Abstract:Silica nanoparticles are widely utilized abrasives in chemical mechanical polishing (CMP), and the modification of abrasives and the incorporation of chemical additives represent primary strategies for enhancing CMP performance. In this study, we achieved a modification of the electrical properties of the colloidal silica surface by forming a coating film through the "grafting" of 3-aminopropyltriethoxysilane (APTES) onto the colloidal silica surface. This modification resulted in an augmented mechanical interaction between the abrasive and the wafer during the CMP process, leading to an enhanced material removal rate (MRR) of SiO 2 . However, the post-CMP surface exhibited a relatively higher occurrence of surface defects. Subsequently, cetyltrimethylammonium bromide (CTAB) was added as an auxiliary additive, which promoted the formation of a "special electrostatic self-assembly structure" on the surface of the abrasive, further elevating the SiO 2 MRR. Moreover, CTAB demonstrated the capability to adsorb onto the wafer surface, creating a protective effect that resulted in reduced surface roughness and a decrease in surface defects following CMP. Furthermore, comprehensive characterization of the modified abrasive was conducted using techniques such as transmission electron microscopy (TEM) and scanning electron microscopy (SEM). The mechanisms underlying the improvement in CMP performance were systematically analyzed through experimental phenomena and X-ray photoelectron spectroscopy (XPS), and revealing that the introduction of CTAB indirectly facilitated the adsorption of APTES onto the surface of the colloidal silica. Our study provides a method for the advanced process of SiO 2 CMP with stringent metal ion requirements.

Effect of cations on the improvement of material removal rate of silicon wafer in chemical mechanical polishing

Chemical mechanical polishing of silicon wafers using developed uniformly dispersed colloidal silica in slurry

Improvement in chemical mechanical polishing of 4H-SiC wafer by activating persulfate through the synergistic effect of UV and TiO2

Chemical effect on the material removal rate in the CMP of silicon wafers

A special electrostatic self-assembly structure of colloidal silica: Improving Chemical Mechanical Polishing performance

Chemical Mechanical Planarization (cmp) of On-Axis Si-Face Sic Wafer Using Catalyst Nanoparticles in Slurry

Surface modulation to enhance chemical mechanical polishing performance of sliced silicon carbide Si-face

Chemical Mechanical Polishing (CMP) of On-Axis Si-face 6H-Sic Wafer for Obtaining Atomically Flat Defect-Free Surface

XPS, UV–vis Spectroscopy and AFM Studies on Removal Mechanisms of Si-face SiC Wafer Chemical Mechanical Polishing (CMP)

Oxidation Anisotropy of 4H-Sic Wafers During Chemical-Mechanical Polishing

Optimization of polishing fluid composition for single crystal silicon carbide by ultrasonic assisted chemical-mechanical polishing

Mechanism Exploration of the Effect of Polyamines on the Polishing Rate of Silicon Chemical Mechanical Polishing: A Study Combining Simulations and Experiments

Two-Step Chemical Mechanical Polishing of 4H-SiC (0001) Wafer

Investigation on Material Removal Mechanisms in Photocatalysis-Assisted Chemical Mechanical Polishing of 4H–SiC Wafers

Polishing Mechanism of CMP 4H-SiC Crystal Substrate (0001) Si Surface Based on an Alumina (Al2O3) Abrasive

Angstrom surface with high material removal rate for quartz glass induced by silk dissolved novel green chemical mechanical polishing

Chemical Mechanical Polishing of 4H-SiC Wafer with UV-LED Light

Enhancement of Selectivity for Chemical Mechanical Polishing by Ultra-High-Dose C and Si Ion Implantation

Unprecedented atomic surface of silicon induced by environmentally friendly chemical mechanical polishing

Study on Chemical Mechanical Polishing Performances of Sapphire Wafer (0001) Using Silica-Based Slurry

Improving monocrystalline silicon surface quality with chemical mechanical polishing using the slurry with the additive of isopropanol