb2(S,Se)3 Solar Cells

Development of Antimony Sulfide–selenide Sb2(S, Se)3-based Solar Cells