Abstract:Lightweight refractory high-entropy alloy coatings (RHEAcs) of NbxMo$_{0.5}$Ti$_{1.5}$Ta$_{0.2}$Cr (where $x=$ 1, 1.3, 1.5, and 2) were fabricated on the surface of 316L stainless steel using laser cladding (LC) technology. A comprehensive study was conducted to elucidate the effect of Nb content on the microstructure, microhardness and wear resistance of NbxMo$_{0.5}$Ti$_{1.5}$Ta$_{0.2}$Cr RHEAcs before and after annealing at 900 for 10 h. The results show that the grains are gradually refined with the increase of Nb content. The coating consists mainly of a body-centered cubic (BCC) solid solution, C15-Laves phase, and a small amount of hexagonal close-packed (HCP) solid solution containing Ti. The microhardness of RHEAcs is significantly higher compared to the base material. Notably, at Nb1.3, due to the influence of lattice dislocations, the microhardness reaches a peak of 1066.5 HV, which is about 7.11 times higher than that of the base material. On the contrary, at Nb$_2$, the microhardness is at its lowest point, averaging 709.31 HV, but 4.72 times that of the base material. After annealing, an increase in microhardness is observed at all Nb concentrations, up to 31.2% at Nb$_2$. Before annealing, the wear resistance of RHEAcs was slightly better than that of 316L stainless steel at different Nb contents. However, after annealing, the coefficient of friction (COF) and wear rate of the coatings are lower than those of annealed 316L stainless steel, highlighting their excellent wear resistance. It is noteworthy that the loss of wear properties after annealing at Nb1 is at a minimum, obtaining the most balanced wear resistance before and after annealing. The enhanced wear resistance after annealing can be attributed to the presence of ultra-fine grain oxide friction layers, mainly composed of TiO2 and Ta2O5 . The main mode of wear is oxidative wear, with a small amount of wear from abrasive wear.

Microstructure and wear resistance of in-situ TiN/ (Nb, Ti) 5 Si 3 reinforced MoNbTaWTi-based refractory high entropy alloy composite coatings by laser cladding

Microstructure of NbMoTaTiNi Refractory High-Entropy Alloy Coating Fabricated by Ultrasonic Field-Assisted Laser Cladding Process

Evolution in microstructure and tribological behavior of laser cladded MoxNbTiZr high-entropy refractory alloy coatings with varying Mo content

Enhancement of hardness and high-temperature wear resistance of laser-clad CoAlTiWTa RHEA coating on inconel 718 superalloy by addition of TiC

Microstructure and wear property of WMoTaNb refractory high entropy alloy coating by laser cladding

Microstructure evolution and characteristics of laser-clad lightweight refractory NbxMo$_{0.5}$Ti$_{1.5}$Ta$_{0.2}$Cr high-entropy alloy

The CrFeNbTiMox refractory high-entropy alloy coatings prepared on the 40Cr by laser cladding

Evolution in Wear and High-Temperature Oxidation Resistance of Laser-Clad AlxMoNbTa Refractory High-Entropy Alloys Coatings with Al Addition Content

Lightweight refractory high entropy alloy coating by laser cladding on Ti–6Al–4V surface

Microstructure and high temperature properties of laser cladded WTaNbMo refractory high entropy alloy coating assisted with ultrasound vibration

Microstructure evolution and performance of TiMoCrW x Ta y refractory high-entropy alloy coatings prepared using laser cladding

Microstructure, thermostability and tribological behavior of composite CoCrFeNiTix high-entropy alloy coatings fabricated by laser cladding

Microstructure and wear behavior of mechanically alloyed powder AlxMo0.5NbFeTiMn2 high entropy alloy coating formed by laser cladding

Microstructure and wear resistance of in-situ TiC reinforced AlCoCrFeNi-based coatings by laser cladding

Microstructure and tribological properties of in-situ M x B reinforced CoCrFeNi HEA composites prepared by laser cladding

Microstructure of WTaNbMo refractory high entropy alloy coating fabricated by dynamic magnetic field assisted laser cladding process

Influence of laser power on microstructure and high-temperature tribological properties of CoAlTiWTa RHEA coating on Inconel 718 superalloy

Multi-objective optimization for laser cladding refractory MoNbTiZr high-entropy alloy coating on Ti6Al4V

Microstructure and Properties of CoCrFeNiMnTix High-Entropy Alloy Coated by Laser Cladding

Effect of Mo on Microstructures and Wear Properties of In Situ Synthesized Ti(C,N)/Ni-Based Composite Coatings by Laser Cladding

Wear-resistant NbMoTaWTi high entropy alloy coating prepared by laser cladding on TC4 titanium alloy