Abstract:Rare earth (RE) elements have large solid solubility in magnesium and are widely used to regulate the microstructure and property of advanced magnesium alloys. However, different kinds of RE elements have different effects on microstructure and property of the alloy. In this study, a Mg–Zn–Y alloy and a Mg–Zn–Gd alloy with alloying elements of the same atomic percentage were designed to clarify the effect of yttrium (Y) and gadolinium (Gd) on the corrosion behavior of as-cast MgZn 2 Y 2.66 and MgZn 2 Gd 2.66 alloys. The results show that the MgZn 2 Y 2.66 alloy is mainly composed of α-Mg phase and long period stacking ordered (LPSO) phase, while MgZn 2 Gd 2.66 alloy is mainly composed of α-Mg phase and (Mg, Gd) 3 Zn phase (W phase). Generally speaking, the corrosion phenomena of the two alloys in 3.5 wt% NaCl solution are similar. In the early stages of exposure, the alloys underwent uniform corrosion at a relatively low corrosion rate. With prolonged exposure, localized corrosion became dominated and the corrosion rate was greatly increased. However, the corrosion rate of the MgZn 2 Y 2.66 alloy, in terms of the corrosion current density, is about one order of magnitude lower than that of the MgZn 2 Gd 2.66 alloy. The high corrosion resistance of the MgZn 2 Y 2.66 alloy is mainly attributed to the presence of LPSO phase in form of continuous networks and the relatively high corrosion resistance of the corrosion product layer on the alloy.

Revealing the effect of Gd alloying on oxidation resistance and oxide film protection performance of AZ80 alloy

Comprehensive Unveiling of the Oxidation Resistance and Corrosion Protection of an Oxide Layer Formed on the Gd-Alloyed AZ80 Alloy Surface

High-temperature oxidation behavior and corrosion behavior of high strength Mg-xGd alloys with high Gd content

Improving the corrosion resistance of MgZn1.2Gd Zr0.18 (x = 0, 0.8, 1.4, 2.0) alloys via Gd additions

Effect of Gd on microstructure and stress corrosion cracking of the AZ91‐extruded magnesium alloy

Improving the corrosion resistance of Mg-8Li-3Al-2Zn alloy by combining Gd alloying and hot extrusion

Effect of minor Gd addition on microstructure, mechanical performance, and corrosion behavior of Mg–Y–Gd alloys

Effects of Gd on Microstructure and Mechanical Properties of AZ61 Magnesium Alloy

Influences of Gd on the Microstructure and Strength of Mg–4.5Zn Alloy

Effect of Ti Addition on the Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn Alloys

The high-temperature oxidation resistance properties of magnesium alloys alloyed with Gd and Ca

Improving tensile properties and corrosion resistance of Mg–Zn–Ca–Mn alloy via Gd addition

Effect of grain size and crystal orientation on the corrosion behavior of as-extruded Mg-6Gd-2Y-0.2Zr alloy

Effects of Y, Gd on Microstructure and Mechanical Properties of AZ61 Magnesium Alloy

Effect of Al addition on microstructure and mechanical properties of Mg−Gd−Zn alloys

Effect of Zn/(Gd+Y) ratio on the microstructure evolution and mechanical properties of Mg-Gd-Y-Zn-Zr alloy

Investigations on Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn-Zr-Nd Alloy

Comparative Study on Corrosion Behavior and Mechanism of As-Cast Mg–Zn–Y and Mg–Zn–Gd Alloys

Isothermal oxidation behaviour of TiAl alloys prepared by spark plasma sintering with the addition of Gd under water vapour at 900 °C

Comparison of the Corrosion Behaviors of Mg–Gd–Y–Zn–Zr Alloys Fabricated by Different Preparation Methods

Study of microstructure and corrosion resistance of FeCrAl-Gd alloys